2002 JEEP LIBERTY motor fan

(8) Install the starter.
(9) Connect the crankshaft position sensor.
(10) Install the engine block heater power cable, if
equipped.
CAUTION: The structural cover requires a specific
torque sequence. Failure to follow this sequence
may cause severe damage to the cover.
(11) Install the structural cover.
(12) Install the exhaust pipe.
(13) Connect the oxygen sensors.
(14) Lower vehicle.
(15) Connect the knock sensors.
(16) Connect the engine to body ground straps.
(17) Install the power brake booster vacuum hose.
(18) Install the breather hoses.
(19) Install the PCV hose.
(20) Install the fuel rail.
(21) Install the coil over plugs.
(22) Reconnect the engine wiring harness at the
following points:
²Intake air temperature (IAT) sensor
²Fuel Injectors
²Throttle Position (TPS) Switch
²Idle Air Control (IAC) Motor
²Engine Oil Pressure Switch
²Engine Coolant Temperature (ECT) Sensor
²Manifold Absolute Pressure MAP) Sensor
²Camshaft Position (CMP) Sensor
²Coil Over Plugs
²Crankshaft Position Sensor
(23) Connect lower radiator hose.
(24) Connect upper radiator hose.
(25) Connect throttle and speed control cables.
(26) Install the heater hose assembly.
(27) Install coolant recovery bottle.
(28) Install the power steering pump.
(29) Install the generator.
(30) Install the A/C compressor.
(31) Install the drive belt.
(32) Install the fan shroud with the electric fan
assembly.
(33) Install the radiator core support bracket.
(34) Install the air cleaner assembly.
(35) Refill the engine cooling system.
(36) Install the hood.
(37) Check and fill engine oil.
(38) Connect the battery negative cable.
(39) Start the engine and check for leaks.SPECIFICATIONS
SPECIFICATIONS - 2.4L ENGINE
DESCRIPTION SPECIFICATION
General Specification
Type In-Line OHV, DOHC
Number of Cylinders 4
Displacement 2.4 Liters
(148 cu. in.)
Bore 87.5 mm
(3.445 in.)
Stroke 101.0 mm
(3.976 in.)
Compression Ratio 9.4:1
Firing Order 1-3-4-2
Compression Pressure 690 kPa (Minimum)
(100 psi Minimum)
Max. Variation Between
Cylinders25%
Cylinder Block
Cylinder Bore Diameter 87.4924±87.5076 mm
(3.4446±3.4452 in.)
Out-of-Round (Max.) 0.051 mm
(0.002 in.)
Taper (Max.) 0.051 mm
(0.002 in.)
Pistons
Piston Diameter 87.463±87.481 mm
(3.4434±3.4441 in.)
Clearance @ 14 mm
(9/16 in.) from bottom of
skirt0.024±0.057 mm
(0.0009±0.0022 in.)
Weight 346±356 grams
(12.20±12.56 oz.)
Land Clearance
(Diametrical)0.614±0.664 mm
(0.024±0.026 in.)
Piston Length 66.25 mm
(2.608 in.)
Piston Ring Groove
Depth No. 14.640±4.784 mm
(0.182±0.188 in.)
Piston Ring Groove
Depth No. 24.575±4.719 mm
(0.180±0.185 in.)
KJENGINE9s-13
ENGINE - 2.4L (Continued)

(6) Install the serpentine belt (Refer to 7 - COOL-
ING/ACCESSORY DRIVE/DRIVE BELTS - INSTAL-
LATION).
(7) Install the fan shroud.
(8) Install the fan (Refer to 7 - COOLING/EN-
GINE/RADIATOR FAN - INSTALLATION).
(9) Install the radiator crossmember (Refer to 23 -
BODY/EXTERIOR/RADIATOR CROSSMEMBER -
INSTALLATION).
(10) Refill the power steering fluid (Refer to 19 -
STEERING/PUMP - STANDARD PROCEDURE).
INSTALLATION - RETURN HOSE (GEAR TO THE
COOLER)
(1) Install the return hose to the vehicle. (Fig. 7)
(2) Install the return hose mounting bracket bolts
to the front cradle.
(3) Install the return hose at the cooler.
(4) Install the return hose at the gear 28 N´m (21
ft.lbs.).
(5) Install the serpentine belt (Refer to 7 - COOL-
ING/ACCESSORY DRIVE/DRIVE BELTS - INSTAL-
LATION).
(6) Install the fan shroud.
(7) Install the fan (Refer to 7 - COOLING/EN-
GINE/RADIATOR FAN - INSTALLATION).
(8) Install the radiator crossmember (Refer to 23 -
BODY/EXTERIOR/RADIATOR CROSSMEMBER -
INSTALLATION).
(9) Refill the power steering fluid (Refer to 19 -
STEERING/PUMP - STANDARD PROCEDURE).
INSTALLATION - RETURN HOSE (RESERVOIR
TO THE COOLER)
(1) Install the return hose to the vehicle.
(2) Install the return hose to the pump reservoir.
(3) Install the return hose at the cooler.
(4) Refill the power steering fluid (Refer to 19 -
STEERING/PUMP - STANDARD PROCEDURE).
POWER STEERING PRESSURE
SWITCH
DESCRIPTION
A pressure sensing switch is used in the power
steering system. It is mounted on the high-pressure
steering hose. This switch will be used with both
2.4L and 3.7L engines.
OPERATION
The switch is used on both the 2.4L 4±cylinder and
3.7L V-6 engines.
The power steering pressure switch provides an
input to the Powertrain Control Module (PCM). This
input is provided during periods of high steering
pump load and low engine rpm; such as during park-
ing maneuvers. The PCM increases the idle speed
through the Idle Air Control (IAC) motor. This is
done to prevent the engine from stalling under the
increased load.
When steering pump pressure exceeds 3275 kPa  
690 kPa (475 psi   100 psi), the Normally Closed
(NC) switch will open and the PCM will increase the
engine idle speed. This will prevent the engine from
stalling.
When pump pressure drops to approximately 1379
kPa (200 psi), the switch circuit will re-close and
engine idle speed will return to its previous setting.
REMOVAL
The power steering pressure switch is installed in
the power steering high-pressure hose (Fig. 9).
(1) Remove the high pressure power steering
hose(Refer to 19 - STEERING/PUMP/HOSES -
REMOVAL).
(2) Disconnect electrical connector from power
steering pressure switch.
(3) Place a small container or shop towel beneath
switch to collect any excess fluid.
(4) Remove switch. Use back-up wrench on power
steering line to prevent line bending.
INSTALLATION
(1) Install power steering switch into power steer-
ing line. (Fig. 9)
(2) Tighten to 9.6 N´m (85 in. lbs.) torque.
Fig. 8 HIGH PRESSURE HOSE ASSEMBLY
1 - HIGH PRESSURE POWER STEERING HOSE
2 - MOUNTING BRACKET
3 - POWER STEERING PRESURE SWITCH
19 - 22 PUMPKJ
HOSES (Continued)

DIAGNOSIS AND TESTING - HEATER
PERFORMANCE
Before performing the following tests, refer to Cool-
ing for the procedures to check the radiator coolant
level, serpentine drive belt tension, radiator air flow
and the radiator fan operation. Also be certain that
the accessory vacuum supply line is connected at the
engine intake manifold.
MAXIMUM HEATER OUTPUT
Engine coolant is delivered to the heater core
through two heater hoses. With the engine idling atnormal operating temperature, set the temperature
control knob in the full hot position, the mode control
switch knob in the floor heat position, and the blower
motor switch knob in the highest speed position.
Using a test thermometer, check the temperature of
the air being discharged at the HVAC housing floor
outlets. Compare the test thermometer reading to the
Temperature Reference chart.
Temperature Reference
Ambient Air Temperature15.5É C
(60É F)21.1É C
(70É F)26.6É C
(80É F)32.2É C
(90É F)
Minimum Air Temperature at
Floor Outlet52.2É C
(126É F)56.1É C
(133É F)59.4É C
(139É F)62.2É C
(144É F)
If the floor outlet air temperature is too low, refer
to Cooling to check the engine coolant temperature
specifications. Both of the heater hoses should be hot
to the touch. The coolant return heater hose should
be slightly cooler than the coolant supply heater
hose. If the return hose is much cooler than the sup-
ply hose, locate and repair the engine coolant flow
obstruction in the cooling system. Refer to Cooling
for the procedures.
