2002 JEEP LIBERTY Voltage regulator

CHARGING SYSTEM
TABLE OF CONTENTS
page page
CHARGING SYSTEM
DESCRIPTION.........................22
OPERATION...........................22
DIAGNOSIS AND TESTING - CHARGING
SYSTEM............................22
SPECIFICATIONS
TORQUE - EXCEPT DIESEL.............23
GENERATOR RATINGS - GAS ENGINES . . . 23
SPECIAL TOOLS.......................24
BATTERY TEMPERATURE SENSOR
DESCRIPTION.........................24
OPERATION...........................24
REMOVAL.............................24
INSTALLATION.........................24
GENERATOR
DESCRIPTION.........................25OPERATION...........................25
REMOVAL.............................25
INSTALLATION.........................26
GENERATOR DECOUPLER PULLEY
DESCRIPTION.........................26
OPERATION...........................27
DIAGNOSIS AND TESTING - GENERATOR
DECOUPLER.........................27
REMOVAL.............................27
INSTALLATION.........................30
VOLTAGE REGULATOR
DESCRIPTION.........................31
OPERATION...........................31
CHARGING SYSTEM
DESCRIPTION
The charging system consists of:
²Generator
²Electronic Voltage Regulator (EVR) circuitry
within the Powertrain Control Module (PCM)
²Ignition switch
²Battery (refer to 8, Battery for information)
²Battery temperature sensor
²Generator Lamp (if equipped)
²Check Gauges Lamp (if equipped)
²Wiring harness and connections (refer to 8, Wir-
ing for information)
OPERATION
The charging system is turned on and off with the
ignition switch. The system is on when the engine is
running and the ASD relay is energized. When the
ASD relay is on, voltage is supplied to the ASD relay
sense circuit at the PCM. This voltage is connected
through the PCM and supplied to one of the genera-
tor field terminals (Gen. Source +) at the back of the
generator.
The amount of DC current produced by the gener-
ator is controlled by the EVR (field control) circuitry
contained within the PCM. This circuitry is con-
nected in series with the second rotor field terminal
and ground.
A battery temperature sensor, located in the bat-
tery tray housing, is used to sense battery tempera-ture. This temperature data, along with data from
monitored line voltage, is used by the PCM to vary
the battery charging rate. This is done by cycling the
ground path to control the strength of the rotor mag-
netic field. The PCM then compensates and regulates
generator current output accordingly.
All vehicles are equipped with On-Board Diagnos-
tics (OBD). All OBD-sensed systems, including EVR
(field control) circuitry, are monitored by the PCM.
Each monitored circuit is assigned a Diagnostic Trou-
ble Code (DTC). The PCM will store a DTC in elec-
tronic memory for certain failures it detects. Refer to
Diagnostic Trouble Codes in; Powertrain Control
Module; Electronic Control Modules for more DTC
information.
The Check Gauges Lamp (if equipped) monitors:
charging system voltage,engine coolant tempera-
ture and engine oil pressure. If an extreme condition
is indicated, the lamp will be illuminated. This is
done as reminder to check the three gauges. The sig-
nal to activate the lamp is sent via the CCD bus cir-
cuits. The lamp is located on the instrument panel.
Refer to 8, Instrument Cluster for additional infor-
mation.
DIAGNOSIS AND TESTING - CHARGING
SYSTEM
The following procedures may be used to diagnose
the charging system if:
²the check gauges lamp (if equipped) is illumi-
nated with the engine running
8F - 22 CHARGING SYSTEMKJ

VOLTAGE REGULATOR
DESCRIPTION
The Electronic Voltage Regulator (EVR) is not a
separate component. It is actually a voltage regulat-
ing circuit located within the Powertrain Control
Module (PCM). The EVR is not serviced separately. If
replacement is necessary, the PCM must be replaced.
OPERATION
The amount of DC current produced by the gener-
ator is controlled by EVR circuitry contained within
the Powertrain Control Module (PCM). This circuitry
is connected in series with the generators second
rotor field terminal and its ground.
Voltage is regulated by cycling the ground path to
control the strength of the rotor magnetic field. TheEVR circuitry monitors system line voltage (B+) and
battery temperature (refer to Battery Temperature
Sensor for more information). It then determines a
target charging voltage. If sensed battery voltage is
0.5 volts or lower than the target voltage, the PCM
grounds the field winding until sensed battery volt-
age is 0.5 volts above target voltage. A circuit in the
PCM cycles the ground side of the generator field up
to 100 times per second (100Hz), but has the capabil-
ity to ground the field control wire 100% of the time
(full field) to achieve the target voltage. If the charg-
ing rate cannot be monitored (limp-in), a duty cycle
of 25% is used by the PCM in order to have some
generator output. Also refer to Charging Operation
for additional information.
KJCHARGING SYSTEM 8F - 31

FUEL PUMP
DESCRIPTION
The electric fuel pump is located inside of the fuel
pump module. A 12 volt, permanent magnet, electric
motor powers the fuel pump. The electric fuel pump
is not a separate, serviceable component.
OPERATION
Voltage to operate the electric pump is supplied
through the fuel pump relay.
Fuel is drawn in through a filter at the bottom of
the module and pushed through the electric motor
gearset to the pump outlet.
Check Valve Operation:The bottom section of
the fuel pump module contains a one-way check
valve to prevent fuel flow back into the tank and to
maintain fuel supply line pressure (engine warm)
when pump is not operational. It is also used to keep
the fuel supply line full of gasoline when pump is not
operational. After the vehicle has cooled down, fuel
pressure may drop to 0 psi (cold fluid contracts), but
liquid gasoline will remain in fuel supply line
between the check valve and fuel injectors.Fuel
pressure that has dropped to 0 psi on a cooled
down vehicle (engine off) is a normal condition.
Refer to the Fuel Pressure Leak Down Test for more
information.
The electric fuel pump is not a separate, service-
able component.
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - FUEL PUMP
CAPACITY TEST
Before performing this test, verify fuel pump
pressure. Refer to Fuel Pump Pressure Test.
Use this test in conjunction with the Fuel Pres-
sure Leak Down Test.
(1) Release fuel system pressure. Refer to Fuel
Pressure Release Procedure.
(2) Disconnect fuel supply line at fuel rail. Refer to
Quick-Connect Fittings. Some engines may require
air cleaner housing removal before line disconnection.
(3) Obtain correct Fuel Line Pressure Test Adapter
Tool Hose. Tool number 6539 is used for 5/16º fuel
lines and tool number 6631 is used for 3/8º fuel lines.
(4) Connect correct Fuel Line Pressure Test
Adapter Tool Hose into disconnected fuel supply line.
Insert other end of Adaptor Tool Hose into a gradu-
ated container.
(5) Remove fuel fill cap.(6) To activate fuel pump and pressurize system,
obtain DRBtscan tool and actuate ASD Fuel System
Test.
(7) A good fuel pump will deliver at least 1/10 liter
of fuel in 7 seconds. Do not operate fuel pump for
longer than 7 seconds with fuel line disconnected as
fuel pump module reservoir may run empty.
(a) If capacity is lower than specification, but
fuel pump can be heard operating through fuel fill
cap opening, check for a kinked/damaged fuel sup-
ply line somewhere between fuel rail and fuel
pump module.
(b) If line is not kinked/damaged, and fuel pres-
sure is OK, but capacity is low, replace fuel filter.
Refer to Fuel Filter Removal/Installation for addi-
tional information.
(c) If both fuel pressure and capacity are low,
replace bottom section of fuel pump module. Refer
to Fuel Pump Module Removal/Installation.
DIAGNOSIS AND TESTING - FUEL PUMP
PRESSURE TEST
Use this test in conjunction with the Fuel Pump
Capacity Test, Fuel Pressure Leak Down Test and
Fuel Pump Amperage Test found elsewhere in this
group.
