2002 JEEP LIBERTY Change JB

fuel gas tank size transmission sensor roof rack start stop button

Page 1727 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual OPERATION - TASK MANAGER
The Task Manager determines which tests happen
when and which functions occur when. Many of the
diagnostic steps required by OBD II must be per-
formed under specific operatin

OPERATION - TASK MANAGER
The Task Manager determines which tests happen
when and which functions occur when. Many of the
diagnostic steps required by OBD II must be per-
formed under specific operating conditions. The Task
Manager software organizes and prioritizes the diag-
nostic procedures. The job of the Task Manager is to
determine if conditions are appropriate for tests to be
run, monitor the parameters for a trip for each test,
and record the results of the test. Following are the
responsibilities of the Task Manager software:
²Test Sequence
²MIL Illumination
²Diagnostic Trouble Codes (DTCs)
²Trip Indicator
²Freeze Frame Data Storage
²Similar Conditions Window
Test Sequence
In many instances, emissions systems must fail
diagnostic tests more than once before the PCM illu-
minates the MIL. These tests are know as 'two trip
monitors.' Other tests that turn the MIL lamp on
after a single failure are known as 'one trip moni-
tors.' A trip is defined as 'start the vehicle and oper-
ate it to meet the criteria necessary to run the given
monitor.'
Many of the diagnostic tests must be performed
under certain operating conditions. However, there
are times when tests cannot be run because another
test is in progress (conflict), another test has failed
(pending) or the Task Manager has set a fault that
may cause a failure of the test (suspend).
²Pending
Under some situations the Task Manager will not
run a monitor if the MIL is illuminated and a fault is
stored from another monitor. In these situations, the
Task Manager postpones monitorspendingresolu-
tion of the original fault. The Task Manager does not
run the test until the problem is remedied.
For example, when the MIL is illuminated for an
Oxygen Sensor fault, the Task Manager does not run
the Catalyst Monitor until the Oxygen Sensor fault is
remedied. Since the Catalyst Monitor is based on sig-
nals from the Oxygen Sensor, running the test would
produce inaccurate results.
²Conflict
There are situations when the Task Manager does
not run a test if another monitor is in progress. In
these situations, the effects of another monitor run-
ning could result in an erroneous failure. If thiscon-
flictis present, the monitor is not run until the
conflicting condition passes. Most likely the monitor
will run later after the conflicting monitor has
passed.For example, if the Fuel System Monitor is in
progress, the Task Manager does not run the EGR
Monitor. Since both tests monitor changes in air/fuel
ratio and adaptive fuel compensation, the monitors
will conflict with each other.
²Suspend
Occasionally the Task Manager may not allow a two
trip fault to mature. The Task Manager willsus-
pendthe maturing of a fault if a condition exists
that may induce an erroneous failure. This prevents
illuminating the MIL for the wrong fault and allows
more precis diagnosis.
For example, if the PCM is storing a one trip fault
for the Oxygen Sensor and the EGR monitor, the
Task Manager may still run the EGR Monitor but
will suspend the results until the Oxygen Sensor
Monitor either passes or fails. At that point the Task
Manager can determine if the EGR system is actu-
ally failing or if an Oxygen Sensor is failing.MIL Illumination
The PCM Task Manager carries out the illumina-
tion of the MIL. The Task Manager triggers MIL illu-
mination upon test failure, depending on monitor
failure criteria.
The Task Manager Screen shows both a Requested
MIL state and an Actual MIL state. When the MIL is
illuminated upon completion of a test for a third trip,
the Requested MIL state changes to OFF. However,
the MIL remains illuminated until the next key
cycle. (On some vehicles, the MIL will actually turn
OFF during the third key cycle) During the key cycle
for the third good trip, the Requested MIL state is
OFF, while the Actual MIL state is ON. After the
next key cycle, the MIL is not illuminated and both
MIL states read OFF.
Diagnostic Trouble Codes (DTCs)
With OBD II, different DTC faults have different
priorities according to regulations. As a result, the
priorities determine MIL illumination and DTC era-
sure. DTCs are entered according to individual prior-
ity. DTCs with a higher priority overwrite lower
priority DTCs.
