2002 JEEP LIBERTY relays

WARNING: BEFORE PROCEEDING TO NEXT STEP,
NOTE THE FUEL PUMP WILL BE ACTIVATED AND
SYSTEM PRESSURE WILL BE PRESENT. THIS WILL
OCCUR AFTER CONNECTING TEST LEADS FROM
LCS ADAPTER INTO FUEL PUMP RELAY CAVITIES.
THE FUEL PUMP WILL OPERATE EVEN WITH IGNI-
TION KEY IN OFF POSITION. BEFORE ATTACHING
TEST LEADS, BE SURE ALL FUEL LINES AND
FUEL SYSTEM COMPONENTS ARE CONNECTED.
CAUTION: To prevent possible damage to the vehi-
cle electrical system and LCS adapter, the test
leads must be connected into relay cavities exactly
as shown in following steps.
Depending upon vehicle model, year or engine con-
figuration, three different types of relays may be
used: Type-1, type-2 and type±3.
(14) If equipped withtype±1 relay(Fig. 22),
attach test leads from LCS adapter into PDC relay
cavities number 30 and 87. For location of these cav-
ities, refer to numbers stamped to bottom of relay
(Fig. 22).
(15) If equipped withtype±2 relay(Fig. 23),
attach test leads from LCS adapter into PDC relay
cavities number 30 and 87. For location of these cav-
ities, refer to numbers stamped to bottom of relay
(Fig. 23).
(16) If equipped withtype±3 relay(Fig. 24),
attach test leads from LCS adapter into PDC relay
cavities number 3 and 5. For location of these cavi-
ties, refer to numbers stamped to bottom of relay
(Fig. 24).
Fig. 22 FUEL PUMP RELAY - TYPE 1
Fig. 23 FUEL PUMP RELAY - TYPE 2
TERMINAL LEGEND
NUMBER IDENTIFICATION
30 COMMON FEED
85 COIL GROUND
86 COIL BATTERY
87 NORMALLY OPEN
87A NORMALLY CLOSED
Fig. 24 FUEL PUMP RELAY - TYPE 3
TERMINAL LEGEND
NUMBER IDENTIFICATION
1 COIL BATTERY
2 COIL GROUND
3 COMMON FEED
4 NORMALLY CLOSED
5 NORMALLY OPEN
KJFUEL DELIVERY 14 - 17
FUEL PUMP (Continued)

(M)Malfunction Indicator Lamp (MIL) illuminated during engine operation if this DTC was recorded
(depending if required by CARB and/or EPA). MIL is displayed as an engine icon on instrument panel.
(G)Generator lamp illuminated
Generic Scan
Tool P-CodeDRB Scan Tool Display Brief Description of DTC
P1478 Battery Temp Sensor Volts Out of
LimitInternal temperature sensor input voltage out of an
acceptable range.
P1479 Transmission Fan Relay Circuit An open or shorted condition detected in the transmission
fan relay circuit.
P1480 PCV Solenoid Circuit An open or shorted condition detected in the PCV
solenoid circuit.
P1481 EATX RPM Pulse Perf EATX RPM pulse generator signal for misfire detection
does not correlate with expected value.
P1482 Catalyst Temperature Sensor Circuit
Shorted LowCatalyst temperature sensor circuit shorted low.
P1483 Catalyst Temperature Sensor Circuit
Shorted High.Catalyst temperature sensor circuit shorted high.
P1484 Catalytic Converter Overheat
DetectedA catalyst overheat condition has been detected by the
catalyst temperature sensor.
P1485 Air Injection Solenoid Circuit An open or shorted condition detected in the air assist
solenoid circuit.
P1486 Evap Leak Monitor Pinched Hose
FoundLDP has detected a pinched hose in the evaporative hose
system.
P1487 Hi Speed Rad Fan CTRL Relay
CircuitAn open or shorted condition detected in the control
circuit of the #2 high speed radiator fan control relay.
P1488 Auxiliary 5 Volt Supply Output Too
LowAuxiliary 5 volt sensor feed is sensed to be below an
acceptable limit.
P1488 5 Volt Supply Voltage Low Sensor supply voltage for ECM sensors is too low.
P1489 High Speed Fan CTRL Relay Circuit An open or shorted condition detected in the control
circuit of the high speed radiator fan control relay.
P1490 Low Speed Fan CTRL Relay Circuit An open or shorted condition detected in control circuit of
the low speed radiator fan control relay.
P1491 Rad Fan Control Relay Circuit An open or shorted condition detected in the radiator fan
control relay control circuit. This includes PWM solid state
relays.
P1492 Ambient/Batt Temp Sen Volts Too
HighExternal temperature sensor input above acceptable
voltage.
P1492 (M) Ambient/Batt Temp Sensor Volts Too
HighBattery temperature sensor input voltage above an
acceptable range.
P1493 (M) Ambient/Batt Temp Sen Volts Too
LowExternal temperature sensor input below acceptable
voltage.
P1493 (M) Ambient/Batt Temp Sen Volts Too
LowBattery temperature sensor input voltage below an
acceptable range.
P1494 (M) Leak Detection Pump Sw or
Mechanical FaultIncorrect input state detected for the Leak Detection
Pump (LDP) pressure switch.
P1495 Leak Detection Pump Solenoid
CircuitAn open or shorted condition detected in the Leak
Detection Pump (LDP) solenoid circuit.