Check Valve Operation:The bottom section of
the fuel pump module contains a one-way check
valve to prevent fuel flow back into the tank and to
maintain fuel supply line pressure (engine warm)
when pump is not operational. It is also used to keep
the fuel supply line full of gasoline when pump is not
operational. After the vehicle has cooled down, fuel
pressure may drop to 0 psi (cold fluid contracts), but
liquid gasoline will remain in fuel supply line
between the check valve and fuel injectors.Fuel
pressure that has dropped to 0 psi on a cooled
down vehicle (engine off) is a normal condition.
When the electric fuel pump is activated, fuel pres-
sure shouldimmediately(1±2 seconds) rise to spec-
ification.
The fuel system is equipped with a separate fuel
pump module mounted, fuel pressure regulator. The
fuel filter is remotely mounted. The fuel pressure
regulator is not controlled by engine vacuum.
WARNING: THE FUEL SYSTEM IS UNDER CON-
STANT FUEL PRESSURE EVEN WITH THE ENGINE
OFF. BEFORE DISCONNECTING FUEL LINE AT
FUEL RAIL, THIS PRESSURE MUST BE RELEASED.
REFER TO THE FUEL SYSTEM PRESSURE
RELEASE PROCEDURE.
KJFUEL DELIVERY 14 - 15

an associated limp in will take two trips to illumi-
nate the MIL.
Refer to the Diagnostic Trouble Codes Description
Charts in this section and the appropriate Power-
train Diagnostic Procedure Manual for diagnostic
procedures.
DESCRIPTION - NON-MONITORED CIRCUITS
The PCM does not monitor the following circuits,
systems and conditions that could have malfunctions
causing driveability problems. The PCM might not
store diagnostic trouble codes for these conditions.
However, problems with these systems may cause the
PCM to store diagnostic trouble codes for other sys-
tems or components. For example, a fuel pressure
problem will not register a fault directly, but could
cause a rich/lean condition or misfire. This could
cause the PCM to store an oxygen sensor or misfire
diagnostic trouble code
FUEL PRESSURE
The fuel pressure regulator controls fuel system
pressure. The PCM cannot detect a clogged fuel
pump inlet filter, clogged in-line fuel filter, or a
pinched fuel supply or return line. However, these
could result in a rich or lean condition causing the
PCM to store an oxygen sensor or fuel system diag-
nostic trouble code.
SECONDARY IGNITION CIRCUIT
The PCM cannot detect an inoperative ignition coil,
fouled or worn spark plugs, ignition cross firing, or
open spark plug cables.
CYLINDER COMPRESSION
The PCM cannot detect uneven, low, or high engine
cylinder compression.
EXHAUST SYSTEM
The PCM cannot detect a plugged, restricted or
leaking exhaust system, although it may set a fuel
system fault.
FUEL INJECTOR MECHANICAL MALFUNCTIONS
The PCM cannot determine if a fuel injector is
clogged, the needle is sticking or if the wrong injectoris installed. However, these could result in a rich or
lean condition causing the PCM to store a diagnostic
trouble code for either misfire, an oxygen sensor, or
the fuel system.
EXCESSIVE OIL CONSUMPTION
Although the PCM monitors engine exhaust oxygen
content when the system is in closed loop, it cannot
determine excessive oil consumption.
THROTTLE BODY AIRFLOW
The PCM cannot detect a clogged or restricted air
cleaner inlet or filter element.
VACUUM ASSIST
The PCM cannot detect leaks or restrictions in the
vacuum circuits of vacuum assisted engine control
system devices. However, these could cause the PCM
to store a MAP sensor diagnostic trouble code and
cause a high idle condition.
PCM SYSTEM GROUND
The PCM cannot determine a poor system ground.
However, one or more diagnostic trouble codes may
be generated as a result of this condition. The mod-
ule should be mounted to the body at all times, also
during diagnostic.
PCM CONNECTOR ENGAGEMENT
The PCM may not be able to determine spread or
damaged connector pins. However, it might store
diagnostic trouble codes as a result of spread connec-
tor pins.
DESCRIPTION - HIGH AND LOW LIMITS
The PCM compares input signal voltages from each
input device with established high and low limits for
the device. If the input voltage is not within limits
and other criteria are met, the PCM stores a diagnos-
tic trouble code in memory. Other diagnostic trouble
code criteria might include engine RPM limits or
input voltages from other sensors or switches that
must be present before verifying a diagnostic trouble
code condition.
DESCRIPTION - LOAD VALUE
ENGINE IDLE/NEUTRAL 2500 RPM/NEUTRAL
All Engines 2% to 8% of Maximum Load 9% to 17% of Maximum Load
25 - 20 EMISSIONS CONTROLKJ
EMISSIONS CONTROL (Continued)

DIFFERENTIAL - TRAC-LOK - CLEANING . . 3-109,
3-77
DIFFERENTIAL - TRAC-LOK -
DISASSEMBLY...................3-107,3-75
DIFFERENTIAL - TRAC-LOK -
INSPECTION....................3-109,3-77
DIFFERENTIAL CASE BEARINGS -
INSTALLATION...............3-110,3-44,3-79
DIFFERENTIAL CASE BEARINGS -
REMOVAL..................3-110,3-43,3-79
DIMENSIONS - SPECIFICATIONS, FRAME . . . 13-3
DIMENSIONS - SPECIFICATIONS,
OPENING..........................23-111
DIODE - INSTALLATION............8W-01-14
DIODE - REMOVAL................8W-01-14
DIODE REPLACEMENT - STANDARD
PROCEDURE.........................24-9
DISASSEMBLY - POWER DISTRIBUTION
CENTER DISASSEMBLY.............8W-97-7
DISASSEMBLY, 4C RETAINER/BULKHEAD . 21-122
DISASSEMBLY, DIAGNOSIS AND
TESTING...........................21-83
DISASSEMBLY, DIFFERENTIAL......3-105,3-41
DISASSEMBLY, DIFFERENTIAL -
TRAC-LOK......................3-107,3-75
DISASSEMBLY, DISASSEMBLY - POWER
DISTRIBUTION CENTER.............8W-97-7
DISASSEMBLY, DISC BRAKE CALIPERS....5-14
DISASSEMBLY, HVAC HOUSING.........24-34
DISASSEMBLY, INPUT CLUTCH
ASSEMBLY.........................21-135
DISASSEMBLY, INSTRUMENT CLUSTER....8J-9
DISASSEMBLY, LOW/REVERSE CLUTCH . . 21-145
DISASSEMBLY, MANUAL - NV1500........21-4
DISASSEMBLY, MANUAL - NV3550.......21-35
DISASSEMBLY, OIL PUMP...............9-65
DISASSEMBLY, OIL PUMP.............21-149
DISASSEMBLY, PLANETARY GEARTRAIN . 21-159
DISASSEMBLY, SINGLE CARDAN
UNIVERSAL JOINTS....................3-8
DISASSEMBLY, TRANSFER CASE -
NV231............................21-182
DISASSEMBLY, TRANSFER CASE -