Priorities
²Priority 0 ÐNon-emissions related trouble codes
²Priority 1 Ð One trip failure of a two trip fault
for non-fuel system and non-misfire.
²Priority 2 Ð One trip failure of a two trip fault
for fuel system (rich/lean) or misfire.
²Priority3ÐTwotrip failure for a non-fuel sys-
tem and non-misfire or matured one trip comprehen-
sive component fault.
KJEMISSIONS CONTROL 25 - 21
EMISSIONS CONTROL (Continued)

Page 1744 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual CASE BEARINGS - REMOVAL,
DIFFERENTIAL...............3-110,3-43,3-79
CASE, NV231 - TRANSFER............21-206
CASE, NV242 - TRANSFER............21-244
CASE SKID PLATE - INSTALLATION,
TRANSFER..........

CASE BEARINGS - REMOVAL,
DIFFERENTIAL...............3-110,3-43,3-79
CASE, NV231 - TRANSFER............21-206
CASE, NV242 - TRANSFER............21-244
CASE SKID PLATE - INSTALLATION,
TRANSFER...........................13-7
CASE SKID PLATE - REMOVAL,
TRANSFER...........................13-7
CASE, SPECIFICATIONS - NV242
TRANSFER.........................21-244
CASTER ADJUSTMENT - STANDARD
PROCEDURE, CAMBER..................2-5
CASTER AND TOE ADJUSTMENT -
STANDARD PROCEDURE, CAMBER........2-5
CATALYTIC CONVERTER - DESCRIPTION . . . 11-2
CATALYTIC CONVERTER - INSPECTION....11-3
CATALYTIC CONVERTER - INSTALLATION . . . 11-3
CATALYTIC CONVERTER - REMOVAL......11-2
CAUSES OF BURNT FLUID - DIAGNOSIS
AND TESTING......................21-125
CAUTION - SERVICE CAUTIONS.........24-39
CAUTION, HALF SHAFT.................3-10
CAUTION, REFRIGERANT HOSES/LINES/
TUBES PRECAUTIONS.................24-40
CAUTIONS, CAUTION - SERVICE.........24-39
CD CHANGER - DESCRIPTION...........8A-7
CD CHANGER - INSTALLATION...........8A-7
CD CHANGER - OPERATION.............8A-7
CD CHANGER - REMOVAL..............8A-7
CENTER - DESCRIPTION, POWER
DISTRIBUTION....................8W-97-6
CENTER - OPERATION, POWER
DISTRIBUTION....................8W-97-7
CENTER - REMOVAL, POWER
DISTRIBUTION....................8W-97-7
CENTER ASSEMBLY, ASSEMBLY -
POWER DISTRIBUTION.............8W-97-10
CENTER BEZEL - INSTALLATION,
INSTRUMENT PANEL.................23-154
CENTER BEZEL - REMOVAL,
INSTRUMENT PANEL.................23-154
CENTER DISASSEMBLY, DISASSEMBLY -
POWER DISTRIBUTION..............8W-97-7
CENTER HIGH MOUNTED STOP LAMP
BULB - INSTALLATION................8L-19
CENTER HIGH MOUNTED STOP LAMP
BULB - REMOVAL....................8L-18
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION.................8L-19
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL....................8L-19
CENTER SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-33
CENTER SEAT BELT & RETRACTOR -
REMOVAL, REAR....................8O-32
CENTERING - STANDARD PROCEDURE,
CLOCKSPRING......................8O-14
CERTIFICATION LABEL - DESCRIPTION,
VEHICLE SAFETY...................Intro.-9
CHAIN COVER(S) - INSTALLATION,
TIMING BELT.........................9-76
CHAIN COVER(S) - REMOVAL, TIMING
BELT ...............................9-74
CHAIN WEAR, STANDARD PROCEDURE -
MEASURING TIMING...................9-71
CHANGER - DESCRIPTION, CD...........8A-7