P1496 5 Volt Supply, Output Too Low 5 volt sensor feed is sensed to be below an acceptable
limit. ( less than 4v for 4 sec )
KJEMISSIONS CONTROL 25 - 13
EMISSIONS CONTROL (Continued)

ANTENNA BODY & CABLE - OPERATION . . . 8A-5
ANTENNA BODY & CABLE - REMOVAL.....8A-6
ANTENNA BODY AND CABLE -
DIAGNOSIS AND TESTING..............8A-5
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL..................8A-8
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL..................8A-7
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER.......................8E-10
ANTILOCK BRAKE - REMOVAL,
CONTROLLER.......................8E-10
ANTILOCK BRAKING SYSTEM -
DIAGNOSIS AND TESTING..............5-33
A-PILLAR SEAL - INSTALLATION.......23-185
A-PILLAR SEAL - REMOVAL...........23-185
A-PILLAR TRIM AND GRAB HANDLE -
INSTALLATION......................23-156
A-PILLAR TRIM AND GRAB HANDLE -
REMOVAL.........................23-156
A-PILLAR WEATHERSTRIP/RETAINER -
INSTALLATION, WINDSHIELD..........23-187
A-PILLAR WEATHERSTRIP/RETAINER -
REMOVAL, WINDSHIELD..............23-186
APPLICATION TABLE, SPECIFICATIONS -
A/C ................................24-9
AREA LEAKS - DIAGNOSIS AND
TESTING, REAR SEAL..................9-61
ARM - DESCRIPTION, FRONT WIPER.....8R-12
ARM - DESCRIPTION, LOWER CONTROL . . . 2-21
ARM - DESCRIPTION, REAR WIPER......8R-37
ARM - DESCRIPTION, ROCKER......9-29,9-37
ARM - INSTALLATION, FRONT WIPER....8R-13
ARM - INSTALLATION, LOWER CONTROL . . 2-10,
2-21
ARM - INSTALLATION, REAR WIPER.....8R-38
ARM - INSTALLATION, ROCKER..........9-37
ARM - INSTALLATION, UPPER CONTROL . . . 2-21
ARM - OPERATION, FRONT WIPER......8R-12
ARM - OPERATION, LOWER CONTROL.....2-21
ARM - OPERATION, REAR WIPER.......8R-38
ARM - REMOVAL, FRONT WIPER........8R-12
ARM - REMOVAL, LOWER CONTROL . . 2-10,2-21
ARM - REMOVAL, REAR WIPER.........8R-38
ARM - REMOVAL, ROCKER..............9-37
ARM - REMOVAL, UPPER CONTROL......2-20
ARM, BUSHINGS, AND BALL JOINT -
DESCRIPTION, UPPER SUSPENSION......2-20
ARM, BUSHINGS, AND BALL JOINT -
OPERATION, UPPER SUSPENSION........2-20
ARM PARK RAMP - INSTALLATION,
WIPER.............................8R-43
ARM PARK RAMP - REMOVAL, WIPER . . . 8R-43
ASD AND FUEL PUMP RELAYS -
DIAGNOSIS AND TESTING...............8I-4
ASD SENSE - PCM INPUT - OPERATION....8I-4
ASH RECEIVER LAMP BULB -
INSTALLATION.......................8L-71
ASH RECEIVER LAMP BULB - REMOVAL . . 8L-71
ASH RECEIVER LAMP UNIT -
INSTALLATION.......................8L-72
ASH RECEIVER LAMP UNIT - REMOVAL . . 8L-72
ASSEMBLY - ASSEMBLY, INPUT CLUTCH . 21-138
ASSEMBLY - DESCRIPTION, INPUT
CLUTCH...........................21-133
ASSEMBLY - DESCRIPTION,
TRANSMISSION SOLENOID/TRS........21-169
ASSEMBLY - DISASSEMBLY, INPUT
CLUTCH...........................21-135
ASSEMBLY - INSTALLATION.........8W-97-11
ASSEMBLY - INSTALLATION, GUIDE.....23-179
ASSEMBLY - INSTALLATION,
INSTRUMENT PANEL.................23-151
ASSEMBLY - INSTALLATION, MODULE . . . 23-181
ASSEMBLY - INSTALLATION,
TRANSMISSION SOLENOID/TRS........21-170
ASSEMBLY - OPERATION, INPUT
CLUTCH...........................21-135
ASSEMBLY - OPERATION,
TRANSMISSION SOLENOID/TRS........21-169
ASSEMBLY - POWER DISTRIBUTION
CENTER ASSEMBLY
...............8W-97-10
ASSEMBLY - REMOVAL, GUIDE
........23-179
ASSEMBLY - REMOVAL, INSTRUMENT
PANEL
............................23-149
ASSEMBLY - REMOVAL, MODULE
......23-181
ASSEMBLY - REMOVAL, TRANSMISSION
SOLENOID/TRS
.....................21-170ASSEMBLY, 4C RETAINER/BULKHEAD....21-123
ASSEMBLY, ASSEMBLY - POWER
DISTRIBUTION CENTER............8W-97-10
ASSEMBLY, DIAGNOSIS AND TESTING....21-90
ASSEMBLY, DIFFERENTIAL.........3-105,3-41
ASSEMBLY, DIFFERENTIAL - TRAC-LOK . . . 3-109,
3-77
ASSEMBLY, DISC BRAKE CALIPERS.......5-16
ASSEMBLY, HVAC HOUSING............24-34
ASSEMBLY, INPUT CLUTCH ASSEMBLY . . 21-138
ASSEMBLY, INSTRUMENT CLUSTER......8J-10
ASSEMBLY, LOW/REVERSE CLUTCH.....21-146
ASSEMBLY, MANUAL - NV1500.........21-13
ASSEMBLY, MANUAL - NV3550.........21-48
ASSEMBLY, OIL PUMP.................9-67
ASSEMBLY, OIL PUMP...............21-151
ASSEMBLY, PLANETARY GEARTRAIN....21-160
ASSEMBLY, SINGLE CARDAN
UNIVERSAL JOINTS....................3-9
ASSEMBLY, TRANSFER CASE - NV231 . . . 21-194
ASSEMBLY, TRANSFER CASE - NV242 . . . 21-230
ASSEMBLY, VALVE BODY.............21-176
ASSEMBLY, WHEEL CYLINDERS..........5-29
ASSEMBLY WINDOW DEFOGGER
FUNCTION - DIAGNOSIS AND TESTING,
REAR HVAC CONTROL.................8G-9
ASSIST HANDLE - INSTALLATION.......23-157
ASSIST HANDLE - REMOVAL............23-157
AUDIO - DESCRIPTION.................8A-1
AUDIO - DIAGNOSIS AND TESTING.......8A-2
AUDIO - OPERATION...................8A-1
AUTOMATIC TRANSMISSION - 45RFE -
DESCRIPTION.......................21-76
AUTOMATIC TRANSMISSION - 45RFE -
OPERATION.........................21-77
AUTOMATIC TRANSMISSION -
DIAGNOSIS AND TESTING.............21-77
AUTOMATIC TRANSMISSION FLUID -
DESCRIPTION.........................0-2
AUTOMATIC TRANSMISSION FLUID -
OPERATION...........................0-4
AXLE - 186FIA - ADJUSTMENTS, FRONT . . . 3-25
AXLE - 186FIA - DESCRIPTION, FRONT....3-19
AXLE - 186FIA - INSTALLATION, FRONT....3-24
AXLE - 186FIA - OPERATION, FRONT......3-19
AXLE - 186FIA - REMOVAL, FRONT.......3-24
AXLE - 198RBI - DESCRIPTION, REAR.....3-49
AXLE - 198RBI - INSTALLATION, REAR....3-54
AXLE - 198RBI - OPERATION, REAR.......3-49
AXLE - 198RBI - REMOVAL, REAR........3-54
AXLE - 8 1/4 - ADJUSTMENTS, REAR.....3-92
AXLE - 8 1/4 - DESCRIPTION, REAR......3-86
AXLE - 8 1/4 - INSTALLATION, REAR......3-91
AXLE - 8 1/4 - OPERATION, REAR........3-86
AXLE - 8 1/4 - REMOVAL, REAR..........3-91
AXLE - DESCRIPTION...................0-2