OBSTRUCTED COOLANT FLOW Possible loca-
tions or causes of obstructed coolant flow:
²Pinched or kinked heater hoses.
²Improper heater hose routing.
²Plugged heater hoses or supply and return ports
at the cooling system connections.
²A plugged heater core.
If proper coolant flow through the cooling system is
verified, and heater outlet air temperature is still
low, a mechanical problem may exist.
MECHANICAL PROBLEMS Possible locations or
causes of insufficient heat:
²An obstructed cowl air intake.
²Obstructed heater system outlets.
²A blend door not functioning properly.
TEMPERATURE CONTROL
If the heater outlet air temperature cannot be
adjusted with the temperature control knob on theA/C Heater control panel, the following could require
service:
²The A/C Heater control.
²The blend door actuator.
²The blend door.
²Improper engine coolant temperature.
DIAGNOSIS AND TESTING - VACUUM SYSTEM
Vacuum control is used to operate the mode doors
in the heater-only and a/c heater housings. Testing of
the heater-only and A/C Heater mode control switch
operation will determine if the vacuum, electrical,
and mechanical controls are functioning. However, it
is possible that a vacuum control system that oper-
ates perfectly at engine idle (high engine vacuum)
may not function properly at high engine speeds or
loads (low engine vacuum). This can be caused by
leaks in the vacuum system, or a faulty vacuum
check valve.
A vacuum system test will help to identify the
source of poor vacuum system performance or vac-
uum system leaks. Before starting this test, stop the
engine and make certain that the problem is not a
disconnected vacuum supply tube at the engine
intake manifold vacuum tap or at the vacuum reser-
voir.
24 - 6 HEATING & AIR CONDITIONINGKJ
HEATING & AIR CONDITIONING (Continued)

(5) Connect the test set hose or probe to the open
end of the leaking circuit. The test set gauge should
return to the 27 kPa (8 in. Hg.) setting shortly after
each connection is made. If OK, replace the faulty
disconnected component. If not OK, go to Step 6.
(6)
To locate a leak in a vacuum line, leave one end
of the line plugged and connect the test set hose or
probe to the other end of the line. Run your fingers
slowly along the line while watching the test set gauge.
The vacuum reading will fluctuate when your fingers
contact the source of the leak. To repair the vacuum
line, cut out the leaking section of the line. Then, insert
the loose ends of the line into a suitable length of 3 mil-
limeter (0.125 inch) inside diameter rubber hose.
STANDARD PROCEDURE - DIODE
REPLACEMENT
(1) Disconnect the battery negative cable and iso-
late it.
(2) Locate the diode in the harness, and remove
the protective covering.
(3) Remove the diode from the harness, pay atten-
tion to the current flow direction (Fig. 5).
(4) Remove the insulation from the wires in the
harness. Only remove enough insulation to solder in
the new diode.
(5) Install the new diode in the harness, making
sure current flow is correct. If necessary refer to the
appropriate wiring diagram for current flow.
(6) Solder the connection together using rosin core
type solder only.Do not use acid core solder.
(7) Tape the diode to the harness using electrical
tape making, sure the diode is completely sealed
from the elements.
(8) Re-connect the battery negative cable, and test
affected systems.
SPECIFICATIONS
A/C APPLICATION TABLE
Item Description Notes
Vehicle KJ- Liberty
System R134a w/ fixed
orifice tube
Compressor Sanden PXF-18 SP-10 PAG oil
Freeze±up
ControlA/C low
pressure switchaccumulator
mounted
Low psi Control opens < 25 psi
- resets > 43
psi
High psi Control switch - opens
> 450-490 psi -
resets <
270-330 psidischarge line
Control Head manual type
Mode Door vacuum
Blend Door electric
Recirculation
Doorvacuum
Blower Motor hardwired to
control headresistor block
Cooling Fan viscous for
cooling, single
speed electric
for A/C
Clutch Electro-
mechanical
Control relay PCM
Draw 2 - 3.7 amps @
12V  0.5V @ 70É F
Gap 0.0169- 0.0319
DRB IIIT
Reads TPS, RPM, A/C
switch test
Actuators clutch and fan
relay
Fig. 5 DIODE IDENTIFICATION
1 - CURRENT FLOW
2 - BAND AROUND DIODE INDICATES CURRENT FLOW
3 - DIODE AS SHOWN IN THE DIAGRAMS
KJHEATING & AIR CONDITIONING 24 - 9
HEATING & AIR CONDITIONING (Continued)

DIFFERENTIAL - TRAC-LOK - CLEANING . . 3-109,
3-77
DIFFERENTIAL - TRAC-LOK -
DISASSEMBLY...................3-107,3-75
DIFFERENTIAL - TRAC-LOK -
INSPECTION....................3-109,3-77
DIFFERENTIAL CASE BEARINGS -
INSTALLATION...............3-110,3-44,3-79
DIFFERENTIAL CASE BEARINGS -
REMOVAL..................3-110,3-43,3-79
DIMENSIONS - SPECIFICATIONS, FRAME . . . 13-3
DIMENSIONS - SPECIFICATIONS,
OPENING..........................23-111
DIODE - INSTALLATION............8W-01-14
DIODE - REMOVAL................8W-01-14
DIODE REPLACEMENT - STANDARD
PROCEDURE.........................24-9
DISASSEMBLY - POWER DISTRIBUTION
CENTER DISASSEMBLY.............8W-97-7
DISASSEMBLY, 4C RETAINER/BULKHEAD . 21-122
DISASSEMBLY, DIAGNOSIS AND
TESTING...........................21-83
DISASSEMBLY, DIFFERENTIAL......3-105,3-41
DISASSEMBLY, DIFFERENTIAL -
TRAC-LOK......................3-107,3-75
DISASSEMBLY, DISASSEMBLY - POWER
DISTRIBUTION CENTER.............8W-97-7
DISASSEMBLY, DISC BRAKE CALIPERS....5-14
DISASSEMBLY, HVAC HOUSING.........24-34
DISASSEMBLY, INPUT CLUTCH
ASSEMBLY.........................21-135
DISASSEMBLY, INSTRUMENT CLUSTER....8J-9
DISASSEMBLY, LOW/REVERSE CLUTCH . . 21-145
DISASSEMBLY, MANUAL - NV1500........21-4
DISASSEMBLY, MANUAL - NV3550.......21-35
DISASSEMBLY, OIL PUMP...............9-65
DISASSEMBLY, OIL PUMP.............21-149
DISASSEMBLY, PLANETARY GEARTRAIN . 21-159
DISASSEMBLY, SINGLE CARDAN
UNIVERSAL JOINTS....................3-8
DISASSEMBLY, TRANSFER CASE -
NV231............................21-182
DISASSEMBLY, TRANSFER CASE -
NV242............................21-218
DISASSEMBLY, VALVE BODY...........21-173
DISASSEMBLY, WHEEL CYLINDERS.......5-28
DISC - INSTALLATION, CLUTCH...........6-6
DISC - REMOVAL, CLUTCH...............6-6
DISC BRAKE CALIPER ADAPTER -
INSTALLATION........................5-18
DISC BRAKE CALIPER ADAPTER -
REMOVAL...........................5-18