NV242............................21-218
DISASSEMBLY, VALVE BODY...........21-173
DISASSEMBLY, WHEEL CYLINDERS.......5-28
DISC - INSTALLATION, CLUTCH...........6-6
DISC - REMOVAL, CLUTCH...............6-6
DISC BRAKE CALIPER ADAPTER -
INSTALLATION........................5-18
DISC BRAKE CALIPER ADAPTER -
REMOVAL...........................5-18
DISC BRAKE CALIPERS - ASSEMBLY......5-16
DISC BRAKE CALIPERS - CLEANING......5-16
DISC BRAKE CALIPERS - DESCRIPTION....5-13
DISC BRAKE CALIPERS - DISASSEMBLY . . . 5-14
DISC BRAKE CALIPERS - INSPECTION.....5-16
DISC BRAKE CALIPERS - INSTALLATION . . . 5-17
DISC BRAKE CALIPERS - OPERATION.....5-14
DISC BRAKE CALIPERS - REMOVAL.......5-14
DISC BRAKE ROTOR - DIAGNOSIS AND
TESTING............................5-18
DISC BRAKE ROTOR - STANDARD
PROCEDURE.........................5-19
DISCHARGE (ESD) SENSITIVE DEVICES -
STANDARD PROCEDURE,
ELECTROSTATIC...................8W-01-8
DISCHARGE LINE - INSTALLATION, A/C . . . 24-47
DISCHARGE LINE - REMOVAL, A/C.......24-46
DISPLAY TEST MODE - DESCRIPTION,
STATE ..............................25-2
DISTRIBUTION - DESCRIPTION, POWER . 8W-97-1
DISTRIBUTION - OPERATION, POWER . . 8W-97-1
DISTRIBUTION CENTER - DESCRIPTION,
POWER..........................8W-97-6
DISTRIBUTION CENTER - OPERATION,
POWER..........................8W-97-7
DISTRIBUTION CENTER - REMOVAL,
POWER..........................8W-97-7
DISTRIBUTION CENTER ASSEMBLY,
ASSEMBLY - POWER
..............8W-97-10
DISTRIBUTION CENTER DISASSEMBLY,
DISASSEMBLY - POWER
............8W-97-7
DISTRIBUTION SYSTEMS, SPECIAL
TOOLS - POWER
...................8W-97-2
DOO - INSTALLATION, FLOOR -
DEFROST
...........................24-37
DOOR - INSTALLATION
.........23-122,23-129DOOR - INSTALLATION, BLEND.........24-35
DOOR - INSTALLATION, PANEL..........24-36
DOOR - INSTALLATION, PASSENGER
AIRBAG............................8O-30
DOOR - INSTALLATION, RECIRC.........24-37
DOOR - REMOVAL.............23-122,23-129
DOOR - REMOVAL, BLEND.............24-35
DOOR - REMOVAL, DEFROST...........24-35
DOOR - REMOVAL, FLOOR - DEFROST....24-36
DOOR - REMOVAL, PASSENGER AIRBAG . . 8O-29
DOOR - REMOVAL, RECIRC............24-37
DOOR ACTUATOR - INSTALLATION,
BLEND.............................24-20
DOOR ACTUATOR - INSTALLATION,
FLOOR - DEFROST...................24-25
DOOR ACTUATOR - INSTALLATION,
PANEL.............................24-25
DOOR ACTUATOR - INSTALLATION,
RECIRCULATION.....................24-26
DOOR ACTUATOR - REMOVAL, BLEND....24-20
DOOR ACTUATOR - REMOVAL, FLOOR -
DEFROST...........................24-24
DOOR ACTUATOR - REMOVAL, PANEL....24-24
DOOR ACTUATOR - REMOVAL,
RECIRCULATION.....................24-26
DOOR AJAR INDICATOR - DESCRIPTION . . 8J-17
DOOR AJAR INDICATOR - OPERATION....8J-17
DOOR AJAR SWITCH - DESCRIPTION....8L-77
DOOR AJAR SWITCH - OPERATION........8L-77
DOOR CYLINDER LOCK SWITCH -
DESCRIPTION........................8Q-9
DOOR CYLINDER LOCK SWITCH -
DIAGNOSIS AND TESTING.............8Q-10
DOOR CYLINDER LOCK SWITCH -
INSTALLATION......................8Q-10
DOOR CYLINDER LOCK SWITCH -
OPERATION.........................8Q-10
DOOR CYLINDER LOCK SWITCH -
REMOVAL..........................8Q-10
DOOR GLASS - INSTALLATION . . 23-122,23-129,
23-172
DOOR GLASS - REMOVAL......23-122,23-129,
23-172
DOOR LOCK / UNLOCK SWITCH -
INSTALLATION.......................8N-5
DOOR LOCK / UNLOCK SWITCH -
REMOVAL...........................8N-4
DOOR LOCK MOTOR - DESCRIPTION......8N-5
DOOR LOCK MOTOR - DIAGNOSIS AND
TESTING............................8N-5
DOOR LOCK MOTOR - OPERATION.......8N-5
DOOR LOCK RELAY - DESCRIPTION......8N-6
DOOR LOCK RELAY - DIAGNOSIS AND
TESTING............................8N-6
DOOR LOCK RELAY - INSTALLATION......8N-7
DOOR LOCK RELAY - OPERATION........8N-6
DOOR LOCK RELAY - REMOVAL.........8N-6
DOOR LOCK/UNLOCK SWITCH -
DIAGNOSIS AND TESTING..............8N-4
DOOR LOWER WEATHERSTRIP -
INSTALLATION......................23-186
DOOR LOWER WEATHERSTRIP -
REMOVAL.........................23-186
DOOR OUTER BELT MOLDING -
INSTALLATION, FRONT...............23-186
DOOR OUTER BELT MOLDING -
INSTALLATION, REAR................23-186
DOOR OUTER BELT MOLDING -
REMOVAL, FRONT...................23-186
DOOR OUTER BELT MOLDING -
REMOVAL, REAR....................23-186
DOOR PRIMARY WEATHERSTRIP -
INSTALLATION......................23-185
DOOR PRIMARY WEATHERSTRIP -
REMOVAL.........................23-185
DOOR SCUFF PLATE - INSTALLATION,
REAR.............................23-160
DOOR SCUFF PLATE - REMOVAL, REAR . . 23-160
DOOR SILL SCUFF PLATE -
INSTALLATION......................23-157
DOOR SILL SCUFF PLATE - REMOVAL
. . . 23-157
DOOR/HOUSING - INSTALLATION, FUEL
FILL
..............................23-141
DOOR/HOUSING - REMOVAL, FUEL FILL
. 23-141
DOUBLE INVERTED FLARING -
STANDARD PROCEDURE
.................5-8
DRAIN AND FILL - STANDARD
PROCEDURE, FLUID
...........21-208,21-246DRAIN TUBE - INSTALLATION..........23-181
DRAIN TUBE - REMOVAL.............23-180
DRAINAGE AND WIND NOISE
DIAGNOSIS, DIAGNOSIS AND TESTING
- WATER ..........................23-176
DRAINING COOLING SYSTEM 3.7L
ENGINE - STANDARD PROCEDURE........7-12
DRAW TEST - STANDARD PROCEDURE,
IGNITION-OFF.......................8F-14
DRIVE - DIAGNOSIS AND TESTING,
VISCOUS FAN........................7-28
DRIVE BELT - DIAGNOSIS AND TESTING,
SERPENTINE.........................7-15
DRIVE MOTOR - INSTALLATION........23-182
DRIVE MOTOR - REMOVAL............23-182
DRIVER AIRBAG - DESCRIPTION........8O-17
DRIVER AIRBAG - INSTALLATION.......8O-20
DRIVER AIRBAG - OPERATION..........8O-18
DRIVER AIRBAG - REMOVAL...........8O-19
DRIVER SEAT HEATER SWITCH -
DESCRIPTION.......................8G-11
DRIVER SEAT HEATER SWITCH -
INSTALLATION......................8G-13
DRIVER SEAT HEATER SWITCH -
OPERATION.........................8G-12
DRIVER SEAT HEATER SWITCH -
REMOVAL..........................8G-13
DRIVER SIDE BEZELS - INSTALLATION,
INSTRUMENT PANEL.................23-154
DRIVER SIDE BEZELS - REMOVAL,
INSTRUMENT PANEL.................23-153
DROP - STANDARD PROCEDURE,
TESTING FOR A VOLTAGE...........8W-01-10
DRUM - DIAGNOSIS AND TESTING,
BRAKE..............................5-27
DRUM BRAKE - ADJUSTMENT, REAR......5-12