AXLE - DIAGNOSIS AND TESTING....3-20,3-51,
3-88
AXLE - INSTALLATION, 198 RBI..........5-28
AXLE - INSTALLATION, 8 1/4............5-28
AXLE - REMOVAL, 198 RBI..............5-27
AXLE - REMOVAL, 8 1/4................5-27
AXLE - SPECIFICATIONS, FRONT.........3-33
AXLE - SPECIFICATIONS, REAR..........3-62
AXLE BEARINGS - INSTALLATION....3-102,3-38
AXLE BEARINGS - REMOVAL.......3-102,3-38
AXLE BEARING/SEAL - INSTALLATION.....3-67
AXLE BEARING/SEAL - REMOVAL.........3-66
AXLE SHAFT SEALS - INSTALLATION . 3-102,3-38
AXLE SHAFT SEALS - REMOVAL....3-101,3-37
AXLE SHAFTS - INSTALLATION . . 3-101,3-37,3-65
AXLE SHAFTS - REMOVAL.....3-101,3-37,3-65
AXLE, SPECIAL TOOLS - 8 1/4 ...........3-98
AXLE, SPECIAL TOOLS - FRONT..........3-34
AXLE, SPECIAL TOOLS - REAR...........3-63
AXLE, SPECIFICATIONS - REAR..........3-98
BACK - FRONT - INSTALLATION, SEAT . . . 23-166
BACK - FRONT - REMOVAL, SEAT.......23-166
BACK - REAR - INSTALLATION, SEAT....23-168
BACK - REAR - REMOVAL, SEAT.......23-168
BACK COVER - FRONT - INSTALLATION,
SEAT
.............................23-167
BACK COVER - FRONT - REMOVAL, SEAT
. 23-166
BACK COVER - REAR - INSTALLATION,
SEAT
.............................23-169
BACK COVER - REAR - REMOVAL, SEAT
. 23-169
BACK CUSHION - FRONT -
INSTALLATION, SEAT
.................23-167BACK CUSHION - FRONT - REMOVAL,
SEAT .............................23-167
BACK CUSHION - REAR - INSTALLATION,
SEAT .............................23-170
BACK CUSHION - REAR - REMOVAL,
SEAT .............................23-170
BACK FRAME - REAR - INSTALLATION,
SEAT .............................23-171
BACK FRAME - REAR - REMOVAL, SEAT . 23-171
BACK LATCH / LOCK - INSTALLATION,
FOLDING REAR SEAT................23-170
BACK LATCH / LOCK - REMOVAL,
FOLDING REAR SEAT................23-170
BACK LATCH STRIKER - INSTALLATION,
REAR SEAT........................23-171
BACK LATCH STRIKER - REMOVAL,
REAR SEAT........................23-170
BACK RECLINER - FRONT -
INSTALLATION, SEAT.................23-166
BACK RECLINER - FRONT - REMOVAL,
SEAT .............................23-166
BACKUP LAMP SWITCH - DESCRIPTION . . 8L-15
BACKUP LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-15
BACKUP LAMP SWITCH - OPERATION....8L-15
BAFFLE SEAL - INSTALLATION,
COWL/PLENUM WINDOW.............23-187
BAFFLE SEAL - REMOVAL, COWL/
PLENUM WINDOW..................23-187
BALANCE SHAFT - INSTALLATION........9-74
BALANCE SHAFT - REMOVAL............9-74
BALANCING - STANDARD PROCEDURE,
WHEEL.............................22-4
BALL JOINT - DESCRIPTION, UPPER
SUSPENSION ARM, BUSHINGS..........2-20
BALL JOINT - DIAGNOSIS AND TESTING,
LOWER.............................2-10
BALL JOINT - INSTALLATION, UPPER.....2-20
BALL JOINT - OPERATION, UPPER
SUSPENSION ARM, BUSHINGS..........2-20
BALL JOINT - REMOVAL, UPPER.........2-20
BAR - INSTALLATION, STABILIZER....2-14,2-19
BAR - REMOVAL, STABILIZER.......2-14,2-19
BAR BUSHINGS - INSTALLATION,
STABILIZER...........................2-9
BAR BUSHINGS - REMOVAL, STABILIZER . . . 2-9
BARRELS - INSTALLATION, PANEL
OUTLET............................24-29
BARRELS - REMOVAL, PANEL OUTLET . . . 24-29
BASE - DESCRIPTION, BRAKES...........5-2
BASE - WARNING, BRAKES..............5-2
BASE BRAKE SYSTEM - DIAGNOSIS AND
TESTING.............................5-3
BASE BRAKES, SPECIAL TOOLS...........5-7
BASE COAT/CLEAR COAT FINISH -
DESCRIPTION......................23-162
BATTERIES - STANDARD PROCEDURE,
RKE TRANSMITTER...................8N-8
BATTERY - DESCRIPTION...............8F-7
BATTERY - DIAGNOSIS AND TESTING.....8F-8
BATTERY CABLES - DESCRIPTION.......8F-18
BATTERY CABLES - DIAGNOSIS AND
TESTING...........................8F-19
BATTERY CABLES - OPERATION.........8F-18
BATTERY CHARGING - STANDARD
PROCEDURE.........................8F-8
BATTERY HOLDDOWN - DESCRIPTION....8F-17
BATTERY HOLDDOWN - INSTALLATION . . . 8F-17
BATTERY HOLDDOWN - OPERATION.....8F-17
BATTERY HOLDDOWN - REMOVAL.......8F-17
BATTERY SYSTEM - CLEANING...........8F-5
BATTERY SYSTEM - DESCRIPTION........8F-1
BATTERY SYSTEM - DIAGNOSIS AND
TESTING............................8F-2
BATTERY SYSTEM - INSPECTION.........8F-6
BATTERY SYSTEM - OPERATION.........8F-2
BATTERY SYSTEM - SPECIAL TOOLS......8F-7
BATTERY SYSTEM - SPECIFICATIONS......8F-6
BATTERY TEMPERATURE SENSOR -
DESCRIPTION.......................8F-24
BATTERY TEMPERATURE SENSOR -
INSTALLATION
.......................8F-24
BATTERY TEMPERATURE SENSOR -
OPERATION
.........................8F-24
BATTERY TEMPERATURE SENSOR -
REMOVAL
..........................8F-24
BATTERY TRAY - DESCRIPTION
.........8F-21
BATTERY TRAY - INSTALLATION
.........8F-21
2 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

FUEL PRESSURE REGULATOR -
DESCRIPTION.......................14-13
FUEL PRESSURE REGULATOR -
INSTALLATION.......................14-14
FUEL PRESSURE REGULATOR -
OPERATION.........................14-14
FUEL PRESSURE REGULATOR -
REMOVAL..........................14-14
FUEL PUMP - DESCRIPTION............14-15
FUEL PUMP - OPERATION.............14-15
FUEL PUMP AMPERAGE TEST -
DIAGNOSIS AND TESTING.............14-16
FUEL PUMP CAPACITY TEST -
DIAGNOSIS AND TESTING.............14-15
FUEL PUMP MODULE - DESCRIPTION....14-18
FUEL PUMP MODULE - INSTALLATION . . . 14-19
FUEL PUMP MODULE - OPERATION......14-18
FUEL PUMP MODULE - REMOVAL.......14-18
FUEL PUMP PRESSURE TEST -
DIAGNOSIS AND TESTING.............14-15
FUEL PUMP RELAY - DESCRIPTION......14-34
FUEL PUMP RELAY - DIAGNOSIS AND
TESTING...........................14-34
FUEL PUMP RELAY - INSTALLATION.....14-34
FUEL PUMP RELAY - OPERATION........14-34
FUEL PUMP RELAY - REMOVAL.........14-34