DISC BRAKE CALIPERS - ASSEMBLY......5-16
DISC BRAKE CALIPERS - CLEANING......5-16
DISC BRAKE CALIPERS - DESCRIPTION....5-13
DISC BRAKE CALIPERS - DISASSEMBLY . . . 5-14
DISC BRAKE CALIPERS - INSPECTION.....5-16
DISC BRAKE CALIPERS - INSTALLATION . . . 5-17
DISC BRAKE CALIPERS - OPERATION.....5-14
DISC BRAKE CALIPERS - REMOVAL.......5-14
DISC BRAKE ROTOR - DIAGNOSIS AND
TESTING............................5-18
DISC BRAKE ROTOR - STANDARD
PROCEDURE.........................5-19
DISCHARGE (ESD) SENSITIVE DEVICES -
STANDARD PROCEDURE,
ELECTROSTATIC...................8W-01-8
DISCHARGE LINE - INSTALLATION, A/C . . . 24-47
DISCHARGE LINE - REMOVAL, A/C.......24-46
DISPLAY TEST MODE - DESCRIPTION,
STATE ..............................25-2
DISTRIBUTION - DESCRIPTION, POWER . 8W-97-1
DISTRIBUTION - OPERATION, POWER . . 8W-97-1
DISTRIBUTION CENTER - DESCRIPTION,
POWER..........................8W-97-6
DISTRIBUTION CENTER - OPERATION,
POWER..........................8W-97-7
DISTRIBUTION CENTER - REMOVAL,
POWER..........................8W-97-7
DISTRIBUTION CENTER ASSEMBLY,
ASSEMBLY - POWER
..............8W-97-10
DISTRIBUTION CENTER DISASSEMBLY,
DISASSEMBLY - POWER
............8W-97-7
DISTRIBUTION SYSTEMS, SPECIAL
TOOLS - POWER
...................8W-97-2
DOO - INSTALLATION, FLOOR -
DEFROST
...........................24-37
DOOR - INSTALLATION
.........23-122,23-129DOOR - INSTALLATION, BLEND.........24-35
DOOR - INSTALLATION, PANEL..........24-36
DOOR - INSTALLATION, PASSENGER
AIRBAG............................8O-30
DOOR - INSTALLATION, RECIRC.........24-37
DOOR - REMOVAL.............23-122,23-129
DOOR - REMOVAL, BLEND.............24-35
DOOR - REMOVAL, DEFROST...........24-35
DOOR - REMOVAL, FLOOR - DEFROST....24-36
DOOR - REMOVAL, PASSENGER AIRBAG . . 8O-29
DOOR - REMOVAL, RECIRC............24-37
DOOR ACTUATOR - INSTALLATION,
BLEND.............................24-20
DOOR ACTUATOR - INSTALLATION,
FLOOR - DEFROST...................24-25
DOOR ACTUATOR - INSTALLATION,
PANEL.............................24-25
DOOR ACTUATOR - INSTALLATION,
RECIRCULATION.....................24-26
DOOR ACTUATOR - REMOVAL, BLEND....24-20
DOOR ACTUATOR - REMOVAL, FLOOR -
DEFROST...........................24-24
DOOR ACTUATOR - REMOVAL, PANEL....24-24
DOOR ACTUATOR - REMOVAL,
RECIRCULATION.....................24-26
DOOR AJAR INDICATOR - DESCRIPTION . . 8J-17
DOOR AJAR INDICATOR - OPERATION....8J-17
DOOR AJAR SWITCH - DESCRIPTION....8L-77
DOOR AJAR SWITCH - OPERATION........8L-77
DOOR CYLINDER LOCK SWITCH -
DESCRIPTION........................8Q-9
DOOR CYLINDER LOCK SWITCH -
DIAGNOSIS AND TESTING.............8Q-10
DOOR CYLINDER LOCK SWITCH -
INSTALLATION......................8Q-10
DOOR CYLINDER LOCK SWITCH -
OPERATION.........................8Q-10
DOOR CYLINDER LOCK SWITCH -
REMOVAL..........................8Q-10
DOOR GLASS - INSTALLATION . . 23-122,23-129,
23-172
DOOR GLASS - REMOVAL......23-122,23-129,
23-172
DOOR LOCK / UNLOCK SWITCH -
INSTALLATION.......................8N-5
DOOR LOCK / UNLOCK SWITCH -
REMOVAL...........................8N-4
DOOR LOCK MOTOR - DESCRIPTION......8N-5
DOOR LOCK MOTOR - DIAGNOSIS AND
TESTING............................8N-5
DOOR LOCK MOTOR - OPERATION.......8N-5
DOOR LOCK RELAY - DESCRIPTION......8N-6
DOOR LOCK RELAY - DIAGNOSIS AND
TESTING............................8N-6
DOOR LOCK RELAY - INSTALLATION......8N-7
DOOR LOCK RELAY - OPERATION........8N-6
DOOR LOCK RELAY - REMOVAL.........8N-6
DOOR LOCK/UNLOCK SWITCH -
DIAGNOSIS AND TESTING..............8N-4
DOOR LOWER WEATHERSTRIP -
INSTALLATION......................23-186
DOOR LOWER WEATHERSTRIP -
REMOVAL.........................23-186
DOOR OUTER BELT MOLDING -
INSTALLATION, FRONT...............23-186
DOOR OUTER BELT MOLDING -
INSTALLATION, REAR................23-186
DOOR OUTER BELT MOLDING -
REMOVAL, FRONT...................23-186
DOOR OUTER BELT MOLDING -
REMOVAL, REAR....................23-186
DOOR PRIMARY WEATHERSTRIP -
INSTALLATION......................23-185
DOOR PRIMARY WEATHERSTRIP -
REMOVAL.........................23-185
DOOR SCUFF PLATE - INSTALLATION,
REAR.............................23-160
DOOR SCUFF PLATE - REMOVAL, REAR . . 23-160
DOOR SILL SCUFF PLATE -
INSTALLATION......................23-157
DOOR SILL SCUFF PLATE - REMOVAL
. . . 23-157
DOOR/HOUSING - INSTALLATION, FUEL
FILL
..............................23-141
DOOR/HOUSING - REMOVAL, FUEL FILL
. 23-141
DOUBLE INVERTED FLARING -
STANDARD PROCEDURE
.................5-8
DRAIN AND FILL - STANDARD
PROCEDURE, FLUID
...........21-208,21-246DRAIN TUBE - INSTALLATION..........23-181
DRAIN TUBE - REMOVAL.............23-180
DRAINAGE AND WIND NOISE
DIAGNOSIS, DIAGNOSIS AND TESTING
- WATER ..........................23-176
DRAINING COOLING SYSTEM 3.7L
ENGINE - STANDARD PROCEDURE........7-12
DRAW TEST - STANDARD PROCEDURE,
IGNITION-OFF.......................8F-14
DRIVE - DIAGNOSIS AND TESTING,
VISCOUS FAN........................7-28
DRIVE BELT - DIAGNOSIS AND TESTING,
SERPENTINE.........................7-15
DRIVE MOTOR - INSTALLATION........23-182
DRIVE MOTOR - REMOVAL............23-182
DRIVER AIRBAG - DESCRIPTION........8O-17
DRIVER AIRBAG - INSTALLATION.......8O-20
DRIVER AIRBAG - OPERATION..........8O-18
DRIVER AIRBAG - REMOVAL...........8O-19
DRIVER SEAT HEATER SWITCH -
DESCRIPTION.......................8G-11
DRIVER SEAT HEATER SWITCH -
INSTALLATION......................8G-13
DRIVER SEAT HEATER SWITCH -
OPERATION.........................8G-12
DRIVER SEAT HEATER SWITCH -
REMOVAL..........................8G-13
DRIVER SIDE BEZELS - INSTALLATION,
INSTRUMENT PANEL.................23-154
DRIVER SIDE BEZELS - REMOVAL,
INSTRUMENT PANEL.................23-153
DROP - STANDARD PROCEDURE,
TESTING FOR A VOLTAGE...........8W-01-10
DRUM - DIAGNOSIS AND TESTING,
BRAKE..............................5-27
DRUM BRAKE - ADJUSTMENT, REAR......5-12
DRUM BRAKE - DESCRIPTION, REAR.....5-10
DRUM BRAKE - OPERATION, REAR.......5-11
DRUM BRAKE SHOES - INSTALLATION....5-11
DRUM BRAKE SHOES - REMOVAL........5-11
DRUM MACHINING - STANDARD
PROCEDURES, BRAKE.................5-27
DUCT - INSTALLATION, DEFROST/
DEMISTER..........................24-32
DUCT - INSTALLATION, FLOOR..........24-32
DUCT - INSTALLATION, FLOOR CONSOLE . 24-31
DUCT - REMOVAL, FLOOR.............24-32