DRUM BRAKE - DESCRIPTION, REAR.....5-10
DRUM BRAKE - OPERATION, REAR.......5-11
DRUM BRAKE SHOES - INSTALLATION....5-11
DRUM BRAKE SHOES - REMOVAL........5-11
DRUM MACHINING - STANDARD
PROCEDURES, BRAKE.................5-27
DUCT - INSTALLATION, DEFROST/
DEMISTER..........................24-32
DUCT - INSTALLATION, FLOOR..........24-32
DUCT - INSTALLATION, FLOOR CONSOLE . 24-31
DUCT - REMOVAL, FLOOR.............24-32
DUCT - REMOVAL, FLOOR CONSOLE.....24-31
DUCT/DEMISTER ADAPTOR - REMOVAL,
DEFROST...........................24-32
EFFECTS OF INCORRECT FLUID LEVEL -
DIAGNOSIS AND TESTING............21-125
ELECTRIC - DESCRIPTION, RADIATOR
FAN ................................7-26
ELECTRIC - INSTALLATION, RADIATOR
FAN ................................7-27
ELECTRIC - INSTALLATION, WINDOW
REGULATOR.................23-126,23-134
ELECTRIC - OPERATION, RADIATOR FAN . . . 7-26
ELECTRIC - REMOVAL, RADIATOR FAN....7-26
ELECTRIC - REMOVAL, WINDOW
REGULATOR.................23-126,23-134
ELECTRICAL - DESCRIPTION............5-34
ELECTRICAL - OPERATION..............5-34
ELECTRICAL TESTER - STANDARD
PROCEDURE, USING MIDTRONICS.......8F-15
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE DEVICES - STANDARD
PROCEDURE......................8W-01-8
ELEMENT - DESCRIPTION, HEATED SEAT . 8G-13
ELEMENT - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-13
ELEMENT - OPERATION, HEATED SEAT . . . 8G-13
EMISSION CONTROL INFORMATION
(VECI) LABEL - DESCRIPTION,
VEHICLE..........................Intro.-8
EMISSION CONTROL SYSTEM -
DESCRIPTION........................25-1
END - INSTALLATION, TIE ROD.........19-16
END - REMOVAL, TIE ROD.............19-16
END CAP - INSTALLATION, INSTRUMENT
PANEL
............................23-153
END CAP - REMOVAL, INSTRUMENT
PANEL
............................23-153
END REMOVAL TOOL, SPECIAL TOOLS -
OUTER TIE ROD
.....................19-15
ENGINE - 3.7L - DESCRIPTION
............9-3
ENGINE - DESCRIPTION, 3.7L
............7-21
8 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-46
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-45
PLATES - INSTALLATION, EXTERIOR
NAME............................23-141
PLATES - REMOVAL, EXTERIOR NAME . . . 23-140
PLUG - CLEANING SPARK PLUGS,
SPARK .............................8I-15
PLUG - DESCRIPTION, SPARK...........8I-12
PLUG - INSTALLATION, SPARK..........8I-15
PLUG - OPERATION, SPARK............8I-12
PLUG - REMOVAL, SPARK..............8I-15
PLUG CABLE RESISTANCE, 2.4L - SPARK . . . 8I-3
PLUG CONDITIONS - DIAGNOSIS AND
TESTING, SPARK.....................8I-13
PLUGS - STANDARD PROCEDURE,
ENGINE CORE AND OIL GALLERY........9-10
PLUGS, SPARK PLUG - CLEANING
SPARK .............................8I-15
PLUGS, SPECIFICATIONS - SPARK........8I-3
POLISHING - DESCRIPTION, FINESSE
SANDING/BUFFING..................23-163
PORT - DESCRIPTION, REFRIGERANT
SYSTEM SERVICE.....................24-2
PORT - OPERATION, REFRIGERANT
SYSTEM SERVICE.....................24-2
POSITION LAMP BULB - INSTALLATION,
FRONT.............................8L-28
POSITION LAMP BULB - REMOVAL,
FRONT.............................8L-28
POSITION SENSOR - DESCRIPTION . 21-209,21-247
POSITION SENSOR - DESCRIPTION,
CRANKSHAFT.......................14-30
POSITION SENSOR - DESCRIPTION,
THROTTLE..........................14-47
POSITION SENSOR - INSTALLATION....21-210,
21-247
POSITION SENSOR - INSTALLATION,
CRANKSHAFT.......................14-32
POSITION SENSOR - INSTALLATION,
THROTTLE..........................14-48
POSITION SENSOR - OPERATION . 21-209,21-247
POSITION SENSOR - OPERATION,
CRANKSHAFT.......................14-31
POSITION SENSOR - OPERATION,
THROTTLE..........................14-47
POSITION SENSOR - REMOVAL . . 21-210,21-247
POSITION SENSOR - REMOVAL,
CRANKSHAFT.......................14-31
POSITION SENSOR - REMOVAL,
THROTTLE..........................14-47
POSITION SWITCH - DESCRIPTION,
CLUTCH PEDAL.......................6-11
POSITION SWITCH - DIAGNOSIS AND
TESTING, CLUTCH PEDAL...............6-11
POSITION SWITCH - OPERATION,
CLUTCH PEDAL.......................6-11
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE..............8W-01-9
POWER BRAKE BOOSTER -
DESCRIPTION........................5-21
POWER BRAKE BOOSTER -
INSTALLATION........................5-23
POWER BRAKE BOOSTER - OPERATION . . . 5-21
POWER BRAKE BOOSTER - REMOVAL.....5-22
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION CENTER -
DESCRIPTION.....................8W-97-6
POWER DISTRIBUTION CENTER -
OPERATION.......................8W-97-7
POWER DISTRIBUTION CENTER -
REMOVAL........................8W-97-7
POWER DISTRIBUTION CENTER
ASSEMBLY, ASSEMBLY.............8W-97-10
POWER DISTRIBUTION CENTER
DISASSEMBLY, DISASSEMBLY........8W-97-7
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS...................8W-97-2
POWER GROUNDS - DESCRIPTION......8E-13
POWER LOCKS - DESCRIPTION
..........8N-1
POWER LOCKS - DIAGNOSIS AND
TESTING
............................8N-3
POWER LOCKS - OPERATION
............8N-3
POWER MIRROR SWITCH - DIAGNOSIS
AND TESTING
.......................8N-12
POWER MIRROR SWITCH -
INSTALLATION
......................8N-13POWER MIRROR SWITCH - REMOVAL . . . 8N-13
POWER MIRRORS - DESCRIPTION......8N-11
POWER MIRRORS - DIAGNOSIS AND
TESTING...........................8N-11
POWER MIRRORS - OPERATION........8N-11
POWER OUTLET - DESCRIPTION.....8W-97-11
POWER OUTLET - DIAGNOSIS AND
TESTING........................8W-97-11
POWER OUTLET - INSTALLATION....8W-97-13
POWER OUTLET - OPERATION.......8W-97-11
POWER OUTLET - REMOVAL........8W-97-12
POWER SEAT SWITCH - DESCRIPTION,
LEFT..............................8N-16
POWER SEAT SWITCH - DESCRIPTION,
RIGHT.............................8N-19
POWER SEAT SWITCH - DIAGNOSIS
AND TESTING, LEFT..................8N-17
POWER SEAT SWITCH - DIAGNOSIS
AND TESTING, RIGHT.................8N-19
POWER SEAT SWITCH - INSTALLATION,
LEFT..............................8N-18
POWER SEAT SWITCH - INSTALLATION,
RIGHT.............................8N-20
POWER SEAT SWITCH - OPERATION,
LEFT..............................8N-17
POWER SEAT SWITCH - OPERATION,
RIGHT.............................8N-19
POWER SEAT SWITCH - REMOVAL, LEFT . 8N-18
POWER SEAT SWITCH - REMOVAL,