CHANGER - INSTALLATION, CD..........8A-7
CHANGER - OPERATION, CD.............8A-7
CHANGER - REMOVAL, CD..............8A-7
CHANNEL - INSTALLATION, GLASS RUN . 23-123,
23-130
CHANNEL - REMOVAL, GLASS RUN....23-123,
23-130
CHARGE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-41
CHARGE CAPACITY - SPECIFICATIONS....24-42
CHARGING - STANDARD PROCEDURE,
BATTERY............................8F-8
CHARGING INDICATOR - DESCRIPTION . . . 8J-15
CHARGING INDICATOR - OPERATION.....8J-15
CHARGING SYSTEM - DESCRIPTION
.....8F-22
CHARGING SYSTEM - DIAGNOSIS AND
TESTING
...........................8F-22
CHARGING SYSTEM - OPERATION
.......8F-22
CHART - DIAGNOSIS AND TESTING,
COOLING SYSTEM DIAGNOSIS
............7-6
CHART, SPECIFICATIONS - TORQUE
.....19-15,
19-19,19-8CHART, SPECIFICATIONS - TORQUE....2-17,2-8
CHECK - STANDARD PROCEDURE, FLUID
LEVEL............................21-126
CHECK - STANDARD PROCEDURE, OIL
PUMP VOLUME.....................21-148
CHECK STRAP - INSTALLATION . . 23-121,23-128,
23-135
CHECK STRAP - REMOVAL.....23-121,23-128,
23-135
CHECK VALVE - DESCRIPTION, FRONT....8R-8
CHECK VALVE - DESCRIPTION, FUEL
TANK ..............................14-28
CHECK VALVE - DESCRIPTION, REAR....8R-34
CHECK VALVE - DESCRIPTION, VACUUM . . 24-28
CHECK VALVE - INSTALLATION, FRONT....8R-9
CHECK VALVE - INSTALLATION, FUEL
TANK ..............................14-28
CHECK VALVE - INSTALLATION, REAR....8R-35
CHECK VALVE - INSTALLATION, VACUUM . 24-28
CHECK VALVE - OPERATION, FRONT......8R-9
CHECK VALVE - OPERATION, FUEL TANK . . 14-28
CHECK VALVE - OPERATION, REAR......8R-34
CHECK VALVE - OPERATION, VACUUM....24-28
CHECK VALVE - REMOVAL, FRONT.......8R-9
CHECK VALVE - REMOVAL, FUEL TANK . . . 14-28
CHECK VALVE - REMOVAL, REAR.......8R-34
CHECK VALVE - REMOVAL, VACUUM.....24-28
CHECKING TRANSMISSION CLUTCH
OPERATION - DIAGNOSIS AND
TESTING, AIR.......................21-80
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-3
CHILD TETHER ANCHOR - DESCRIPTION . . 8O-13
CHILD TETHER ANCHOR - OPERATION . . . 8O-13
CHIME WARNING SYSTEM -
DESCRIPTION........................8B-1
CHIME WARNING SYSTEM - DIAGNOSIS
AND TESTING........................8B-6
CHIME WARNING SYSTEM - OPERATION . . . 8B-2
CHOKE AND RELAY - DESCRIPTION,
AMPLIFIER..........................8A-3
CHOKE AND RELAY - DIAGNOSIS AND
TESTING, AMPLIFIER..................8A-4
CHOKE AND RELAY - INSTALLATION,
AMPLIFIER..........................8A-4
CHOKE AND RELAY - OPERATION,
AMPLIFIER..........................8A-3
CHOKE AND RELAY - REMOVAL,
AMPLIFIER..........................8A-4
CIGAR LIGHTER OUTLET -
DESCRIPTION.....................8W-97-2
CIGAR LIGHTER OUTLET - DIAGNOSIS
AND TESTING.....................8W-97-2
CIGAR LIGHTER OUTLET - OPERATION . 8W-97-2
CLEVIS BRACKET - INSTALLATION........2-13
CLEVIS BRACKET - REMOVAL...........2-13
CLOCKSPRING - DESCRIPTION.........8O-13
CLOCKSPRING - INSTALLATION.........8O-16
CLOCKSPRING - OPERATION...........8O-14
CLOCKSPRING - REMOVAL............8O-15
CLOCKSPRING CENTERING - STANDARD
PROCEDURE........................8O-14
CLUSTER - ASSEMBLY, INSTRUMENT....8J-10