DUCT - REMOVAL, FLOOR CONSOLE.....24-31
DUCT/DEMISTER ADAPTOR - REMOVAL,
DEFROST...........................24-32
EFFECTS OF INCORRECT FLUID LEVEL -
DIAGNOSIS AND TESTING............21-125
ELECTRIC - DESCRIPTION, RADIATOR
FAN ................................7-26
ELECTRIC - INSTALLATION, RADIATOR
FAN ................................7-27
ELECTRIC - INSTALLATION, WINDOW
REGULATOR.................23-126,23-134
ELECTRIC - OPERATION, RADIATOR FAN . . . 7-26
ELECTRIC - REMOVAL, RADIATOR FAN....7-26
ELECTRIC - REMOVAL, WINDOW
REGULATOR.................23-126,23-134
ELECTRICAL - DESCRIPTION............5-34
ELECTRICAL - OPERATION..............5-34
ELECTRICAL TESTER - STANDARD
PROCEDURE, USING MIDTRONICS.......8F-15
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE DEVICES - STANDARD
PROCEDURE......................8W-01-8
ELEMENT - DESCRIPTION, HEATED SEAT . 8G-13
ELEMENT - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-13
ELEMENT - OPERATION, HEATED SEAT . . . 8G-13
EMISSION CONTROL INFORMATION
(VECI) LABEL - DESCRIPTION,
VEHICLE..........................Intro.-8
EMISSION CONTROL SYSTEM -
DESCRIPTION........................25-1
END - INSTALLATION, TIE ROD.........19-16
END - REMOVAL, TIE ROD.............19-16
END CAP - INSTALLATION, INSTRUMENT
PANEL
............................23-153
END CAP - REMOVAL, INSTRUMENT
PANEL
............................23-153
END REMOVAL TOOL, SPECIAL TOOLS -
OUTER TIE ROD
.....................19-15
ENGINE - 3.7L - DESCRIPTION
............9-3
ENGINE - DESCRIPTION, 3.7L
............7-21
8 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

PRIMARY WEATHERSTRIP - REMOVAL,
DOOR............................23-185
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER........8N-9
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM................8E-1
PROGRAMMING - STANDARD
PROCEDURE, SENTRY KEY
TRANSPONDER.......................8Q-8
PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - FRONT -
INSTALLATION.........................3-6
PROPELLER SHAFT - FRONT - REMOVAL . . . 3-6
PROPELLER SHAFT - REAR -
INSTALLATION.........................3-7
PROPELLER SHAFT - REAR - REMOVAL....3-7
PROPELLER SHAFT ANGLE - STANDARD
PROCEDURES.........................3-3
PROPELLER SHAFT, SPECIFICATIONS.......3-6
PROPORTIONING VALVE - DIAGNOSIS
AND TESTING........................5-20
PULLEY - DESCRIPTION, GENERATOR
DECOUPLER........................8F-26
PULLEY - INSTALLATION..............19-23
PULLEY - INSTALLATION, GENERATOR
DECOUPLER........................8F-30
PULLEY - OPERATION, GENERATOR
DECOUPLER........................8F-27
PULLEY - REMOVAL..................19-23
PULLEY - REMOVAL, GENERATOR
DECOUPLER........................8F-27
PUMP - ASSEMBLY, OIL................9-67
PUMP - ASSEMBLY, OIL..............21-151
PUMP - CLEANING, OIL..............21-150
PUMP - DESCRIPTION................19-17
PUMP - DESCRIPTION, FUEL...........14-15
PUMP - DESCRIPTION, LEAK DETECTION . 25-27
PUMP - DESCRIPTION, OIL............21-147
PUMP - DESCRIPTION, WATER..........7-29
PUMP - DISASSEMBLY, OIL.............9-65
PUMP - DISASSEMBLY, OIL...........21-149
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-18
PUMP - INSPECTION, OIL...............9-66
PUMP - INSPECTION, OIL.............21-150
PUMP - INSTALLATION, LEAK
DETECTION.........................25-28
PUMP - INSTALLATION, OIL.............9-67
PUMP - OPERATION..................19-17
PUMP - OPERATION, FUEL.............14-15
PUMP - OPERATION, LEAK DETECTION . . . 25-28
PUMP - OPERATION, OIL.............21-147
PUMP - OPERATION, WATER............7-30
PUMP - REMOVAL, LEAK DETECTION....25-28
PUMP - REMOVAL, OIL.................9-65
PUMP AMPERAGE TEST - DIAGNOSIS
AND TESTING, FUEL..................14-16
PUMP CAPACITY TEST - DIAGNOSIS
AND TESTING, FUEL..................14-15
PUMP FRONT SEAL - INSTALLATION,
OIL...............................21-152
PUMP FRONT SEAL - REMOVAL, OIL....21-152
PUMP MODULE - DESCRIPTION, FUEL....14-18
PUMP MODULE - INSTALLATION, FUEL . . . 14-19
PUMP MODULE - OPERATION, FUEL.....14-18
PUMP MODULE - REMOVAL, FUEL.......14-18
PUMP PRESSURE TEST - DIAGNOSIS
AND TESTING, FUEL..................14-15
PUMP RELAY - DESCRIPTION, FUEL.....14-34
PUMP RELAY - DIAGNOSIS AND
TESTING, FUEL......................14-34
PUMP RELAY - INSTALLATION, FUEL.....14-34
PUMP RELAY - OPERATION, FUEL.......14-34
PUMP RELAY - REMOVAL, FUEL........14-34
PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD AND FUEL...............8I-4
PUMP, SPECIAL TOOLS - POWER
STEERING..........................19-20
PUMP VOLUME CHECK - STANDARD
PROCEDURE, OIL...................21-148
PUMP/MOTOR - DESCRIPTION, WASHER
. 8R-18
PUMP/MOTOR - INSTALLATION,
WASHER
...........................8R-20
PUMP/MOTOR - OPERATION, WASHER
. . . 8R-19
PUMP/MOTOR - REMOVAL, WASHER
....8R-19
QUARTER TRIM PANEL - INSTALLATION
. 23-159QUARTER TRIM PANEL - REMOVAL.....23-159
QUARTER WINDOW - INSTALLATION....23-172
QUARTER WINDOW - REMOVAL........23-172
QUICK CONNECT FITTING -
DESCRIPTION.......................14-10
QUICK LEARN - STANDARD
PROCEDURE, TCM...................8E-21
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE........................14-10
RACK - INSTALLATION, LUGGAGE......23-144
RACK - REMOVAL, LUGGAGE..........23-144
RADIAL-PLY TIRES - DESCRIPTION.......22-6
RADIATOR - CLEANING.................7-24
RADIATOR - DESCRIPTION..............7-22
RADIATOR - FAN - VISCOUS - CLEANING . . 7-29
RADIATOR - FAN - VISCOUS -
DESCRIPTION........................7-27
RADIATOR - FAN - VISCOUS -
INSPECTION.........................7-29
RADIATOR - FAN - VISCOUS -
INSTALLATION........................7-29
RADIATOR - FAN - VISCOUS -
OPERATION..........................7-27
RADIATOR - FAN - VISCOUS - REMOVAL . . . 7-28
RADIATOR - INSPECTION...............7-24
RADIATOR - INSTALLATION.............7-24
RADIATOR - REMOVAL.................7-23
RADIATOR CROSSMEMBER -
INSTALLATION......................23-146
RADIATOR CROSSMEMBER - REMOVAL . 23-146
RADIATOR FAN - ELECTRIC -
DESCRIPTION........................7-26
RADIATOR FAN - ELECTRIC -
INSTALLATION........................7-27
RADIATOR FAN - ELECTRIC -
OPERATION..........................7-26
RADIATOR FAN - ELECTRIC - REMOVAL . . . 7-26
RADIATOR PRESSURE CAP - CLEANING . . . 7-25