RIGHT.............................8N-20
POWER SEATS - DESCRIPTION...........8N-14
POWER SEATS - DIAGNOSIS AND
TESTING...........................8N-15
POWER SEATS - OPERATION...........8N-15
POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-3
POWER STEERING PRESSURE SWITCH -
DESCRIPTION.......................19-22
POWER STEERING PRESSURE SWITCH -
INSTALLATION.......................19-22
POWER STEERING PRESSURE SWITCH -
OPERATION.........................19-22
POWER STEERING PRESSURE SWITCH -
REMOVAL..........................19-22
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE . . . 19-18
POWER STEERING PUMP, SPECIAL
TOOLS.............................19-20
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING..............19-1
POWER WINDOWS - DESCRIPTION......8N-21
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-21
POWER WINDOWS - OPERATION........8N-21
POWERED - STARTER MOTOR, GAS......8F-39
POWERED - TORQUE, GAS.............8F-38
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-9
PRECAUTIONS - CAUTION,
REFRIGERANT HOSES/LINES/TUBES
......24-40
PRECAUTIONS - OPERATION, SERVICE
....19-5
PRECAUTIONS AND WARNINGS,
WARNING - SAFETY
...................23-1
PRECAUTIONS, WARNING -
WINDSHIELD SAFETY
................23-173
PREFERENCES - STANDARD
PROCEDURE, RKE TRANSMITTER
CUSTOMER
..........................8N-8
PRELIMINARY - DIAGNOSIS AND
TESTING
...........................21-78
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING
.........................7-3
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE
.............................9-9
PRESS CONTAINER - DESCRIPTION,
COOLANT RECOVERY
..................7-19
PRESS CONTAINER - OPERATION,
COOLANT RECOVERY
..................7-19
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION
...............9-8
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL
..........................9-60
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW
...............19-3PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-5
PRESSURE CAP - CLEANING, RADIATOR . . . 7-25
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-25
PRESSURE CAP - DIAGNOSIS AND
TESTING, RADIATOR...................7-25
PRESSURE CAP - INSPECTION,
RADIATOR...........................7-25
PRESSURE CAP - OPERATION,
RADIATOR...........................7-25
PRESSURE HOSE - INSTALLATION.......19-21
PRESSURE HOSE - REMOVAL..........19-21
PRESSURE INDICATOR - DESCRIPTION,
LOW OIL ...........................8J-23
PRESSURE INDICATOR - OPERATION,
LOW OIL ...........................8J-23
PRESSURE LEAK DOWN TEST -
DIAGNOSIS AND TESTING, FUEL.........14-3
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION........9-8
PRESSURE (LP) SENSOR -
DESCRIPTION, LINE.................21-144
PRESSURE (LP) SENSOR -
INSTALLATION, LINE.................21-144
PRESSURE (LP) SENSOR - OPERATION,
LINE..............................21-144
PRESSURE (LP) SENSOR - REMOVAL,
LINE..............................21-144
PRESSURE REGULATOR - DESCRIPTION,
FUEL..............................14-13
PRESSURE REGULATOR -
INSTALLATION, FUEL...................14-14
PRESSURE REGULATOR - OPERATION,
FUEL..............................14-14
PRESSURE REGULATOR - REMOVAL,
FUEL..............................14-14
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-4
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-42
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-42
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-65
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL....................9-65
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-65
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL.......................9-65
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM............................14-5
PRESSURE SWITCH - DESCRIPTION, A/C
HIGH..............................24-17
PRESSURE SWITCH - DESCRIPTION, A/C
LOW ..............................24-18
PRESSURE SWITCH - DESCRIPTION,
POWER STEERING...................19-22
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C HIGH...................24-18
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C LOW
...................24-19
PRESSURE SWITCH - INSTALLATION,
A/C HIGH
...........................24-18
PRESSURE SWITCH - INSTALLATION,
A/C LOW
...........................24-19
PRESSURE SWITCH - INSTALLATION,
POWER STEERING
...................19-22
PRESSURE SWITCH - OPERATION, A/C
HIGH
..............................24-18
PRESSURE SWITCH - OPERATION, A/C
LOW
..............................24-18
PRESSURE SWITCH - OPERATION,
POWER STEERING
...................19-22
PRESSURE SWITCH - REMOVAL, A/C
HIGH
..............................24-18
PRESSURE SWITCH - REMOVAL, A/C
LOW
..............................24-19
PRESSURE SWITCH - REMOVAL,
POWER STEERING
...................19-22
PRESSURE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP
.................14-15
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC
.................21-79
PRIMARY WEATHERSTRIP -
INSTALLATION, DOOR
................23-185
KJINDEX 19
Description Group-Page Description Group-Page Description Group-Page

REAR SEAT BACK LATCH STRIKER -
INSTALLATION......................23-171
REAR SEAT BACK LATCH STRIKER -
REMOVAL.........................23-170
REAR SEAT BELT BUCKLE -
INSTALLATION......................8O-35
REAR SEAT BELT BUCKLE - REMOVAL . . . 8O-34
REAR SUSPENSION - DIAGNOSIS AND
TESTING............................2-17
REAR TOW HOOK - INSTALLATION.......13-8
REAR TOW HOOK - REMOVAL...........13-8
REAR VIEW MIRROR - REMOVAL.......23-161
REAR WASHER HOSES/TUBES -
DESCRIPTION.......................8R-35
REAR WASHER HOSES/TUBES -
OPERATION.........................8R-36
REAR WASHER NOZZLE - DESCRIPTION . . 8R-36
REAR WASHER NOZZLE - INSTALLATION . 8R-37
REAR WASHER NOZZLE - OPERATION....8R-36
REAR WASHER NOZZLE - REMOVAL.....8R-36
REAR WHEEL OPENING FLARE
MOLDINGS - INSTALLATION...........23-145
REAR WHEEL OPENING FLARE
MOLDINGS - REMOVAL..............23-145
REAR WHEEL SPEED SENSOR -
INSTALLATION........................5-35
REAR WHEEL SPEED SENSOR -
REMOVAL...........................5-35