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-2
CLUSTER - DIAGNOSIS AND TESTING,
INSTRUMENT........................8J-7
CLUSTER - DISASSEMBLY, INSTRUMENT . . . 8J-9
CLUSTER - INSTALLATION, INSTRUMENT . 8J-11
CLUSTER - OPERATION, INSTRUMENT.....8J-4
CLUSTER - REMOVAL, INSTRUMENT......8J-9
CLUSTER BEZEL - INSTALLATION.......23-147
CLUSTER BEZEL - REMOVAL..........23-147
CLUTCH - ASSEMBLY, LOW/REVERSE
. . . 21-146
CLUTCH - CLEANING, LOW/REVERSE
....21-146
CLUTCH - DESCRIPTION
.................6-1
CLUTCH - DIAGNOSIS AND TESTING
.......6-2
CLUTCH - DISASSEMBLY, LOW/REVERSE
. 21-145
CLUTCH - INSPECTION, A/C
COMPRESSOR
.......................24-14
CLUTCH - INSPECTION, LOW/REVERSE
. . 21-146
CLUTCH - INSTALLATION, A/C
COMPRESSOR
.......................24-14
CLUTCH - OPERATION
..................6-1
CLUTCH - REMOVAL, A/C COMPRESSOR
. . 24-13
CLUTCH - SPECIFICATIONS
...............6-5
CLUTCH - WARNING
....................6-2
CLUTCH ASSEMBLY - ASSEMBLY, INPUT
. 21-138CLUTCH ASSEMBLY - DESCRIPTION,
INPUT............................21-133
CLUTCH ASSEMBLY - DISASSEMBLY,
INPUT............................21-135
CLUTCH ASSEMBLY - OPERATION,
INPUT............................21-135
CLUTCH BREAK-IN - STANDARD
PROCEDURE, A/C COMPRESSOR........24-12
CLUTCH COIL - DIAGNOSIS AND
TESTING, A/C COMPRESSOR...........24-12
CLUTCH DISC - INSTALLATION............6-6
CLUTCH DISC - REMOVAL...............6-6
CLUTCH OPERATION - DIAGNOSIS AND
TESTING, AIR CHECKING
TRANSMISSION......................21-80
CLUTCH PEDAL - INSTALLATION.........6-10
CLUTCH PEDAL - REMOVAL.............6-10
CLUTCH PEDAL POSITION SWITCH -
DESCRIPTION........................6-11
CLUTCH PEDAL POSITION SWITCH -
DIAGNOSIS AND TESTING..............6-11
CLUTCH PEDAL POSITION SWITCH -
OPERATION..........................6-11
CLUTCH RELAY - DESCRIPTION, A/C
COMPRESSOR.......................24-15
CLUTCH RELAY - DIAGNOSIS AND
TESTING, COMPRESSOR...............24-15
CLUTCH RELAY - INSTALLATION, A/C
COMPRESSOR.......................24-16
CLUTCH RELAY - OPERATION, A/C
COMPRESSOR.......................24-15
CLUTCH RELAY - REMOVAL, A/C
COMPRESSOR........................24-16
CLUTCH RELEASE BEARING -
INSTALLATION.........................6-6
CLUTCH RELEASE BEARING - REMOVAL....6-6
CLUTCH SWITCH OVERRIDE RELAY -
DESCRIPTION........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
INSTALLATION........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
OPERATION..........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
REMOVAL...........................6-10
CLUTCHES - DESCRIPTION, HOLDING . . . 21-131
CLUTCHES - OPERATION, HOLDING.....21-132
CMTC LAMP REPLACEMENT -
STANDARD PROCEDURE...............8M-2
COAT FINISH - DESCRIPTION, BASE
COAT/CLEAR.......................23-162
COAT/CLEAR COAT FINISH -
DESCRIPTION, BASE.................23-162
CODE - DESCRIPTION, PAINT..........23-162
CODES - DESCRIPTION, DIAGNOSTIC
TROUBLE............................25-2
CODES - SPECIFICATIONS, PAINT.......23-162
CODES - STANDARD PROCEDURE,
ERASING TRANSMITTER...............8M-8
CODES - STANDARD PROCEDURE,