FUEL PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD........................8I-4
FUEL RAIL - DESCRIPTION.............14-21
FUEL RAIL - INSTALLATION..............14-24
FUEL RAIL - OPERATION...............14-21
FUEL RAIL - REMOVAL................14-22
FUEL SYSTEM PRESSURE RELEASE -
STANDARD PROCEDURE................14-4
FUEL SYSTEM PRESSURE,
SPECIFICATIONS......................14-5
FUEL SYSTEM, SPECIAL TOOLS..........14-6
FUEL TANK - DESCRIPTION............14-24
FUEL TANK - INSTALLATION............14-27
FUEL TANK - OPERATION..............14-24
FUEL TANK - REMOVAL...............14-25
FUEL TANK CHECK VALVE -
DESCRIPTION.......................14-28
FUEL TANK CHECK VALVE -
INSTALLATION.......................14-28
FUEL TANK CHECK VALVE - OPERATION . . 14-28
FUEL TANK CHECK VALVE - REMOVAL....14-28
FUEL TANK SKID PLATE - INSTALLATION . . . 13-9
FUEL TANK SKID PLATE - REMOVAL......13-9
FULL TIME INDICATOR - DESCRIPTION . . . 8J-29
FULL TIME INDICATOR - OPERATION.....8J-30
FUNCTION - DIAGNOSIS AND TESTING,
REAR HVAC CONTROL ASSEMBLY
WINDOW DEFOGGER..................8G-9
FUNCTIONS - DESCRIPTION, CIRCUIT . . 8W-01-6
FUSE - DESCRIPTION, IOD...........8W-97-3
FUSE - INSTALLATION, IOD..........8W-97-3
FUSE - OPERATION, IOD.............8W-97-3
FUSE - REMOVAL, IOD..............8W-97-3
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON.......8W-01-9
GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE AND OIL.....9-10
GAP AND FLUSH - SPECIFICATIONS.....23-116
GAS ENGINES - GENERATOR RATINGS....8F-23
GAS POWERED - STARTER MOTOR......8F-39
GAS POWERED - TORQUE
.............8F-38
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD
..................9-19,9-30
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE
.........9-9
GATE - INSTALLATION, SWING
.........23-138
GATE - REMOVAL, SWING
............23-138
GATE AJAR INDICATOR - DESCRIPTION
. . . 8J-20
GATE AJAR INDICATOR - OPERATION
.....8J-20
GATE BELTLINE WEATHERSTRIP -
INSTALLATION, SWING
...............23-186
GATE BELTLINE WEATHERSTRIP -
REMOVAL, SWING
...................23-186
GATE OPENING WEATHERSTRIP -
INSTALLATION, SWING
...............23-186
GATE OPENING WEATHERSTRIP -
REMOVAL, SWING
...................23-186
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE
......................8J-18
GAUGE - DESCRIPTION, FUEL
...........8J-19GAUGE - OPERATION, ENGINE
TEMPERATURE......................8J-18
GAUGE - OPERATION, FUEL............8J-20
GEAR - DESCRIPTION.................19-13
GEAR - INSTALLATION, PINION
GEAR/RING..........................3-46
GEAR - OPERATION...................19-13
GEAR - REMOVAL, PINION GEAR/RING....3-44
GEAR/RING GEAR - INSTALLATION,
PINION.............................3-46
GEAR/RING GEAR - REMOVAL, PINION....3-44
GEAR/RING GEAR/TONE RING -
INSTALLATION, PINION............3-112,3-82
GEAR/RING GEAR/TONE RING -
REMOVAL, PINION...............3-110,3-79
GEARSHIFT CABLE - ADJUSTMENTS....21-130
GEARSHIFT CABLE - DIAGNOSIS AND
TESTING..........................21-128
GEARSHIFT CABLE - INSTALLATION.....21-129
GEARSHIFT CABLE - REMOVAL........21-128
GEAR/TONE RING - INSTALLATION,
PINION GEAR/RING...............3-112,3-82
GEAR/TONE RING - REMOVAL, PINION
GEAR/RING.....................3-110,3-79
GEARTRAIN - ASSEMBLY, PLANETARY . . . 21-160
GEARTRAIN - CLEANING, PLANETARY . . . 21-159
GEARTRAIN - DESCRIPTION,
PLANETARY........................21-157
GEARTRAIN - DISASSEMBLY,
PLANETARY........................21-159
GEARTRAIN - INSPECTION, PLANETARY . 21-159
GEARTRAIN - OPERATION, PLANETARY . . 21-157
GENERAL - WARNINGS.............8W-01-7
GENERATOR - DESCRIPTION...........8F-25
GENERATOR - INSTALLATION...........8F-26
GENERATOR - OPERATION.............8F-25
GENERATOR - REMOVAL...............8F-25
GENERATOR DECOUPLER - DIAGNOSIS
AND TESTING.......................8F-27
GENERATOR DECOUPLER PULLEY -
DESCRIPTION.......................8F-26
GENERATOR DECOUPLER PULLEY -
INSTALLATION.......................8F-30
GENERATOR DECOUPLER PULLEY -
OPERATION.........................8F-27
GENERATOR DECOUPLER PULLEY -
REMOVAL..........................8F-27
GENERATOR RATINGS, GAS ENGINES....8F-23
GLASS - INSTALLATION, DOOR . . 23-122,23-129,
23-172
GLASS - INSTALLATION, FLIP-UP.......23-136
GLASS - REMOVAL, DOOR......23-122,23-129,
23-172
GLASS - REMOVAL, FLIP-UP..........23-136
GLASS AJAR INDICATOR - DESCRIPTION . . 8J-21
GLASS AJAR INDICATOR - OPERATION . . . 8J-21
GLASS AJAR SWITCH - DESCRIPTION,
FLIP-UP............................8L-77
GLASS AJAR SWITCH - OPERATION,
FLIP-UP............................8L-77
GLASS HEATING GRID REPAIR -
STANDARD PROCEDURE, REAR..........8G-4
GLASS LATCH - INSTALLATION, FLIP-UP . 23-136
GLASS LATCH - REMOVAL, FLIP-UP.....23-136
GLASS PANEL - INSTALLATION........23-178
GLASS PANEL - REMOVAL............23-178
GLASS PANEL ADJUSTMENT,
ADJUSTMENTS - SUNROOF...........23-178
GLASS PANEL SEAL - INSTALLATION
....23-178
GLASS PANEL SEAL - REMOVAL
.......23-178
GLASS RELEASE SWITCH - DIAGNOSIS
AND TESTING, FLIP-UP
................8N-5
GLASS RUN CHANNEL - INSTALLATION
. 23-123,
23-130
GLASS RUN CHANNEL - REMOVAL
.....23-123,
23-130
GLASS SUPPORT CYLINDER -
INSTALLATION, FLIP-UP
..............23-139
GLASS SUPPORT CYLINDER -
REMOVAL, FLIP-UP
..................23-139
GLOVE BOX - INSTALLATION
..........23-148
GLOVE BOX - REMOVAL
..............23-148
GLOVE BOX LATCH - INSTALLATION
....23-148
GLOVE BOX LATCH - REMOVAL
........23-148
GLOVE BOX LATCH STRIKER -
INSTALLATION
......................23-149
GLOVE BOX LATCH STRIKER - REMOVAL
. 23-148GRAB HANDLE - INSTALLATION,
A-PILLAR TRIM.....................23-156
GRAB HANDLE - REMOVAL, A-PILLAR
TRIM.............................23-156
GRID - DESCRIPTION, REAR WINDOW