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-25
RADIATOR PRESSURE CAP - DIAGNOSIS
AND TESTING........................7-25
RADIATOR PRESSURE CAP -
INSPECTION.........................7-25
RADIATOR PRESSURE CAP - OPERATION . . 7-25
RADIO - DESCRIPTION.................8A-8
RADIO - INSTALLATION................8A-9
RADIO - OPERATION...................8A-8
RADIO - REMOVAL....................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - DESCRIPTION.................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - INSTALLATION...............8A-11
RADIO NOISE SUPPRESSION GROUND
STRAP - OPERATION.................8A-10
RADIO NOISE SUPPRESSION GROUND
STRAP - REMOVAL...................8A-10
RAIL - DESCRIPTION, FUEL............14-21
RAIL - INSTALLATION, FUEL............14-24
RAIL - OPERATION, FUEL..............14-21
RAIL - REMOVAL, FUEL...............14-22
RAIL WEATHERSTRIP/RETAINER -
INSTALLATION, SIDE.................23-186
RAIL WEATHERSTRIP/RETAINER -
REMOVAL, SIDE....................23-186
RAMP - INSTALLATION, WIPER ARM
PARK..............................8R-43
RAMP - REMOVAL, WIPER ARM PARK . . . 8R-43
RANGE INDICATOR ILLUMINATION BULB
- INSTALLATION, TRANSMISSION........8L-83
RANGE INDICATOR ILLUMINATION BULB
- REMOVAL, TRANSMISSION
...........8L-82
RANGE SENSOR - DESCRIPTION,
TRANSMISSION
.....................21-168
RANGE SENSOR - OPERATION,
TRANSMISSION
.....................21-168
RATINGS, GAS ENGINES - GENERATOR
. . . 8F-23
RBI AXLE - INSTALLATION, 198
..........5-28
RBI AXLE - REMOVAL, 198
..............5-27
READING LAMP BULB - INSTALLATION
. . . 8L-79
READING LAMP BULB - REMOVAL
.......8L-79
READING LAMP SWITCH -
INSTALLATION
.......................8L-80
READING LAMP SWITCH - REMOVAL
.....8L-80
READING LAMP UNIT - INSTALLATION
. . . 8L-81
READING LAMP UNIT - REMOVAL
.......8L-81
REAR - DESCRIPTION
..................2-16REAR - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-48
REAR - INSTALLATION, PROPELLER
SHAFT...............................3-7
REAR - INSTALLATION, SEAT..........23-168
REAR - INSTALLATION, SEAT BACK.....23-168
REAR - INSTALLATION, SEAT BACK
COVER............................23-169
REAR - INSTALLATION, SEAT BACK
CUSHION..........................23-170
REAR - INSTALLATION, SEAT BACK
FRAME............................23-171
REAR - INSTALLATION, SEAT CUSHION . . 23-171
REAR - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-48
REAR AXLE - 198RBI - DESCRIPTION.....3-49
REAR AXLE - 198RBI - INSTALLATION.....3-54
REAR AXLE - 198RBI - OPERATION.......3-49
REAR AXLE - 198RBI - REMOVAL........3-54
REAR AXLE - 8 1/4 - ADJUSTMENTS......3-92
REAR AXLE - 8 1/4 - DESCRIPTION.......3-86
REAR AXLE - 8 1/4 - INSTALLATION......3-91
REAR AXLE - 8 1/4 - OPERATION.........3-86
REAR AXLE - 8 1/4 - REMOVAL..........3-91
REAR AXLE - SPECIFICATIONS...........3-62
REAR AXLE, SPECIAL TOOLS............3-63
REAR AXLE, SPECIFICATIONS............3-98
REAR BRAKE HOSE - INSTALLATION......5-10
REAR BRAKE HOSE - REMOVAL...........5-9
REAR CENTER SEAT BELT &
RETRACTOR - INSTALLATION...........8O-33
REAR CENTER SEAT BELT &
RETRACTOR - REMOVAL..............8O-32
REAR CHECK VALVE - DESCRIPTION.....8R-34
REAR CHECK VALVE - INSTALLATION....8R-35
REAR CHECK VALVE - OPERATION.......8R-34
REAR CHECK VALVE - REMOVAL........8R-34
REAR CROSSMEMBER - INSTALLATION....13-7
REAR CROSSMEMBER - REMOVAL.......13-7
REAR DOOR OUTER BELT MOLDING -
INSTALLATION......................23-186
REAR DOOR OUTER BELT MOLDING -
REMOVAL.........................23-186
REAR DOOR SCUFF PLATE -
INSTALLATION......................23-160
REAR DOOR SCUFF PLATE - REMOVAL . . 23-160
REAR DRUM BRAKE - ADJUSTMENT......5-12
REAR DRUM BRAKE - DESCRIPTION......5-10
REAR DRUM BRAKE - OPERATION........5-11
REAR FASCIA - INSTALLATION...........13-2
REAR FASCIA - REMOVAL...............13-2
REAR FASCIA SUPPORT - INSTALLATION . . 13-3
REAR FASCIA SUPPORT - REMOVAL......13-3
REAR FOG LAMP INDICATOR -
DESCRIPTION.......................8J-27
REAR FOG LAMP INDICATOR -
OPERATION.........................8J-27
REAR FOG LAMP RELAY - DESCRIPTION . . 8L-56
REAR FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-57
REAR FOG LAMP RELAY -
INSTALLATION.......................8L-58
REAR FOG LAMP RELAY - OPERATION . . . 8L-57
REAR FOG LAMP RELAY - REMOVAL.....8L-58
REAR GLASS HEATING GRID REPAIR -
STANDARD PROCEDURE...............8G-4
REAR HVAC CONTROL ASSEMBLY
WINDOW DEFOGGER FUNCTION -
DIAGNOSIS AND TESTING..............8G-9
REAR LAMP BULB - INSTALLATION......8L-59
REAR LAMP BULB - REMOVAL..........8L-58
REAR LAMP UNIT - INSTALLATION......8L-60
REAR LAMP UNIT - REMOVAL..........8L-59
REAR MOUNT - INSTALLATION..........9-57
REAR MOUNT - REMOVAL..............9-57
REAR OUTBOARD SEAT BELT &
RETRACTOR - INSTALLATION...........8O-34
REAR OUTBOARD SEAT BELT &
RETRACTOR - REMOVAL..............8O-33
REAR OUTPUT SHAFT SEAL -
INSTALLATION
......................21-212
REAR OUTPUT SHAFT SEAL - REMOVAL
. 21-210
REAR SEAL AREA LEAKS - DIAGNOSIS
AND TESTING
........................9-61
REAR SEAT BACK LATCH / LOCK -
INSTALLATION, FOLDING
.............23-170
REAR SEAT BACK LATCH / LOCK -
REMOVAL, FOLDING
.................23-170
20 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

VALVE - INSTALLATION, FLOW
MANAGEMENT.......................14-7
VALVE - INSTALLATION, FRONT CHECK....8R-9
VALVE - INSTALLATION, FUEL TANK
CHECK.............................14-28
VALVE - INSTALLATION, PCV...........25-32
VALVE - INSTALLATION, REAR CHECK....8R-35
VALVE - INSTALLATION, VACUUM CHECK . 24-28
VALVE - OPERATION, FLOW
MANAGEMENT.......................14-6
VALVE - OPERATION, FRONT CHECK......8R-9
VALVE - OPERATION, FUEL TANK CHECK . . 14-28
VALVE - OPERATION, HIGH PRESSURE
RELIEF.............................24-42
VALVE - OPERATION, PCV..............25-31
VALVE - OPERATION, REAR CHECK......8R-34
VALVE - OPERATION, SOLENOID SWITCH . 21-161
VALVE - OPERATION, VACUUM CHECK....24-28
VALVE - REMOVAL, FLOW
MANAGEMENT.......................14-6
VALVE - REMOVAL, FRONT CHECK.......8R-9
VALVE - REMOVAL, FUEL TANK CHECK . . . 14-28
VALVE - REMOVAL, PCV...............25-32
VALVE - REMOVAL, REAR CHECK.......8R-34
VALVE - REMOVAL, VACUUM CHECK.....24-28
VALVE BODY - ASSEMBLY............21-176