SETTING TRANSMITTER...............8M-9
COIL - DESCRIPTION, IGNITION..........8I-9
COIL - DIAGNOSIS AND TESTING, A/C
COMPRESSOR CLUTCH...............24-12
COIL - INSTALLATION, IGNITION.........8I-10
COIL - OPERATION, IGNITION............8I-9
COIL - REMOVAL, IGNITION............8I-10
COIL CAPACITOR - DESCRIPTION,
IGNITION...........................8I-16
COIL CAPACITOR - INSTALLATION,
IGNITION...........................8I-16
COIL CAPACITOR - OPERATION,
IGNITION...........................8I-16
COIL CAPACITOR - REMOVAL, IGNITION . . . 8I-16
COIL RESISTANCE, 2.4L - IGNITION
.......8I-2
COIL RESISTANCE, 3.7L V-6 - IGNITION
....8I-3
COLLAPSIBLE SPACER - INSTALLATION
....3-70
COLLAPSIBLE SPACER - REMOVAL
.......3-70
COLUMN - DESCRIPTION
...............19-5
COLUMN - INSTALLATION
...............19-7
COLUMN - REMOVAL
..................19-5
COLUMN, SPECIAL TOOLS - STEERING
....19-8
COMBINATION FLASHER - DESCRIPTION
. . 8L-19
COMBINATION FLASHER - OPERATION
. . . 8L-19
COMBUSTION PRESSURE LEAKAGE -
DIAGNOSIS AND TESTING, CYLINDER
......9-8
COMMUNICATION - DESCRIPTION
........8E-8
COMMUNICATION - OPERATION
..........8E-8
KJINDEX 5
Description Group-Page Description Group-Page Description Group-Page

Page 1770 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual ADJUSTER (TAPPET) NOISE DIAGNOSIS
- DIAGNOSIS AND TESTING, LASH........9-28
ADJUSTMENT, FRONT FOG LAMP UNIT . . . 8L-25
ADJUSTMENT, HEADLAMP UNIT.........8L-42
AIMING - STANDARD PROCEDURE,
LAMP BAR...

ADJUSTER (TAPPET) NOISE DIAGNOSIS
- DIAGNOSIS AND TESTING, LASH........9-28
ADJUSTMENT, FRONT FOG LAMP UNIT . . . 8L-25
ADJUSTMENT, HEADLAMP UNIT.........8L-42
AIMING - STANDARD PROCEDURE,
LAMP BAR..........................8L-65
ARM BUSHING - INSTALLATION, LOWER
CONTROL............................2-3
ARM BUSHING - INSTALLATION, LOWER
SUSPENSION..........................2-8
ARM BUSHING - INSTALLATION, UPPER
SUSPENSION..........................2-8
ARM BUSHING - REMOVAL, LOWER
CONTROL............................2-2
ARM BUSHING - REMOVAL, LOWER
SUSPENSION..........................2-7
ARM BUSHING - REMOVAL, UPPER
SUSPENSION..........................2-7
ARM BUSHINGS - INSTALLATION,
UPPER CONTROL......................2-4
ARM BUSHINGS - REMOVAL, UPPER
CONTROL............................2-3
ARMS - INSPECTION, ROCKER...........9-30
ARMS - INSTALLATION, ROCKER.........9-30
ARMS - REMOVAL, ROCKER.............9-29
ASSEMBLY - INSTALLATION, ENGINE......9-12
ASSEMBLY - REMOVAL, ENGINE.........9-12
ASSEMBLY, OIL PUMP.................9-50
BACKUP LAMP SWITCH - DESCRIPTION . . 8L-15
BACKUP LAMP SWITCH - DIAGNOSIS
AND TESTING.........................8L-15
BACKUP LAMP SWITCH - OPERATION....8L-15
BALANCE SHAFT - DESCRIPTION.........9-59
BALANCE SHAFT - OPERATION...........9-59
BALANCE SHAFT - REMOVAL............9-60
BALANCE SHAFT CARRIER -
INSTALLATION........................9-64
BALANCE SHAFT CARRIER - REMOVAL....9-64
BALANCE SHAFT CHAIN - INSTALLATION . . . 9-64
BALANCE SHAFT CHAIN - REMOVAL......9-64
BALANCE SHAFT TIMING, INSTALLATION . . . 9-61
BALL JOINT - INSTALLATION, LOWER......2-5