DEFOGGER..........................8G-5
GRID - DIAGNOSIS AND TESTING, REAR
WINDOW DEFOGGER..................8G-5
GRID - OPERATION, REAR WINDOW
DEFOGGER..........................8G-5
GRID REPAIR - STANDARD PROCEDURE,
REAR GLASS HEATING.................8G-4
GRILLE - INSTALLATION..............23-142
GRILLE - INSTALLATION, COWL........23-140
GRILLE - REMOVAL..................23-142
GRILLE - REMOVAL, COWL...........23-140
GRILLE OPENING REINFORCEMENT -
INSTALLATION......................23-142
GRILLE OPENING REINFORCEMENT -
REMOVAL.........................23-142
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO..............................8W-01-9
GROUND STRAP - DESCRIPTION, RADIO
NOISE SUPPRESSION..................8A-9
GROUND STRAP - INSTALLATION,
RADIO NOISE SUPPRESSION...........8A-11
GROUND STRAP - OPERATION, RADIO
NOISE SUPPRESSION.................8A-10
GROUND STRAP - REMOVAL, RADIO
NOISE SUPPRESSION.................8A-10
GROUNDS - DESCRIPTION, POWER......8E-13
GUARD - DESCRIPTION, THERMAL......8F-20
GUARD - INSTALLATION, THERMAL......8F-20
GUARD - OPERATION, THERMAL........8F-20
GUARD - REMOVAL, THERMAL..........8F-20
GUIDE ASSEMBLY - INSTALLATION.....23-179
GUIDE ASSEMBLY - REMOVAL.........23-179
GUIDE SEALS - DESCRIPTION, VALVE . 9-29,9-38
GUIDES - DESCRIPTION, VALVE......9-19,9-30
HALF SHAFT - CAUTION................3-10
HALF SHAFT - DIAGNOSIS AND TESTING . . 3-10
HALF SHAFT - INSTALLATION............3-11
HALF SHAFT - REMOVAL...............3-10
HALF SHAFT, SPECIFICATIONS...........3-11
HANDLE - INSTALLATION, A-PILLAR
TRIM AND GRAB....................23-156
HANDLE - INSTALLATION, ASSIST......23-157
HANDLE - INSTALLATION, EXTERIOR . . . 23-123,
23-130,23-136
HANDLE - INSTALLATION, LATCH
RELEASE..........................23-120
HANDLE - REMOVAL, A-PILLAR TRIM
AND GRAB.........................23-156
HANDLE - REMOVAL, ASSIST..........23-157
HANDLE - REMOVAL, EXTERIOR . 23-123,23-130,
23-136
HANDLE - REMOVAL, LATCH RELEASE . . 23-120
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING
..........................8W-01-7
HAZARD SWITCH - DESCRIPTION
.......8L-29
HAZARD SWITCH - INSTALLATION
.......8L-30
HAZARD SWITCH - OPERATION
.........8L-29
HAZARD SWITCH - REMOVAL
..........8L-30
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION
........................5-35
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION
........................5-36
HCU (HYDRAULIC CONTROL UNIT) -
OPERATION
..........................5-35
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL
...........................5-36
HEAD - DESCRIPTION, CYLINDER
........9-30
HEAD COVER(S) - DESCRIPTION,
CYLINDER
...........................9-25
HEAD COVER(S) - INSTALLATION,
CYLINDER
.......................9-26,9-34
HEAD COVER(S) - REMOVAL, CYLINDER
. . 9-25,
9-34
KJINDEX 11
Description Group-Page Description Group-Page Description Group-Page

PRIMARY WEATHERSTRIP - REMOVAL,
DOOR............................23-185
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER........8N-9
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM................8E-1
PROGRAMMING - STANDARD
PROCEDURE, SENTRY KEY
TRANSPONDER.......................8Q-8
PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - FRONT -
INSTALLATION.........................3-6
PROPELLER SHAFT - FRONT - REMOVAL . . . 3-6
PROPELLER SHAFT - REAR -
INSTALLATION.........................3-7
PROPELLER SHAFT - REAR - REMOVAL....3-7
PROPELLER SHAFT ANGLE - STANDARD
PROCEDURES.........................3-3
PROPELLER SHAFT, SPECIFICATIONS.......3-6
PROPORTIONING VALVE - DIAGNOSIS
AND TESTING........................5-20
PULLEY - DESCRIPTION, GENERATOR
DECOUPLER........................8F-26
PULLEY - INSTALLATION..............19-23
PULLEY - INSTALLATION, GENERATOR
DECOUPLER........................8F-30
PULLEY - OPERATION, GENERATOR
DECOUPLER........................8F-27
PULLEY - REMOVAL..................19-23
PULLEY - REMOVAL, GENERATOR
DECOUPLER........................8F-27
PUMP - ASSEMBLY, OIL................9-67
PUMP - ASSEMBLY, OIL..............21-151
PUMP - CLEANING, OIL..............21-150
PUMP - DESCRIPTION................19-17
PUMP - DESCRIPTION, FUEL...........14-15
PUMP - DESCRIPTION, LEAK DETECTION . 25-27
PUMP - DESCRIPTION, OIL............21-147
PUMP - DESCRIPTION, WATER..........7-29
PUMP - DISASSEMBLY, OIL.............9-65
PUMP - DISASSEMBLY, OIL...........21-149
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-18
PUMP - INSPECTION, OIL...............9-66
PUMP - INSPECTION, OIL.............21-150
PUMP - INSTALLATION, LEAK
DETECTION.........................25-28
PUMP - INSTALLATION, OIL.............9-67
PUMP - OPERATION..................19-17
PUMP - OPERATION, FUEL.............14-15
PUMP - OPERATION, LEAK DETECTION . . . 25-28
PUMP - OPERATION, OIL.............21-147
PUMP - OPERATION, WATER............7-30
PUMP - REMOVAL, LEAK DETECTION....25-28
PUMP - REMOVAL, OIL.................9-65
PUMP AMPERAGE TEST - DIAGNOSIS
AND TESTING, FUEL..................14-16
PUMP CAPACITY TEST - DIAGNOSIS
AND TESTING, FUEL..................14-15
PUMP FRONT SEAL - INSTALLATION,
OIL...............................21-152
PUMP FRONT SEAL - REMOVAL, OIL....21-152
PUMP MODULE - DESCRIPTION, FUEL....14-18
PUMP MODULE - INSTALLATION, FUEL . . . 14-19
PUMP MODULE - OPERATION, FUEL.....14-18
PUMP MODULE - REMOVAL, FUEL.......14-18
PUMP PRESSURE TEST - DIAGNOSIS
AND TESTING, FUEL..................14-15
PUMP RELAY - DESCRIPTION, FUEL.....14-34
PUMP RELAY - DIAGNOSIS AND
TESTING, FUEL......................14-34
PUMP RELAY - INSTALLATION, FUEL.....14-34
PUMP RELAY - OPERATION, FUEL.......14-34