REAR WHEELHOUSE SPLASH SHIELD -
INSTALLATION......................23-144
REAR WHEELHOUSE SPLASH SHIELD -
REMOVAL.........................23-144
REAR WINDOW DEFOGGER -
DESCRIPTION........................8G-3
REAR WINDOW DEFOGGER -
OPERATION..........................8G-3
REAR WINDOW DEFOGGER GRID -
DESCRIPTION........................8G-5
REAR WINDOW DEFOGGER GRID -
DIAGNOSIS AND TESTING..............8G-5
REAR WINDOW DEFOGGER GRID -
OPERATION..........................8G-5
REAR WINDOW DEFOGGER RELAY -
DESCRIPTION........................8G-6
REAR WINDOW DEFOGGER RELAY -
DIAGNOSIS AND TESTING..............8G-6
REAR WINDOW DEFOGGER RELAY -
INSTALLATION.......................8G-7
REAR WINDOW DEFOGGER RELAY -
OPERATION..........................8G-6
REAR WINDOW DEFOGGER RELAY -
REMOVAL...........................8G-7
REAR WINDOW DEFOGGER SWITCH -
DESCRIPTION........................8G-8
REAR WINDOW DEFOGGER SWITCH -
DIAGNOSIS AND TESTING..............8G-8
REAR WINDOW DEFOGGER SWITCH -
OPERATION..........................8G-8
REAR WINDOW DEFOGGER SYSTEM -
DIAGNOSIS AND TESTING..............8G-4
REAR WIPER & WASHER SYSTEM -
CLEANING..........................8R-32
REAR WIPER & WASHER SYSTEM -
DIAGNOSIS AND TESTING.............8R-30
REAR WIPER & WASHER SYSTEM -
INSPECTION........................8R-33
REAR WIPER ARM - DESCRIPTION......8R-37
REAR WIPER ARM - INSTALLATION......8R-38
REAR WIPER ARM - OPERATION........8R-38
REAR WIPER ARM - REMOVAL.........8R-38
REAR WIPER BLADE - DESCRIPTION
.....8R-39
REAR WIPER BLADE - INSTALLATION
....8R-40
REAR WIPER BLADE - OPERATION
......8R-39
REAR WIPER BLADE - REMOVAL
........8R-40
REAR WIPER MOTOR - DESCRIPTION
....8R-41
REAR WIPER MOTOR - INSTALLATION
. . . 8R-42
REAR WIPER MOTOR - OPERATION
......8R-41
REAR WIPER MOTOR - REMOVAL
.......8R-42
REAR WIPERS/WASHERS -
DESCRIPTION
.......................8R-27
REAR WIPERS/WASHERS - OPERATION
. . 8R-29
REAR WIPER/WASHER SWITCH -
DESCRIPTION
.......................8R-43
REAR WIPER/WASHER SWITCH -
OPERATION
.........................8R-43
REARVIEW MIRROR SUPPORT BRACKET
- INSTALLATION
....................23-161RECEIVER LAMP BULB - INSTALLATION,
ASH ...............................8L-71
RECEIVER LAMP BULB - REMOVAL, ASH . . 8L-71
RECEIVER LAMP UNIT - INSTALLATION,
ASH ...............................8L-72
RECEIVER LAMP UNIT - REMOVAL, ASH . . 8L-72
RECIRC DOOR - INSTALLATION.........24-37
RECIRC DOOR - REMOVAL.............24-37
RECIRCULATION DOOR ACTUATOR -
INSTALLATION.......................24-26
RECIRCULATION DOOR ACTUATOR -
REMOVAL..........................24-26
RECLINER - FRONT - INSTALLATION,
SEAT BACK........................23-166
RECLINER - FRONT - REMOVAL, SEAT
BACK.............................23-166
RECOMMENDATIONS - STANDARD
PROCEDURE, HOISTING.................0-4
RECOVERY - STANDARD PROCEDURE,
REFRIGERANT.......................24-41
RECOVERY PRESS CONTAINER -
DESCRIPTION, COOLANT...............7-19
RECOVERY PRESS CONTAINER -
OPERATION, COOLANT.................7-19
REFACING - STANDARD PROCEDURE . . 9-26,9-34
REFERENCES - DESCRIPTION, TORQUE . . Intro.-7
REFILLING COOLING SYSTEM 3.7L
ENGINE - STANDARD PROCEDURE........7-12
REFRIGERANT - DESCRIPTION..........24-53
REFRIGERANT - OPERATION............24-53
REFRIGERANT HOSES/LINES/TUBES
PRECAUTIONS - CAUTION.............24-40
REFRIGERANT LINE - DESCRIPTION......24-38
REFRIGERANT OIL - DESCRIPTION......24-53
REFRIGERANT OIL - OPERATION........24-54
REFRIGERANT OIL LEVEL - STANDARD
PROCEDURE........................24-54
REFRIGERANT RECOVERY - STANDARD
PROCEDURE........................24-41
REFRIGERANT SYSTEM CHARGE -
STANDARD PROCEDURE...............24-41
REFRIGERANT SYSTEM EVACUATE -
STANDARD PROCEDURE...............24-41
REFRIGERANT SYSTEM SERVICE
EQUIPMENT - STANDARD PROCEDURE . . . 24-40
REFRIGERANT SYSTEM SERVICE PORT -
DESCRIPTION........................24-2
REFRIGERANT SYSTEM SERVICE PORT -
OPERATION..........................24-2
REGULATOR - DESCRIPTION, FUEL
PRESSURE.........................14-13
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-31
REGULATOR - ELECTRIC -
INSTALLATION, WINDOW.......23-126,23-134
REGULATOR - ELECTRIC - REMOVAL,
WINDOW....................23-126,23-134
REGULATOR - INSTALLATION, FUEL
PRESSURE.........................14-14
REGULATOR - MANUAL - INSTALLATION,
WINDOW....................23-126,23-133
REGULATOR - MANUAL - REMOVAL,
WINDOW....................23-126,23-133
REGULATOR - OPERATION, FUEL
PRESSURE.........................14-14
REGULATOR - OPERATION, VOLTAGE.....8F-31
REGULATOR - REMOVAL, FUEL
PRESSURE.........................14-14
REINFORCEMENT - INSTALLATION,
GRILLE OPENING...................23-142
REINFORCEMENT - REMOVAL, GRILLE
OPENING..........................23-142
RELAY - DESCRIPTION.............8W-97-13
RELAY - DESCRIPTION, A/C
COMPRESSOR CLUTCH...............24-15
RELAY - DESCRIPTION, AMPLIFIER
CHOKE..............................8A-3
RELAY - DESCRIPTION, BLOWER
MOTOR............................24-20
RELAY - DESCRIPTION, CLUTCH SWITCH
OVERRIDE...........................6-10
RELAY - DESCRIPTION, DAYTIME
RUNNING LAMP
.....................8L-20
RELAY - DESCRIPTION, DOOR LOCK
......8N-6
RELAY - DESCRIPTION, FRONT FOG
LAMP
..............................8L-22
RELAY - DESCRIPTION, FUEL PUMP
.....14-34
RELAY - DESCRIPTION, HEADLAMP
HIGH BEAM
.........................8L-33RELAY - DESCRIPTION, HEADLAMP LOW
BEAM..............................8L-39
RELAY - DESCRIPTION, PARK LAMP.....8L-54
RELAY - DESCRIPTION, REAR FOG LAMP . 8L-56
RELAY - DESCRIPTION, REAR WINDOW
DEFOGGER..........................8G-6
RELAY - DESCRIPTION, STARTER
MOTOR............................8F-41
RELAY - DESCRIPTION, TRAILER TOW....8L-61
RELAY - DESCRIPTION, TRANSMISSION
CONTROL.........................21-168
RELAY - DESCRIPTION, WIPER
HIGH/LOW..........................8R-23
RELAY - DESCRIPTION, WIPER ON/OFF . . . 8R-25
RELAY - DIAGNOSIS AND TESTING . . . 8W-97-13
RELAY - DIAGNOSIS AND TESTING,
AMPLIFIER CHOKE....................8A-4
RELAY - DIAGNOSIS AND TESTING,
BLOWER MOTOR....................24-21
RELAY - DIAGNOSIS AND TESTING,
COMPRESSOR CLUTCH...............24-15
RELAY - DIAGNOSIS AND TESTING,
DOOR LOCK.........................8N-6