BALL JOINT - INSTALLATION, UPPER......2-6
BALL JOINT - REMOVAL, LOWER..........2-5
BALL JOINT - REMOVAL, UPPER..........2-6
BAR - DESCRIPTION, LAMP............8L-65
BAR - DIAGNOSIS AND TESTING, LAMP . . 8L-65
BAR - INSTALLATION, LAMP............8L-66
BAR - OPERATION, LAMP..............8L-65
BAR - REMOVAL, LAMP...............8L-65
BAR AIMING - STANDARD PROCEDURE,
LAMP..............................8L-65
BAR SWITCH - DESCRIPTION, LAMP.....8L-67
BAR SWITCH - INSTALLATION, LAMP....8L-67
BAR SWITCH - REMOVAL, LAMP........8L-67
BEAM RELAY - DESCRIPTION,
HEADLAMP HIGH....................8L-33
BEAM RELAY - DESCRIPTION,
HEADLAMP LOW.....................8L-39
BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP HIGH............8L-34
BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP LOW.............8L-40
BEAM RELAY - INSTALLATION,
HEADLAMP HIGH
....................8L-35
BEAM RELAY - INSTALLATION,
HEADLAMP LOW
.....................8L-41
BEAM RELAY - OPERATION, HEADLAMP
HIGH
..............................8L-33
BEAM RELAY - OPERATION, HEADLAMP
LOW
..............................8L-39
BEAM RELAY - REMOVAL, HEADLAMP
HIGH
..............................8L-34
BEAM RELAY - REMOVAL, HEADLAMP
LOW
..............................8L-40
BEARING - FITTING - STANDARD
PROCEDURE, MAIN
....................9-35
BEARING CLEARANCE USING
PLASTIGAGE - STANDARD
PROCEDURE, MEASURING
..............9-11
BELT - INSTALLATION, TIMING
...........9-56
BELT - REMOVAL, TIMING
..............9-55
BELT COVER(S) - INSTALLATION,
TIMING
.............................9-53
BELT COVER(S) - REMOVAL, TIMING
......9-53
BELT DIAGNOSIS - DIAGNOSIS AND
TESTING, SERPENTINE DRIVE
...........7-15BELT TENSIONER & PULLEY -
INSTALLATION, TIMING.................9-59
BELT TENSIONER & PULLEY -
REMOVAL, TIMING....................9-59
BLOCK - DESCRIPTION, ENGINE..........9-30
BLOCK HEATER - 2.4L - DESCRIPTION,
ENGINE.............................7-20
BLOCK HEATER - 2.4L - OPERATION,
ENGINE.............................7-20
BORE FITTING - STANDARD
PROCEDURE, PISTON TO CYLINDER......9-30
BORE HONING - STANDARD
PROCEDURE, CYLINDER................9-31
BRACKET BUSHING - INSTALLATION,
CLEVIS..............................2-4
BRACKET BUSHING - REMOVAL, CLEVIS....2-2
BRAKE LAMP SWITCH - DESCRIPTION . . . 8L-16
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-17
BRAKE LAMP SWITCH - INSTALLATION . . . 8L-18
BRAKE LAMP SWITCH - OPERATION.....8L-16
BRAKE LAMP SWITCH - REMOVAL......8L-17
BULB - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP................8L-19
BULB - INSTALLATION, FRONT FOG
LAMP..............................8L-22
BULB - INSTALLATION, FRONT LAMP....8L-27
BULB - INSTALLATION, FRONT POSITION
LAMP..............................8L-28
BULB - INSTALLATION, HEADLAMP......8L-32
BULB - INSTALLATION, LICENSE PLATE
LAMP..............................8L-45
BULB - INSTALLATION, REAR LAMP.....8L-59
BULB - INSTALLATION, REPEATER LAMP . . 8L-60
BULB - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP................8L-18
BULB - REMOVAL, FRONT FOG LAMP....8L-21
BULB - REMOVAL, FRONT LAMP........8L-27