PUMP RELAY - REMOVAL, FUEL........14-34
PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD AND FUEL...............8I-4
PUMP, SPECIAL TOOLS - POWER
STEERING..........................19-20
PUMP VOLUME CHECK - STANDARD
PROCEDURE, OIL...................21-148
PUMP/MOTOR - DESCRIPTION, WASHER
. 8R-18
PUMP/MOTOR - INSTALLATION,
WASHER
...........................8R-20
PUMP/MOTOR - OPERATION, WASHER
. . . 8R-19
PUMP/MOTOR - REMOVAL, WASHER
....8R-19
QUARTER TRIM PANEL - INSTALLATION
. 23-159QUARTER TRIM PANEL - REMOVAL.....23-159
QUARTER WINDOW - INSTALLATION....23-172
QUARTER WINDOW - REMOVAL........23-172
QUICK CONNECT FITTING -
DESCRIPTION.......................14-10
QUICK LEARN - STANDARD
PROCEDURE, TCM...................8E-21
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE........................14-10
RACK - INSTALLATION, LUGGAGE......23-144
RACK - REMOVAL, LUGGAGE..........23-144
RADIAL-PLY TIRES - DESCRIPTION.......22-6
RADIATOR - CLEANING.................7-24
RADIATOR - DESCRIPTION..............7-22
RADIATOR - FAN - VISCOUS - CLEANING . . 7-29
RADIATOR - FAN - VISCOUS -
DESCRIPTION........................7-27
RADIATOR - FAN - VISCOUS -
INSPECTION.........................7-29
RADIATOR - FAN - VISCOUS -
INSTALLATION........................7-29
RADIATOR - FAN - VISCOUS -
OPERATION..........................7-27
RADIATOR - FAN - VISCOUS - REMOVAL . . . 7-28
RADIATOR - INSPECTION...............7-24
RADIATOR - INSTALLATION.............7-24
RADIATOR - REMOVAL.................7-23
RADIATOR CROSSMEMBER -
INSTALLATION......................23-146
RADIATOR CROSSMEMBER - REMOVAL . 23-146
RADIATOR FAN - ELECTRIC -
DESCRIPTION........................7-26
RADIATOR FAN - ELECTRIC -
INSTALLATION........................7-27
RADIATOR FAN - ELECTRIC -
OPERATION..........................7-26
RADIATOR FAN - ELECTRIC - REMOVAL . . . 7-26
RADIATOR PRESSURE CAP - CLEANING . . . 7-25
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-25
RADIATOR PRESSURE CAP - DIAGNOSIS
AND TESTING........................7-25
RADIATOR PRESSURE CAP -
INSPECTION.........................7-25
RADIATOR PRESSURE CAP - OPERATION . . 7-25
RADIO - DESCRIPTION.................8A-8
RADIO - INSTALLATION................8A-9
RADIO - OPERATION...................8A-8
RADIO - REMOVAL....................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - DESCRIPTION.................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - INSTALLATION...............8A-11
RADIO NOISE SUPPRESSION GROUND
STRAP - OPERATION.................8A-10
RADIO NOISE SUPPRESSION GROUND
STRAP - REMOVAL...................8A-10
RAIL - DESCRIPTION, FUEL............14-21
RAIL - INSTALLATION, FUEL............14-24
RAIL - OPERATION, FUEL..............14-21
RAIL - REMOVAL, FUEL...............14-22
RAIL WEATHERSTRIP/RETAINER -
INSTALLATION, SIDE.................23-186
RAIL WEATHERSTRIP/RETAINER -
REMOVAL, SIDE....................23-186
RAMP - INSTALLATION, WIPER ARM
PARK..............................8R-43
RAMP - REMOVAL, WIPER ARM PARK . . . 8R-43
RANGE INDICATOR ILLUMINATION BULB
- INSTALLATION, TRANSMISSION........8L-83
RANGE INDICATOR ILLUMINATION BULB
- REMOVAL, TRANSMISSION
...........8L-82
RANGE SENSOR - DESCRIPTION,
TRANSMISSION
.....................21-168
RANGE SENSOR - OPERATION,
TRANSMISSION
.....................21-168
RATINGS, GAS ENGINES - GENERATOR
. . . 8F-23
RBI AXLE - INSTALLATION, 198
..........5-28
RBI AXLE - REMOVAL, 198
..............5-27
READING LAMP BULB - INSTALLATION
. . . 8L-79
READING LAMP BULB - REMOVAL
.......8L-79
READING LAMP SWITCH -
INSTALLATION
.......................8L-80
READING LAMP SWITCH - REMOVAL
.....8L-80
READING LAMP UNIT - INSTALLATION
. . . 8L-81
READING LAMP UNIT - REMOVAL
.......8L-81
REAR - DESCRIPTION
..................2-16REAR - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-48
REAR - INSTALLATION, PROPELLER
SHAFT...............................3-7
REAR - INSTALLATION, SEAT..........23-168
REAR - INSTALLATION, SEAT BACK.....23-168
REAR - INSTALLATION, SEAT BACK
COVER............................23-169
REAR - INSTALLATION, SEAT BACK
CUSHION..........................23-170
REAR - INSTALLATION, SEAT BACK
FRAME............................23-171
REAR - INSTALLATION, SEAT CUSHION . . 23-171
REAR - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-48
REAR AXLE - 198RBI - DESCRIPTION.....3-49
REAR AXLE - 198RBI - INSTALLATION.....3-54
REAR AXLE - 198RBI - OPERATION.......3-49
REAR AXLE - 198RBI - REMOVAL........3-54
REAR AXLE - 8 1/4 - ADJUSTMENTS......3-92
REAR AXLE - 8 1/4 - DESCRIPTION.......3-86
REAR AXLE - 8 1/4 - INSTALLATION......3-91
REAR AXLE - 8 1/4 - OPERATION.........3-86
REAR AXLE - 8 1/4 - REMOVAL..........3-91
REAR AXLE - SPECIFICATIONS...........3-62
REAR AXLE, SPECIAL TOOLS............3-63
REAR AXLE, SPECIFICATIONS............3-98
REAR BRAKE HOSE - INSTALLATION......5-10
REAR BRAKE HOSE - REMOVAL...........5-9
REAR CENTER SEAT BELT &
RETRACTOR - INSTALLATION...........8O-33
REAR CENTER SEAT BELT &
RETRACTOR - REMOVAL..............8O-32
REAR CHECK VALVE - DESCRIPTION.....8R-34
REAR CHECK VALVE - INSTALLATION....8R-35
REAR CHECK VALVE - OPERATION.......8R-34
REAR CHECK VALVE - REMOVAL........8R-34
REAR CROSSMEMBER - INSTALLATION....13-7
REAR CROSSMEMBER - REMOVAL.......13-7
REAR DOOR OUTER BELT MOLDING -
INSTALLATION......................23-186
REAR DOOR OUTER BELT MOLDING -
REMOVAL.........................23-186
REAR DOOR SCUFF PLATE -
INSTALLATION......................23-160
REAR DOOR SCUFF PLATE - REMOVAL . . 23-160
REAR DRUM BRAKE - ADJUSTMENT......5-12
REAR DRUM BRAKE - DESCRIPTION......5-10
REAR DRUM BRAKE - OPERATION........5-11