RELAY - DIAGNOSIS AND TESTING,
FRONT FOG LAMP....................8L-23
RELAY - DIAGNOSIS AND TESTING,
FUEL PUMP.........................14-34
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP HIGH BEAM...............8L-34
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP LOW BEAM...............8L-40
RELAY - DIAGNOSIS AND TESTING,
HORN..............................8H-3
RELAY - DIAGNOSIS AND TESTING,
PARK LAMP.........................8L-55
RELAY - DIAGNOSIS AND TESTING,
REAR FOG LAMP.....................8L-57
RELAY - DIAGNOSIS AND TESTING,
REAR WINDOW DEFOGGER.............8G-6
RELAY - DIAGNOSIS AND TESTING,
STARTER ...........................8F-42
RELAY - DIAGNOSIS AND TESTING,
TRAILER TOW.......................8L-62
RELAY - DIAGNOSIS AND TESTING,
WIPER HIGH/LOW...................8R-24
RELAY - DIAGNOSIS AND TESTING,
WIPER ON/OFF......................8R-26
RELAY - INSTALLATION............8W-97-14
RELAY - INSTALLATION, A/C
COMPRESSOR CLUTCH...............24-16
RELAY - INSTALLATION, AMPLIFIER
CHOKE..............................8A-4
RELAY - INSTALLATION, BLOWER
MOTOR............................24-22
RELAY - INSTALLATION, CLUTCH
SWITCH OVERRIDE....................6-10
RELAY - INSTALLATION, DAYTIME
RUNNING LAMP.....................8L-21
RELAY - INSTALLATION, DOOR LOCK.....8N-7
RELAY - INSTALLATION, FRONT FOG
LAMP..............................8L-24
RELAY - INSTALLATION, FUEL PUMP.....14-34
RELAY - INSTALLATION, HEADLAMP
HIGH BEAM.........................8L-35
RELAY - INSTALLATION, HEADLAMP
LOW BEAM.........................8L-41
RELAY - INSTALLATION, HORN..........8H-3
RELAY - INSTALLATION, PARK LAMP.....8L-56
RELAY - INSTALLATION, REAR FOG
LAMP..............................8L-58
RELAY - INSTALLATION, REAR WINDOW
DEFOGGER..........................8G-7
RELAY - INSTALLATION, STARTER
MOTOR............................8F-43
RELAY - INSTALLATION, TRAILER TOW . . . 8L-64
RELAY - INSTALLATION, WIPER
HIGH/LOW..........................8R-24
RELAY - INSTALLATION, WIPER ON/OFF . . 8R-26
RELAY - OPERATION...............8W-97-13
RELAY - OPERATION, A/C COMPRESSOR
CLUTCH............................24-15
RELAY - OPERATION, AMPLIFIER CHOKE
. . . 8A-3
RELAY - OPERATION, BLOWER MOTOR
. . . 24-20
RELAY - OPERATION, CLUTCH SWITCH
OVERRIDE
...........................6-10
RELAY - OPERATION, DAYTIME
RUNNING LAMP
.....................8L-20
RELAY - OPERATION, DOOR LOCK
........8N-6
KJINDEX 21
Description Group-Page Description Group-Page Description Group-Page

VALVE - INSTALLATION, FLOW
MANAGEMENT.......................14-7
VALVE - INSTALLATION, FRONT CHECK....8R-9
VALVE - INSTALLATION, FUEL TANK
CHECK.............................14-28
VALVE - INSTALLATION, PCV...........25-32
VALVE - INSTALLATION, REAR CHECK....8R-35
VALVE - INSTALLATION, VACUUM CHECK . 24-28
VALVE - OPERATION, FLOW
MANAGEMENT.......................14-6
VALVE - OPERATION, FRONT CHECK......8R-9
VALVE - OPERATION, FUEL TANK CHECK . . 14-28
VALVE - OPERATION, HIGH PRESSURE
RELIEF.............................24-42
VALVE - OPERATION, PCV..............25-31
VALVE - OPERATION, REAR CHECK......8R-34
VALVE - OPERATION, SOLENOID SWITCH . 21-161
VALVE - OPERATION, VACUUM CHECK....24-28
VALVE - REMOVAL, FLOW
MANAGEMENT.......................14-6
VALVE - REMOVAL, FRONT CHECK.......8R-9
VALVE - REMOVAL, FUEL TANK CHECK . . . 14-28
VALVE - REMOVAL, PCV...............25-32
VALVE - REMOVAL, REAR CHECK.......8R-34
VALVE - REMOVAL, VACUUM CHECK.....24-28
VALVE BODY - ASSEMBLY............21-176
VALVE BODY - CLEANING.............21-175
VALVE BODY - DESCRIPTION............21-171
VALVE BODY - DISASSEMBLY..........21-173
VALVE BODY - INSPECTION...........21-175
VALVE BODY - INSTALLATION..........21-177
VALVE BODY - OPERATION............21-171
VALVE BODY - REMOVAL.............21-172
VALVE GUIDE SEALS - DESCRIPTION . . 9-29,9-38
VALVE GUIDES - DESCRIPTION......9-19,9-30
VALVE SPRINGS - DESCRIPTION.....9-29,9-38
VALVE SPRINGS - INSTALLATION.....9-29,9-38
VALVE SPRINGS - REMOVAL........9-29,9-38
VALVE TIMING - DESCRIPTION...........9-71
VALVE TIMING - OPERATION............9-71
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST.................9-28,9-36
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST.................9-27,9-35
VANITY LAMP BULB - INSTALLATION.....8L-84
VANITY LAMP BULB - REMOVAL........8L-83
VAPOR CANISTER - DESCRIPTION.......25-33
VAPOR CANISTER - INSTALLATION......25-33
VAPOR CANISTER - OPERATION.........25-33
VAPOR CANISTER - REMOVAL..........25-33
VARIATION ADJUSTMENT - STANDARD
PROCEDURE, COMPASS...............8M-3
VEHICLE EMISSION CONTROL
INFORMATION (VECI) LABEL -
DESCRIPTION......................Intro.-8
VEHICLE IDENTIFICATION NUMBER -
DESCRIPTION......................Intro.-8
VEHICLE SAFETY CERTIFICATION LABEL
- DESCRIPTION.....................Intro.-9
VEHICLE THEFT SECURITY -
DESCRIPTION........................8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-3
VEHICLE THEFT SECURITY SYSTEM -
DIAGNOSIS AND TESTING..............8Q-6
VERIFICATION TEST - STANDARD
PROCEDURE.........................8O-8
VIBRATION - DIAGNOSIS AND TESTING,
TIRE NOISE OR.......................22-8
VIBRATION DAMPER - INSTALLATION.....9-55
VIBRATION DAMPER - REMOVAL.........9-54
VIEW MIRROR - INSTALLATION, SIDE . . . 23-145
VIEW MIRROR - REMOVAL, REAR......23-161
VIEW MIRROR - REMOVAL, SIDE.......23-145
VISCOUS - CLEANING, RADIATOR - FAN . . . 7-29
VISCOUS - DESCRIPTION, RADIATOR -
FAN ................................7-27
VISCOUS - INSPECTION, RADIATOR -
FAN ................................7-29
VISCOUS - INSTALLATION, RADIATOR -
FAN
................................7-29
VISCOUS - OPERATION, RADIATOR -
FAN
................................7-27
VISCOUS - REMOVAL, RADIATOR - FAN
....7-28
VISCOUS FAN DRIVE - DIAGNOSIS AND
TESTING
............................7-28
VISOR - INSTALLATION, SUN
..........23-160VISOR - REMOVAL, SUN..............23-160
VISOR SUPPORT - INSTALLATION, SUN . . 23-160
VISOR SUPPORT - REMOVAL, SUN.....23-160
VOLT SUPPLIES - DESCRIPTION, 5......8E-13
VOLT SUPPLIES - OPERATION, 5........8E-15
VOLTAGE DROP - STANDARD
PROCEDURE, TESTING FOR A.......8W-01-10
VOLTAGE POTENTIAL - STANDARD