VALVE BODY - CLEANING.............21-175
VALVE BODY - DESCRIPTION............21-171
VALVE BODY - DISASSEMBLY..........21-173
VALVE BODY - INSPECTION...........21-175
VALVE BODY - INSTALLATION..........21-177
VALVE BODY - OPERATION............21-171
VALVE BODY - REMOVAL.............21-172
VALVE GUIDE SEALS - DESCRIPTION . . 9-29,9-38
VALVE GUIDES - DESCRIPTION......9-19,9-30
VALVE SPRINGS - DESCRIPTION.....9-29,9-38
VALVE SPRINGS - INSTALLATION.....9-29,9-38
VALVE SPRINGS - REMOVAL........9-29,9-38
VALVE TIMING - DESCRIPTION...........9-71
VALVE TIMING - OPERATION............9-71
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST.................9-28,9-36
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST.................9-27,9-35
VANITY LAMP BULB - INSTALLATION.....8L-84
VANITY LAMP BULB - REMOVAL........8L-83
VAPOR CANISTER - DESCRIPTION.......25-33
VAPOR CANISTER - INSTALLATION......25-33
VAPOR CANISTER - OPERATION.........25-33
VAPOR CANISTER - REMOVAL..........25-33
VARIATION ADJUSTMENT - STANDARD
PROCEDURE, COMPASS...............8M-3
VEHICLE EMISSION CONTROL
INFORMATION (VECI) LABEL -
DESCRIPTION......................Intro.-8
VEHICLE IDENTIFICATION NUMBER -
DESCRIPTION......................Intro.-8
VEHICLE SAFETY CERTIFICATION LABEL
- DESCRIPTION.....................Intro.-9
VEHICLE THEFT SECURITY -
DESCRIPTION........................8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-3
VEHICLE THEFT SECURITY SYSTEM -
DIAGNOSIS AND TESTING..............8Q-6
VERIFICATION TEST - STANDARD
PROCEDURE.........................8O-8
VIBRATION - DIAGNOSIS AND TESTING,
TIRE NOISE OR.......................22-8
VIBRATION DAMPER - INSTALLATION.....9-55
VIBRATION DAMPER - REMOVAL.........9-54
VIEW MIRROR - INSTALLATION, SIDE . . . 23-145
VIEW MIRROR - REMOVAL, REAR......23-161
VIEW MIRROR - REMOVAL, SIDE.......23-145
VISCOUS - CLEANING, RADIATOR - FAN . . . 7-29
VISCOUS - DESCRIPTION, RADIATOR -
FAN ................................7-27
VISCOUS - INSPECTION, RADIATOR -
FAN ................................7-29
VISCOUS - INSTALLATION, RADIATOR -
FAN
................................7-29
VISCOUS - OPERATION, RADIATOR -
FAN
................................7-27
VISCOUS - REMOVAL, RADIATOR - FAN
....7-28
VISCOUS FAN DRIVE - DIAGNOSIS AND
TESTING
............................7-28
VISOR - INSTALLATION, SUN
..........23-160VISOR - REMOVAL, SUN..............23-160
VISOR SUPPORT - INSTALLATION, SUN . . 23-160
VISOR SUPPORT - REMOVAL, SUN.....23-160
VOLT SUPPLIES - DESCRIPTION, 5......8E-13
VOLT SUPPLIES - OPERATION, 5........8E-15
VOLTAGE DROP - STANDARD
PROCEDURE, TESTING FOR A.......8W-01-10
VOLTAGE POTENTIAL - STANDARD
PROCEDURE, TESTING OF...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION....8F-31
VOLTAGE REGULATOR - OPERATION.....8F-31
VOLTAGE TEST - STANDARD
PROCEDURE, OPEN-CIRCUIT...........8F-12
VOLUME CHECK - STANDARD
PROCEDURE, OIL PUMP..............21-148
WAIT-TO-START INDICATOR -
DESCRIPTION.......................8J-35
WAIT-TO-START INDICATOR -
OPERATION.........................8J-35
WARNING - INSTALLATION............23-173
WARNING - REMOVAL...............23-173
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - SERVICE WARNINGS........24-39
WARNING - WINDSHIELD SAFETY
PRECAUTIONS......................23-173
WARNING, BRAKES - BASE..............5-2
WARNING, CLUTCH.....................6-2
WARNING, FRONT......................2-7
WARNING, REAR......................2-16
WARNING, RESTRAINT SYSTEM.........8O-5
WARNING SYSTEM - DESCRIPTION,
CHIME..............................8B-1
WARNING SYSTEM - DIAGNOSIS AND
TESTING, CHIME......................8B-6
WARNING SYSTEM - OPERATION,
CHIME..............................8B-2
WARNINGS, GENERAL..............8W-01-7
WARNINGS, WARNING - SAFETY
PRECAUTIONS........................23-1
WARNINGS, WARNING - SERVICE.......24-39
WASHER FLUID INDICATOR -
DESCRIPTION.......................8J-35
WASHER FLUID INDICATOR -
DIAGNOSIS AND TESTING..............8J-36
WASHER FLUID INDICATOR -
OPERATION.........................8J-36
WASHER FLUID LEVEL SWITCH -
DESCRIPTION.......................8R-17
WASHER FLUID LEVEL SWITCH -
INSTALLATION......................8R-18
WASHER FLUID LEVEL SWITCH -
OPERATION.........................8R-17
WASHER FLUID LEVEL SWITCH -
REMOVAL..........................8R-17
WASHER HOSES/TUBES - DESCRIPTION,
FRONT.............................8R-10
WASHER HOSES/TUBES - DESCRIPTION,
REAR..............................8R-35
WASHER HOSES/TUBES - OPERATION,
FRONT.............................8R-10
WASHER HOSES/TUBES - OPERATION,
REAR..............................8R-36
WASHER NOZZLE - DESCRIPTION,
FRONT.............................8R-11
WASHER NOZZLE - DESCRIPTION, REAR . 8R-36
WASHER NOZZLE - INSTALLATION,
FRONT.............................8R-11
WASHER NOZZLE - INSTALLATION,
REAR..............................8R-37
WASHER NOZZLE - OPERATION, FRONT . . 8R-11
WASHER NOZZLE - OPERATION, REAR . . . 8R-36
WASHER NOZZLE - REMOVAL, FRONT....8R-11
WASHER NOZZLE - REMOVAL, REAR....8R-36
WASHER PUMP/MOTOR - DESCRIPTION . . 8R-18
WASHER PUMP/MOTOR - INSTALLATION . 8R-20
WASHER PUMP/MOTOR - OPERATION . . . 8R-19
WASHER PUMP/MOTOR - REMOVAL.....8R-19
WASHER RESERVOIR - DESCRIPTION....8R-21
WASHER RESERVOIR - INSTALLATION . . . 8R-22
WASHER RESERVOIR - OPERATION
......8R-21
WASHER RESERVOIR - REMOVAL
.......8R-21
WASHER SYSTEM - CLEANING, FRONT
WIPER
..............................8R-7
WASHER SYSTEM - CLEANING, REAR
WIPER
.............................8R-32
WASHER SYSTEM - DIAGNOSIS AND
TESTING, FRONT WIPER
...............8R-6WASHER SYSTEM - DIAGNOSIS AND
TESTING, REAR WIPER...............8R-30
WASHER SYSTEM - INSPECTION, FRONT
WIPER..............................8R-7
WASHER SYSTEM - INSPECTION, REAR
WIPER.............................8R-33
WATER DRAINAGE AND WIND NOISE
DIAGNOSIS, DIAGNOSIS AND TESTING . . 23-176
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-2
WATER PUMP - DESCRIPTION...........7-29
WATER PUMP - OPERATION.............7-30
WATERDAM - INSTALLATION....23-126,23-133
WATERDAM - REMOVAL........23-126,23-133
WATER-IN-FUEL INDICATOR -
DESCRIPTION.......................8J-37
WATER-IN-FUEL INDICATOR -
OPERATION.........................8J-37