BULB - REMOVAL, FRONT POSITION
LAMP..............................8L-28
BULB - REMOVAL, HEADLAMP..........8L-30
BULB - REMOVAL, LICENSE PLATE
LAMP..............................8L-44
BULB - REMOVAL, REAR LAMP.........8L-59
BULB - REMOVAL, REPEATER LAMP.....8L-60
BUSHING - INSTALLATION, CLEVIS
BRACKET.............................2-4
BUSHING - INSTALLATION, LOWER
CONTROL ARM........................2-3
BUSHING - INSTALLATION, LOWER
SUSPENSION ARM.....................2-8
BUSHING - INSTALLATION, UPPER
SUSPENSION ARM.....................2-8
BUSHING - REMOVAL, CLEVIS BRACKET....2-2
BUSHING - REMOVAL, LOWER CONTROL
ARM ................................2-2
BUSHING - REMOVAL, LOWER
SUSPENSION ARM.....................2-7
BUSHING - REMOVAL, UPPER
SUSPENSION ARM.....................2-7
BUSHINGS - INSTALLATION, UPPER
CONTROL ARM........................2-4
BUSHINGS - REMOVAL, UPPER
CONTROL ARM........................2-3
CAMSHAFT END-PLAY - STANDARD
PROCEDURE.........................9-23
CAMSHAFT OIL SEAL(S) - INSTALLATION . . 9-22
CAMSHAFT OIL SEAL(S) - REMOVAL......9-22
CAMSHAFT(S) - CLEANING..............9-24
CAMSHAFT(S) - DESCRIPTION...........9-23
CAMSHAFT(S) - INSPECTION............9-25
CAMSHAFT(S) - INSTALLATION..........9-25
CAMSHAFT(S) - OPERATION.............9-23
CAMSHAFT(S) - REMOVAL..............9-24
CAP - CLEANING, RADIATOR PRESSURE . . . 7-25
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-25
CAP - DIAGNOSIS AND TESTING,
RADIATOR PRESSURE.................7-25
CAP - INSPECTION, RADIATOR
PRESSURE..........................7-25
CAP - OPERATION, RADIATOR
PRESSURE
..........................7-25
CARRIER - INSTALLATION, BALANCE
SHAFT
..............................9-64
CARRIER - REMOVAL, BALANCE SHAFT
....9-64
CATALYTIC CONVERTER - DESCRIPTION
. . . 11-2
CATALYTIC CONVERTER - INSPECTION
....11-3CATALYTIC CONVERTER - INSTALLATION . . . 11-3
CATALYTIC CONVERTER - REMOVAL......11-2
CENTER HIGH MOUNTED STOP LAMP
BULB - INSTALLATION................8L-19
CENTER HIGH MOUNTED STOP LAMP
BULB - REMOVAL....................8L-18
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION.................8L-19
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL....................8L-19
CHAIN - INSTALLATION, BALANCE
SHAFT..............................9-64
CHAIN - REMOVAL, BALANCE SHAFT......9-64
CHANGE - STANDARD PROCEDURE,
ENGINE OIL AND FILTER................9-47
CHART - DIAGNOSIS AND TESTING,
COOLING SYSTEM DIAGNOSIS............7-5
CHECK, STANDARD PROCEDURE -
ENGINE OIL LEVEL....................9-47
CHECKING - DIAGNOSIS AND TESTING,
ENGINE OIL PRESSURE................9-46
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-2
CLAMPS - DESCRIPTION, HOSE...........7-1
CLAMPS - OPERATION, HOSE.............7-2
CLEANING, CAMSHAFT(S)...............9-24
CLEANING, CYLINDER HEAD.............9-20
CLEANING, CYLINDER HEAD COVER......9-26
CLEANING, EXHAUST MANIFOLD.........9-53
CLEANING, INTAKE/EXHAUST VALVES &
SEATS................................9-27
CLEANING, OIL PUMP..................9-49
CLEANING, RADIATOR.................7-24
CLEANING, RADIATOR PRESSURE CAP....7-25