REAR FASCIA - INSTALLATION...........13-2
REAR FASCIA - REMOVAL...............13-2
REAR FASCIA SUPPORT - INSTALLATION . . 13-3
REAR FASCIA SUPPORT - REMOVAL......13-3
REAR FOG LAMP INDICATOR -
DESCRIPTION.......................8J-27
REAR FOG LAMP INDICATOR -
OPERATION.........................8J-27
REAR FOG LAMP RELAY - DESCRIPTION . . 8L-56
REAR FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-57
REAR FOG LAMP RELAY -
INSTALLATION.......................8L-58
REAR FOG LAMP RELAY - OPERATION . . . 8L-57
REAR FOG LAMP RELAY - REMOVAL.....8L-58
REAR GLASS HEATING GRID REPAIR -
STANDARD PROCEDURE...............8G-4
REAR HVAC CONTROL ASSEMBLY
WINDOW DEFOGGER FUNCTION -
DIAGNOSIS AND TESTING..............8G-9
REAR LAMP BULB - INSTALLATION......8L-59
REAR LAMP BULB - REMOVAL..........8L-58
REAR LAMP UNIT - INSTALLATION......8L-60
REAR LAMP UNIT - REMOVAL..........8L-59
REAR MOUNT - INSTALLATION..........9-57
REAR MOUNT - REMOVAL..............9-57
REAR OUTBOARD SEAT BELT &
RETRACTOR - INSTALLATION...........8O-34
REAR OUTBOARD SEAT BELT &
RETRACTOR - REMOVAL..............8O-33
REAR OUTPUT SHAFT SEAL -
INSTALLATION
......................21-212
REAR OUTPUT SHAFT SEAL - REMOVAL
. 21-210
REAR SEAL AREA LEAKS - DIAGNOSIS
AND TESTING
........................9-61
REAR SEAT BACK LATCH / LOCK -
INSTALLATION, FOLDING
.............23-170
REAR SEAT BACK LATCH / LOCK -
REMOVAL, FOLDING
.................23-170
20 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

RELAY - OPERATION, FRONT FOG LAMP . . 8L-22
RELAY - OPERATION, FUEL PUMP.......14-34
RELAY - OPERATION, HEADLAMP HIGH
BEAM..............................8L-33
RELAY - OPERATION, HEADLAMP LOW
BEAM..............................8L-39
RELAY - OPERATION, PARK LAMP.......8L-54
RELAY - OPERATION, REAR FOG LAMP . . . 8L-57
RELAY - OPERATION, REAR WINDOW
DEFOGGER..........................8G-6
RELAY - OPERATION, STARTER MOTOR . . . 8F-42
RELAY - OPERATION, TRAILER TOW.....8L-62
RELAY - OPERATION, TRANSMISSION
CONTROL.........................21-168
RELAY - OPERATION, WIPER HIGH/LOW . . 8R-23
RELAY - OPERATION, WIPER ON/OFF....8R-25
RELAY - REMOVAL................8W-97-14
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-16
RELAY - REMOVAL, AMPLIFIER CHOKE....8A-4
RELAY - REMOVAL, BLOWER MOTOR....24-21
RELAY - REMOVAL, CLUTCH SWITCH
OVERRIDE...........................6-10
RELAY - REMOVAL, DAYTIME RUNNING
LAMP..............................8L-21
RELAY - REMOVAL, DOOR LOCK.........8N-6
RELAY - REMOVAL, FRONT FOG LAMP . . . 8L-24
RELAY - REMOVAL, FUEL PUMP........14-34
RELAY - REMOVAL, HEADLAMP HIGH
BEAM..............................8L-34
RELAY - REMOVAL, HEADLAMP LOW
BEAM..............................8L-40
RELAY - REMOVAL, HORN..............8H-3
RELAY - REMOVAL, PARK LAMP........8L-55
RELAY - REMOVAL, REAR FOG LAMP....8L-58
RELAY - REMOVAL, REAR WINDOW
DEFOGGER..........................8G-7
RELAY - REMOVAL, STARTER MOTOR....8F-43
RELAY - REMOVAL, TRAILER TOW.......8L-63
RELAY - REMOVAL, WIPER HIGH/LOW . . . 8R-24
RELAY - REMOVAL, WIPER ON/OFF......8R-26
RELAYS - DIAGNOSIS AND TESTING,
ASD AND FUEL PUMP..................8I-4
RELEASE - STANDARD PROCEDURE,
FUEL SYSTEM PRESSURE..............14-4
RELEASE BEARING - INSTALLATION,
CLUTCH..............................6-6
RELEASE BEARING - REMOVAL, CLUTCH . . . 6-6
RELEASE CABLE - INSTALLATION, LATCH . 23-120
RELEASE CABLE - REMOVAL, LATCH....23-120
RELEASE HANDLE - INSTALLATION,
LATCH ............................23-120
RELEASE HANDLE - REMOVAL, LATCH . . 23-120
RELEASE SWITCH - DIAGNOSIS AND
TESTING, FLIP-UP GLASS..............8N-5
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE.........................24-42
RELIEF VALVE - OPERATION, HIGH
PRESSURE.........................24-42
REMOTE KEYLESS ENTRY MODULE -
DESCRIPTION........................8N-7
REMOTE KEYLESS ENTRY MODULE -
DIAGNOSIS AND TESTING..............8N-7
REMOTE KEYLESS ENTRY MODULE -
INSTALLATION.......................8N-7
REMOTE KEYLESS ENTRY MODULE -
OPERATION..........................8N-7
REMOTE KEYLESS ENTRY MODULE -
REMOVAL...........................8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - DIAGNOSIS AND
TESTING............................8N-8
REMOTE KEYLESS ENTRY
TRANSMITTER - SPECIFICATIONS........8N-9
REMOTE SWITCHES - DESCRIPTION.....8A-11
REMOTE SWITCHES - DIAGNOSIS AND
TESTING...........................8A-12
REMOTE SWITCHES - INSTALLATION.....8A-13
REMOTE SWITCHES - OPERATION.......8A-12
REMOTE SWITCHES - REMOVAL
........8A-13
REPAIR - DESCRIPTION, THREADED
HOLE
.............................Intro.-4
REPAIR - STANDARD PROCEDURE,
ALUMINUM THREAD
..................21-81
REPAIR - STANDARD PROCEDURE,
REAR GLASS HEATING GRID
............8G-4
REPAIR DAMAGED OR WORN THREADS
- STANDARD PROCEDURE
...............9-9REPAIRING LEAKS - STANDARD
PROCEDURE.........................22-8
REPEATER LAMP BULB - INSTALLATION . . 8L-60
REPEATER LAMP BULB - REMOVAL......8L-60
REPEATER LAMP UNIT - INSTALLATION . . 8L-61
REPEATER LAMP UNIT - REMOVAL......8L-60
REQUIREMENTS - DESCRIPTION,
COOLING SYSTEM....................24-1
RESERVOIR - DESCRIPTION, VACUUM....8P-7
RESERVOIR - DESCRIPTION, WASHER . . . 8R-21
RESERVOIR - DIAGNOSIS AND TESTING,
VACUUM............................8P-7
RESERVOIR - INSTALLATION, FLUID......5-26
RESERVOIR - INSTALLATION, VACUUM....8P-8
RESERVOIR - INSTALLATION, WASHER . . . 8R-22
RESERVOIR - OPERATION, VACUUM......8P-7
RESERVOIR - OPERATION, WASHER.....8R-21
RESERVOIR - REMOVAL, FLUID..........5-26
RESERVOIR - REMOVAL, VACUUM........8P-7
RESERVOIR - REMOVAL, WASHER......8R-21
RESISTANCE, 2.4L - IGNITION COIL.......8I-2
RESISTANCE, 2.4L - SPARK PLUG CABLE . . . 8I-3