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD......................22-8
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE.......................22-8
WEAR, STANDARD PROCEDURE -
MEASURING TIMING CHAIN.............9-71
WEATHERSTRIP - INSTALLATION, COWL . 23-185
WEATHERSTRIP - INSTALLATION, DOOR
LOWER...........................23-186
WEATHERSTRIP - INSTALLATION, DOOR
PRIMARY..........................23-185
WEATHERSTRIP - INSTALLATION,
SWING GATE BELTLINE...............23-186
WEATHERSTRIP - INSTALLATION,
SWING GATE OPENING...............23-186
WEATHERSTRIP - REMOVAL, COWL.....23-185
WEATHERSTRIP - REMOVAL, DOOR
LOWER...........................23-186
WEATHERSTRIP - REMOVAL, DOOR
PRIMARY..........................23-185
WEATHERSTRIP - REMOVAL, SWING
GATE BELTLINE.....................23-186
WEATHERSTRIP - REMOVAL, SWING
GATE OPENING.....................23-186
WEATHERSTRIP/RETAINER -
INSTALLATION, SIDE RAIL............23-186
WEATHERSTRIP/RETAINER -
INSTALLATION, WINDSHIELD A-PILLAR . . 23-187
WEATHERSTRIP/RETAINER - REMOVAL,
SIDE RAIL.........................23-186
WEATHERSTRIP/RETAINER - REMOVAL,
WINDSHIELD A-PILLAR...............23-186
WELD AND STRUCTURAL ADHESIVE
LOCATIONS - SPECIFICATIONS...........23-9
WHEEL - INSTALLATION, STEERING......19-12
WHEEL - REMOVAL, STEERING.........19-12
WHEEL ALIGNMENT - DESCRIPTION.......2-3
WHEEL ALIGNMENT - OPERATION.........2-3
WHEEL BALANCING - STANDARD
PROCEDURE.........................22-4
WHEEL CYLINDERS - ASSEMBLY.........5-29
WHEEL CYLINDERS - CLEANING.........5-28
WHEEL CYLINDERS - DISASSEMBLY......5-28
WHEEL CYLINDERS - INSPECTION........5-29
WHEEL CYLINDERS - INSTALLATION......5-29
WHEEL CYLINDERS - REMOVAL..........5-28
WHEEL MOUNTING - STANDARD
PROCEDURE........................22-10
WHEEL OPENING FLARE MOLDINGS -
INSTALLATION, FRONT...............23-145
WHEEL OPENING FLARE MOLDINGS -
INSTALLATION, REAR................23-145
WHEEL OPENING FLARE MOLDINGS -
REMOVAL, FRONT...................23-145
WHEEL OPENING FLARE MOLDINGS -
REMOVAL, REAR....................23-145
WHEEL REPLACEMENT - STANDARD
PROCEDURE........................22-10
WHEEL RUNOUT - DIAGNOSIS AND
TESTING, TIRES......................22-1
WHEEL SPEED SENSOR -
INSTALLATION, FRONT
.................5-34
WHEEL SPEED SENSOR -
INSTALLATION, REAR
..................5-35
WHEEL SPEED SENSOR - REMOVAL,
FRONT
..............................5-34
WHEEL SPEED SENSOR - REMOVAL,
REAR
...............................5-35
WHEELHOUSE SPLASH SHIELD -
INSTALLATION, FRONT
...............23-143
KJINDEX 29
Description Group-Page Description Group-Page Description Group-Page

COOLANT TEMPERATURE SENSOR -
OPERATION, ENGINE...................7-21
COOLANT TEMPERATURE SENSOR -
REMOVAL, ENGINE....................7-21
COOLER - DESCRIPTION, TRANS.........7-30
COOLERS AND TUBES - STANDARD
PROCEDURE, FLUSHING................7-30
COOLING, SPECIAL TOOLS..............7-13
COOLING SYSTEM - OPERATION..........7-2
COOLING SYSTEM - REVERSE
FLUSHING - STANDARD PROCEDURE.....7-12
COOLING SYSTEM - STANDARD
PROCEDURE, DRAINING................7-11
COOLING SYSTEM - STANDARD
PROCEDURE, REFILLING................7-11
COOLING SYSTEM 2.4L ENGINE -
DESCRIPTION.........................7-1
COOLING SYSTEM DIAGNOSIS CHART -
DIAGNOSIS AND TESTING...............7-5
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING.........................7-2
CORE AND OIL GALLERY PLUGS -
STANDARD PROCEDURE, ENGINE.........9-9
COVER - CLEANING, CYLINDER HEAD.....9-26
COVER - INSPECTION, CYLINDER HEAD . . . 9-26
COVER - INSTALLATION, CYLINDER
HEAD...............................9-26
COVER - REMOVAL, CYLINDER HEAD.....9-26
COVER(S) - INSTALLATION, TIMING
BELT ...............................9-53
COVER(S) - REMOVAL, TIMING BELT......9-53
CRANKSHAFT - DESCRIPTION...........9-32
CRANKSHAFT - INSPECTION.............9-34
CRANKSHAFT - INSTALLATION...........9-34
CRANKSHAFT - OPERATION.............9-33
CRANKSHAFT - REMOVAL..............9-33
CRANKSHAFT END PLAY - STANDARD
PROCEDURE.........................9-33
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION........................9-37
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL...........................9-37
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION........................9-39
CRANKSHAFT OIL SEAL - REAR -
REMOVAL...........................9-38
CRANKSHAFT SPROCKET -
INSTALLATION........................9-56
CRANKSHAFT SPROCKET - REMOVAL.....9-55
CROSS-OVER PIPE - INSTALLATION.......11-4
CROSS-OVER PIPE - REMOVAL..........11-4
CYLINDER BORE FITTING - STANDARD
PROCEDURE, PISTON TO...............9-30
CYLINDER BORE HONING - STANDARD
PROCEDURE.........................9-31
CYLINDER COMBUSTION PRESSURE
LEAKAGE TEST - DIAGNOSIS AND
TESTING.............................9-3
CYLINDER COMPRESSION PRESSURE
TEST - DIAGNOSIS AND TESTING.........9-3
CYLINDER HEAD - CLEANING............9-20
CYLINDER HEAD - DESCRIPTION.........9-19
CYLINDER HEAD - INSPECTION..........9-21
CYLINDER HEAD - INSTALLATION........9-21
CYLINDER HEAD - OPERATION...........9-19
CYLINDER HEAD - REMOVAL............9-20
CYLINDER HEAD COVER - CLEANING......9-26
CYLINDER HEAD COVER - INSPECTION....9-26
CYLINDER HEAD COVER -
INSTALLATION
........................9-26
CYLINDER HEAD COVER - REMOVAL
......9-26
CYLINDER HEAD GASKET - DIAGNOSIS
AND TESTING
........................9-19
CYLINDER HEAD OFF - INSTALLATION
.....9-28
CYLINDER HEAD OFF - REMOVAL
........9-27
CYLINDER HEAD ON - INSTALLATION
.....9-28
CYLINDER HEAD ON - REMOVAL
.........9-27
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE, REPAIR OF
.......9-9
DAMPER - INSTALLATION, VIBRATION
.....9-43
DAMPER - REMOVAL, VIBRATION
........9-43
DAYTIME RUNNING LAMP RELAY -
DESCRIPTION
.......................8L-20
DAYTIME RUNNING LAMP RELAY -
INSTALLATION
.......................8L-21
DAYTIME RUNNING LAMP RELAY -
OPERATION
.........................8L-20DAYTIME RUNNING LAMP RELAY -
REMOVAL..........................8L-21
DESCRIPTION - OPERATION.............7-20
DESCRIPTION, BACKUP LAMP SWITCH . . . 8L-15
DESCRIPTION, BALANCE SHAFT..........9-59
DESCRIPTION, BRAKE LAMP SWITCH....8L-16
DESCRIPTION, CAMSHAFT(S)............9-23
DESCRIPTION, CATALYTIC CONVERTER....11-2