PROCEDURE, TESTING OF...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION....8F-31
VOLTAGE REGULATOR - OPERATION.....8F-31
VOLTAGE TEST - STANDARD
PROCEDURE, OPEN-CIRCUIT...........8F-12
VOLUME CHECK - STANDARD
PROCEDURE, OIL PUMP..............21-148
WAIT-TO-START INDICATOR -
DESCRIPTION.......................8J-35
WAIT-TO-START INDICATOR -
OPERATION.........................8J-35
WARNING - INSTALLATION............23-173
WARNING - REMOVAL...............23-173
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - SERVICE WARNINGS........24-39
WARNING - WINDSHIELD SAFETY
PRECAUTIONS......................23-173
WARNING, BRAKES - BASE..............5-2
WARNING, CLUTCH.....................6-2
WARNING, FRONT......................2-7
WARNING, REAR......................2-16
WARNING, RESTRAINT SYSTEM.........8O-5
WARNING SYSTEM - DESCRIPTION,
CHIME..............................8B-1
WARNING SYSTEM - DIAGNOSIS AND
TESTING, CHIME......................8B-6
WARNING SYSTEM - OPERATION,
CHIME..............................8B-2
WARNINGS, GENERAL..............8W-01-7
WARNINGS, WARNING - SAFETY
PRECAUTIONS........................23-1
WARNINGS, WARNING - SERVICE.......24-39
WASHER FLUID INDICATOR -
DESCRIPTION.......................8J-35
WASHER FLUID INDICATOR -
DIAGNOSIS AND TESTING..............8J-36
WASHER FLUID INDICATOR -
OPERATION.........................8J-36
WASHER FLUID LEVEL SWITCH -
DESCRIPTION.......................8R-17
WASHER FLUID LEVEL SWITCH -
INSTALLATION......................8R-18
WASHER FLUID LEVEL SWITCH -
OPERATION.........................8R-17
WASHER FLUID LEVEL SWITCH -
REMOVAL..........................8R-17
WASHER HOSES/TUBES - DESCRIPTION,
FRONT.............................8R-10
WASHER HOSES/TUBES - DESCRIPTION,
REAR..............................8R-35
WASHER HOSES/TUBES - OPERATION,
FRONT.............................8R-10
WASHER HOSES/TUBES - OPERATION,
REAR..............................8R-36
WASHER NOZZLE - DESCRIPTION,
FRONT.............................8R-11
WASHER NOZZLE - DESCRIPTION, REAR . 8R-36
WASHER NOZZLE - INSTALLATION,
FRONT.............................8R-11
WASHER NOZZLE - INSTALLATION,
REAR..............................8R-37
WASHER NOZZLE - OPERATION, FRONT . . 8R-11
WASHER NOZZLE - OPERATION, REAR . . . 8R-36
WASHER NOZZLE - REMOVAL, FRONT....8R-11
WASHER NOZZLE - REMOVAL, REAR....8R-36
WASHER PUMP/MOTOR - DESCRIPTION . . 8R-18
WASHER PUMP/MOTOR - INSTALLATION . 8R-20
WASHER PUMP/MOTOR - OPERATION . . . 8R-19
WASHER PUMP/MOTOR - REMOVAL.....8R-19
WASHER RESERVOIR - DESCRIPTION....8R-21
WASHER RESERVOIR - INSTALLATION . . . 8R-22
WASHER RESERVOIR - OPERATION
......8R-21
WASHER RESERVOIR - REMOVAL
.......8R-21
WASHER SYSTEM - CLEANING, FRONT
WIPER
..............................8R-7
WASHER SYSTEM - CLEANING, REAR
WIPER
.............................8R-32
WASHER SYSTEM - DIAGNOSIS AND
TESTING, FRONT WIPER
...............8R-6WASHER SYSTEM - DIAGNOSIS AND
TESTING, REAR WIPER...............8R-30
WASHER SYSTEM - INSPECTION, FRONT
WIPER..............................8R-7
WASHER SYSTEM - INSPECTION, REAR
WIPER.............................8R-33
WATER DRAINAGE AND WIND NOISE
DIAGNOSIS, DIAGNOSIS AND TESTING . . 23-176
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-2
WATER PUMP - DESCRIPTION...........7-29
WATER PUMP - OPERATION.............7-30
WATERDAM - INSTALLATION....23-126,23-133
WATERDAM - REMOVAL........23-126,23-133
WATER-IN-FUEL INDICATOR -
DESCRIPTION.......................8J-37
WATER-IN-FUEL INDICATOR -
OPERATION.........................8J-37
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD......................22-8
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE.......................22-8
WEAR, STANDARD PROCEDURE -
MEASURING TIMING CHAIN.............9-71
WEATHERSTRIP - INSTALLATION, COWL . 23-185
WEATHERSTRIP - INSTALLATION, DOOR
LOWER...........................23-186
WEATHERSTRIP - INSTALLATION, DOOR
PRIMARY..........................23-185
WEATHERSTRIP - INSTALLATION,
SWING GATE BELTLINE...............23-186
WEATHERSTRIP - INSTALLATION,
SWING GATE OPENING...............23-186
WEATHERSTRIP - REMOVAL, COWL.....23-185
WEATHERSTRIP - REMOVAL, DOOR
LOWER...........................23-186
WEATHERSTRIP - REMOVAL, DOOR
PRIMARY..........................23-185
WEATHERSTRIP - REMOVAL, SWING
GATE BELTLINE.....................23-186
WEATHERSTRIP - REMOVAL, SWING
GATE OPENING.....................23-186
WEATHERSTRIP/RETAINER -
INSTALLATION, SIDE RAIL............23-186
WEATHERSTRIP/RETAINER -
INSTALLATION, WINDSHIELD A-PILLAR . . 23-187
WEATHERSTRIP/RETAINER - REMOVAL,
SIDE RAIL.........................23-186
WEATHERSTRIP/RETAINER - REMOVAL,
WINDSHIELD A-PILLAR...............23-186
WELD AND STRUCTURAL ADHESIVE
LOCATIONS - SPECIFICATIONS...........23-9
WHEEL - INSTALLATION, STEERING......19-12
WHEEL - REMOVAL, STEERING.........19-12
WHEEL ALIGNMENT - DESCRIPTION.......2-3
WHEEL ALIGNMENT - OPERATION.........2-3
WHEEL BALANCING - STANDARD
PROCEDURE.........................22-4
WHEEL CYLINDERS - ASSEMBLY.........5-29
WHEEL CYLINDERS - CLEANING.........5-28
WHEEL CYLINDERS - DISASSEMBLY......5-28
WHEEL CYLINDERS - INSPECTION........5-29
WHEEL CYLINDERS - INSTALLATION......5-29
WHEEL CYLINDERS - REMOVAL..........5-28
WHEEL MOUNTING - STANDARD
PROCEDURE........................22-10
WHEEL OPENING FLARE MOLDINGS -
INSTALLATION, FRONT...............23-145
WHEEL OPENING FLARE MOLDINGS -
INSTALLATION, REAR................23-145
WHEEL OPENING FLARE MOLDINGS -
REMOVAL, FRONT...................23-145
WHEEL OPENING FLARE MOLDINGS -
REMOVAL, REAR....................23-145
WHEEL REPLACEMENT - STANDARD
PROCEDURE........................22-10
WHEEL RUNOUT - DIAGNOSIS AND
TESTING, TIRES......................22-1
WHEEL SPEED SENSOR -
INSTALLATION, FRONT
.................5-34
WHEEL SPEED SENSOR -
INSTALLATION, REAR
..................5-35
WHEEL SPEED SENSOR - REMOVAL,
FRONT
..............................5-34
WHEEL SPEED SENSOR - REMOVAL,
REAR
...............................5-35
WHEELHOUSE SPLASH SHIELD -
INSTALLATION, FRONT
...............23-143
KJINDEX 29
Description Group-Page Description Group-Page Description Group-Page