RESISTANCE, 3.7L V-6 - IGNITION COIL....8I-3
RESISTOR - DESCRIPTION, BLOWER
MOTOR............................24-22
RESISTOR - DIAGNOSIS AND TESTING,
BLOWER MOTOR....................24-22
RESISTOR - INSTALLATION, BLOWER
MOTOR............................24-22
RESISTOR - OPERATION, BLOWER
MOTOR............................24-22
RESISTOR - REMOVAL, BLOWER
MOTOR............................24-22
RESTRAINT DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL......................8O-6
RESTRAINT SYSTEM - DIAGNOSIS AND
TESTING, SUPPLEMENTAL..............8O-6
RESTRAINT SYSTEM - WARNING........8O-5
RESTRAINTS - DESCRIPTION............8O-2
RESTRAINTS - OPERATION.............8O-4
RESTRAINTS - STANDARD PROCEDURE,
HANDLING NON-DEPLOYED
SUPPLEMENTAL......................8O-6
RETAINER/BULKHEAD - ASSEMBLY, 4C . . 21-123
RETAINER/BULKHEAD - DISASSEMBLY,
4C ...............................21-122
RETRACTOR - INSTALLATION, FRONT
SEAT BELT .........................8O-24
RETRACTOR - INSTALLATION, REAR
CENTER SEAT BELT..................8O-33
RETRACTOR - INSTALLATION, REAR
OUTBOARD SEAT BELT................8O-34
RETRACTOR - REMOVAL, FRONT SEAT
BELT ..............................8O-23
RETRACTOR - REMOVAL, REAR CENTER
SEAT BELT .........................8O-32
RETRACTOR - REMOVAL, REAR
OUTBOARD SEAT BELT................8O-33
RETURN - DESCRIPTION, SENSOR.......8E-14
RETURN HOSE (GEAR TO THE COOLER)
- INSTALLATION.....................19-22
RETURN HOSE (GEAR TO THE COOLER)
- REMOVAL.........................19-21
RETURN HOSE (RESERVOIR TO THE
COOLER) - INSTALLATION.............19-22
RETURN HOSE (RESERVOIR TO THE
COOLER) - REMOVAL
.................19-21
REVERSE FLUSHING - STANDARD
PROCEDURE, COOLING SYSTEM
.........7-12
RFE TRANSMISSION, SPECIAL TOOLS
. . . 21-120
RHD - INSTALLATION
...............8W-97-6
RHD - REMOVAL
...................8W-97-5
RIGHT POWER SEAT SWITCH -
DESCRIPTION
.......................8N-19
RIGHT POWER SEAT SWITCH -
DIAGNOSIS AND TESTING
.............8N-19
RIGHT POWER SEAT SWITCH -
INSTALLATION
......................8N-20
RIGHT POWER SEAT SWITCH -
OPERATION
.........................8N-19
RIGHT POWER SEAT SWITCH -
REMOVAL
..........................8N-20
RIGHT SIDE - INSTALLATION
........2-12,2-15
RIGHT SIDE - REMOVAL
............2-11,2-14
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE
...........3-112,3-82RING - REMOVAL, PINION GEAR/RING
GEAR/TONE.....................3-110,3-79
RING FITTING - STANDARD
PROCEDURE, PISTON..................9-52
RISER - INSTALLATION, MANUAL SEAT . . 23-168
RISER - REMOVAL, MANUAL SEAT......23-167
RKE TRANSMITTER BATTERIES -
STANDARD PROCEDURE...............8N-8
RKE TRANSMITTER CUSTOMER
PREFERENCES - STANDARD
PROCEDURE.........................8N-8
RKE TRANSMITTER PROGRAMING -
STANDARD PROCEDURE...............8N-9
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-2
ROAD TESTING - DIAGNOSIS AND
TESTING...........................21-78
ROCKER ARM - DESCRIPTION.......9-29,9-37
ROCKER ARM - INSTALLATION..........9-37
ROCKER ARM - REMOVAL..............9-37
ROD - DESCRIPTION, PISTON &
CONNECTING.........................9-49
ROD BEARING - FITTING - STANDARD
PROCEDURE, CONNECTING.............9-40
ROD BEARING, FITTING - CONNECTING....9-49
ROD END - INSTALLATION, TIE.........19-16
ROD END - REMOVAL, TIE.............19-16
ROD END REMOVAL TOOL, SPECIAL
TOOLS - OUTER TIE..................19-15
ROTATION - STANDARD PROCEDURE,
TIRE................................22-2
ROTOR - DIAGNOSIS AND TESTING,
DISC BRAKE.........................5-18
ROTOR - STANDARD PROCEDURE, DISC
BRAKE..............................5-19
ROTORS - INSTALLATION...............5-19
ROTORS - REMOVAL..................5-19
ROUTING 3.7L ENGINE - DESCRIPTION,
COOLING SYSTEM.....................7-2
RUN CHANNEL - INSTALLATION, GLASS . 23-123,
23-130
RUN CHANNEL - REMOVAL, GLASS....23-123,
23-130
RUNNING LAMP RELAY - DESCRIPTION,
DAYTIME...........................8L-20
RUNNING LAMP RELAY - INSTALLATION,
DAYTIME...........................8L-21
RUNNING LAMP RELAY - OPERATION,
DAYTIME...........................8L-20
RUNNING LAMP RELAY - REMOVAL,
DAYTIME...........................8L-21
RUNOUT - DIAGNOSIS AND TESTING,
TIRES AND WHEEL....................22-1
SAFETY CERTIFICATION LABEL -
DESCRIPTION, VEHICLE..............Intro.-9
SAFETY PRECAUTIONS AND WARNINGS,
WARNING...........................23-1
SAFETY PRECAUTIONS, WARNING -
WINDSHIELD.......................23-173
SANDING/BUFFING & POLISHING -
DESCRIPTION, FINESSE..............23-163
SCHEDULES - DESCRIPTION,
MAINTENANCE........................0-4
SCHEMATICS AND DIAGRAMS -
HYDRAULIC SCHEMATICS.............21-100
SCHEMATICS, SCHEMATICS AND
DIAGRAMS - HYDRAULIC.............21-100
SCUFF PLATE - INSTALLATION, DOOR
SILL..............................23-157
SCUFF PLATE - INSTALLATION, REAR
DOOR............................23-160
SCUFF PLATE - REMOVAL, DOOR SILL . . . 23-157
SCUFF PLATE - REMOVAL, REAR DOOR . . 23-160
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL.....................9-47
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL.....................9-46
SEAL - INSTALLATION, ADAPTER
HOUSING..........................21-124
SEAL - INSTALLATION, A-PILLAR.......23-185
SEAL - INSTALLATION, COWL/PLENUM . . 23-187
SEAL - INSTALLATION, COWL/PLENUM
WINDOW BAFFLE
...................23-187
SEAL - INSTALLATION, FRONT OUTPUT
SHAFT
......................21-208,21-246
SEAL - INSTALLATION, GLASS PANEL
. . . 23-178
SEAL - INSTALLATION, OIL PUMP
FRONT
............................21-152
SEAL - INSTALLATION, PINION
. . 3-103,3-39,3-68
22 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page