DESCRIPTION, COMBINATION FLASHER . . . 8L-19
DESCRIPTION, COOLANT RECOVERY
PRESS CONTAINER....................7-20
DESCRIPTION, COOLING SYSTEM 2.4L
ENGINE..............................7-1
DESCRIPTION, CRANKSHAFT............9-32
DESCRIPTION, CYLINDER HEAD..........9-19
DESCRIPTION, DAYTIME RUNNING
LAMP RELAY........................8L-20
DESCRIPTION, ENGINE - 2.4L.............9-3
DESCRIPTION, ENGINE BLOCK...........9-30
DESCRIPTION, ENGINE BLOCK HEATER -
2.4L................................7-20
DESCRIPTION, ENGINE COOLANT.........7-19
DESCRIPTION, ENGINE COOLANT
TEMPERATURE SENSOR................7-21
DESCRIPTION, ENGINE MOUNTING.......9-44
DESCRIPTION, EXHAUST MANIFOLD......9-53
DESCRIPTION, EXHAUST SYSTEM........11-1
DESCRIPTION, FRONT FOG LAMP RELAY . . 8L-22
DESCRIPTION, HAZARD SWITCH........8L-28
DESCRIPTION, HEADLAMP HIGH BEAM
RELAY.............................8L-33
DESCRIPTION, HEADLAMP LEVELING
MOTOR............................8L-35
DESCRIPTION, HEADLAMP LEVELING
SWITCH............................8L-37
DESCRIPTION, HEADLAMP LOW BEAM
RELAY.............................8L-39
DESCRIPTION, HEAT SHIELDS...........11-4
DESCRIPTION, HOAT COOLANT..........7-18
DESCRIPTION, HOSE CLAMPS............7-1
DESCRIPTION, INTAKE MANIFOLD........9-51
DESCRIPTION, INTAKE/EXHAUST VALVES
& SEATS ............................9-27
DESCRIPTION, LAMP BAR.............8L-65
DESCRIPTION, LAMP BAR SWITCH......8L-67
DESCRIPTION, LAMPS/LIGHTING -
EXTERIOR...........................8L-2
DESCRIPTION, LUBRICATION............9-46
DESCRIPTION, MUFFLER...............11-4
DESCRIPTION, MULTI-FUNCTION
SWITCH............................8L-46
DESCRIPTION, OIL FILTER..............9-47
DESCRIPTION, OIL PRESSURE
SENSOR/SWITCH.....................9-48
DESCRIPTION, PARK LAMP RELAY.......8L-54
DESCRIPTION, PISTON & CONNECTING
ROD................................9-40
DESCRIPTION, RADIATOR...............7-22
DESCRIPTION, RADIATOR FAN -
ELECTRIC...........................7-26
DESCRIPTION, RADIATOR PRESSURE
CAP ................................7-25
DESCRIPTION, REAR FOG LAMP RELAY . . . 8L-56
DESCRIPTION, TRAILER TOW RELAY.....8L-62
DESCRIPTION, TRAILER TOW WIRING....8L-64
DESCRIPTION, TRANS COOLER..........7-30
DESCRIPTION, WATER PUMP - 2.4L......7-27
DIAGNOSIS - DIAGNOSIS AND TESTING,
LASH ADJUSTER (TAPPET) NOISE........9-28
DIAGNOSIS - DIAGNOSIS AND TESTING,
SERPENTINE DRIVE BELT...............7-15
DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING, ENGINE........9-5
DIAGNOSIS AND TESTING, BACKUP
LAMP SWITCH......................8L-15
DIAGNOSIS AND TESTING, BRAKE LAMP
SWITCH............................8L-17
DIAGNOSIS AND TESTING, COOLING
SYSTEM DIAGNOSIS CHART
..............7-5
DIAGNOSIS AND TESTING, COOLING
SYSTEM LEAKS
........................7-2
DIAGNOSIS AND TESTING, CYLINDER
COMBUSTION PRESSURE LEAKAGE
TEST
................................9-3
DIAGNOSIS AND TESTING, CYLINDER
COMPRESSION PRESSURE TEST
..........9-3
DIAGNOSIS AND TESTING, CYLINDER
HEAD GASKET
........................9-19DIAGNOSIS AND TESTING, ENGINE........9-5
DIAGNOSIS AND TESTING, ENGINE
DIAGNOSIS - PERFORMANCE.............9-5
DIAGNOSIS AND TESTING, ENGINE
MECHANICAL.........................9-7
DIAGNOSIS AND TESTING, ENGINE OIL
LEAK INSPECTION......................9-4
DIAGNOSIS AND TESTING, ENGINE OIL
PRESSURE CHECKING.................9-46
DIAGNOSIS AND TESTING, EXHAUST
SYSTEM............................11-2
DIAGNOSIS AND TESTING, FRONT FOG
LAMP RELAY........................8L-23
DIAGNOSIS AND TESTING, HEADLAMP
HIGH BEAM RELAY...................8L-34
DIAGNOSIS AND TESTING, HEADLAMP
LEVELING SWITCH...................8L-37
DIAGNOSIS AND TESTING, HEADLAMP
LOW BEAM RELAY...................8L-40
DIAGNOSIS AND TESTING, INTAKE
MANIFOLD LEAKS.....................9-51
DIAGNOSIS AND TESTING, LAMP BAR....8L-65
DIAGNOSIS AND TESTING, LAMPS/
LIGHTING - EXTERIOR.................8L-7
DIAGNOSIS AND TESTING, LASH
ADJUSTER (TAPPET) NOISE
DIAGNOSIS..........................9-28
DIAGNOSIS AND TESTING, MULTI-
FUNCTION SWITCH...................8L-50
DIAGNOSIS AND TESTING, ON-BOARD
DIAGNOSTICS (OBD)....................7-2
DIAGNOSIS AND TESTING, PARK LAMP
RELAY.............................8L-55
DIAGNOSIS AND TESTING,
PRELIMINARY CHECKS..................7-2
DIAGNOSIS AND TESTING, RADIATOR
PRESSURE CAP.......................7-25
DIAGNOSIS AND TESTING, REAR FOG
LAMP RELAY........................8L-57
DIAGNOSIS AND TESTING, SERPENTINE
DRIVE BELT DIAGNOSIS................7-15
DIAGNOSIS AND TESTING, TRAILER
TOW RELAY.........................8L-62
DIAGNOSIS CHART - DIAGNOSIS AND
TESTING, COOLING SYSTEM.............7-5
DIAGNOSTICS (OBD) - DIAGNOSIS AND
TESTING, ON-BOARD...................7-2
DISASSEMBLY, OIL PUMP...............9-49
DRAINING COOLING SYSTEM -
STANDARD PROCEDURE................7-11
DRIVE BELT DIAGNOSIS - DIAGNOSIS
AND TESTING, SERPENTINE.............7-15
ELECTRIC - DESCRIPTION, RADIATOR
FAN ................................7-26
ELECTRIC - INSTALLATION, RADIATOR
FAN ................................7-27
ELECTRIC - OPERATION, RADIATOR FAN . . . 7-26
ELECTRIC - REMOVAL, RADIATOR FAN....7-26
END PLAY - STANDARD PROCEDURE,
CRANKSHAFT........................9-33
END-PLAY - STANDARD PROCEDURE,
CAMSHAFT..........................9-23
ENGINE - 2.4L - DESCRIPTION............9-3
ENGINE - DESCRIPTION, COOLING
SYSTEM 2.4L.........................7-1
ENGINE - DIAGNOSIS AND TESTING.......9-5
ENGINE - INSTALLATION, 2.4L . . 7-14,7-17,7-22,
7-28
ENGINE - REMOVAL, 2.4L . . . 7-14,7-16,7-22,7-27
ENGINE - SPECIFICATIONS, 2.4L.........9-13
ENGINE - STANDARD PROCEDURE,
HYDROSTATIC LOCKED..................9-9
ENGINE ASSEMBLY - INSTALLATION......9-12
ENGINE ASSEMBLY - REMOVAL..........9-12
ENGINE BLOCK - DESCRIPTION..........9-30
ENGINE BLOCK HEATER - 2.4L -
DESCRIPTION........................7-20
ENGINE BLOCK HEATER - 2.4L -
OPERATION..........................7-20
ENGINE COOLANT - DESCRIPTION
........7-19
ENGINE COOLANT TEMPERATURE
SENSOR - DESCRIPTION
...............7-21
ENGINE COOLANT TEMPERATURE
SENSOR - INSTALLATION
...............7-22
ENGINE COOLANT TEMPERATURE
SENSOR - OPERATION
.................7-21
ENGINE COOLANT TEMPERATURE
SENSOR - REMOVAL
...................7-21
2 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page