CLEANING, REMOVAL..................9-55
CLEANING, STANDARD PROCEDURE......9-31
CLEARANCE USING PLASTIGAGE -
STANDARD PROCEDURE, MEASURING
BEARING............................9-11
CLEVIS BRACKET BUSHING -
INSTALLATION.........................2-4
CLEVIS BRACKET BUSHING - REMOVAL....2-2
COLLAR - INSTALLATION, STRUCTURAL . . . 9-44
COLLAR - REMOVAL, STRUCTURAL.......9-44
COMBINATION FLASHER - DESCRIPTION . . 8L-19
COMBINATION FLASHER - OPERATION . . . 8L-19
COMBUSTION PRESSURE LEAKAGE
TEST - DIAGNOSIS AND TESTING,
CYLINDER............................9-3
COMPRESSION PRESSURE TEST -
DIAGNOSIS AND TESTING, CYLINDER......9-3
CONNECTING ROD - DESCRIPTION,
PISTON.............................9-40
CONNECTING ROD - INSTALLATION,
PISTON.............................9-41
CONNECTING ROD - OPERATION,
PISTON.............................9-40
CONNECTING ROD - REMOVAL, PISTON . . . 9-40
CONNECTING ROD, FITTING.............9-32
CONNECTOR - INSTALLATION, TRAILER
TOW ..............................8L-61
CONNECTOR - REMOVAL, TRAILER TOW . . 8L-61
CONTAINER - DESCRIPTION, COOLANT
RECOVERY PRESS....................7-20
CONTAINER - OPERATION, COOLANT
RECOVERY PRESS....................7-20
CONTROL ARM BUSHING -
INSTALLATION, LOWER.................2-3
CONTROL ARM BUSHING - REMOVAL,
LOWER..............................2-2
CONTROL ARM BUSHINGS -
INSTALLATION, UPPER..................2-4
CONTROL ARM BUSHINGS - REMOVAL,
UPPER...............................2-3
CONVERTER - DESCRIPTION, CATALYTIC . . . 11-2
CONVERTER - INSPECTION, CATALYTIC....11-3
CONVERTER - INSTALLATION, CATALYTIC . . 11-3
CONVERTER - REMOVAL, CATALYTIC......11-2
COOLANT - DESCRIPTION, ENGINE.......7-19
COOLANT - DESCRIPTION, HOAT
.........7-18
COOLANT RECOVERY PRESS
CONTAINER - DESCRIPTION
.............7-20
COOLANT RECOVERY PRESS
CONTAINER - OPERATION
...............7-20
COOLANT TEMPERATURE SENSOR -
DESCRIPTION, ENGINE
.................7-21
COOLANT TEMPERATURE SENSOR -
INSTALLATION, ENGINE
................7-22
KJINDEX 1
Description Group-Page Description Group-Page Description Group-Page

Page 1772 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual ENGINE CORE AND OIL GALLERY PLUGS
- STANDARD PROCEDURE...............9-9
ENGINE DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING...............9-5
ENGINE GASKET SURFACE
PREPARATION - STANDARD
PROCEDURE

ENGINE CORE AND OIL GALLERY PLUGS
- STANDARD PROCEDURE...............9-9
ENGINE DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING...............9-5
ENGINE GASKET SURFACE
PREPARATION - STANDARD
PROCEDURE.........................9-11
ENGINE MECHANICAL - DIAGNOSIS AND
TESTING.............................9-7
ENGINE MOUNTING - DESCRIPTION......9-44
ENGINE OIL AND FILTER CHANGE -
STANDARD PROCEDURE................9-47
ENGINE OIL LEAK INSPECTION -
DIAGNOSIS AND TESTING...............9-4
ENGINE OIL LEVEL CHECK, STANDARD
PROCEDURE.........................9-47
ENGINE OIL PRESSURE CHECKING -
DIAGNOSIS AND TESTING..............9-46
ENGINE, SPECIAL TOOLS - 2.4L..........9-17
EXHAUST MANIFOLD - CLEANING........9-53
EXHAUST MANIFOLD - DESCRIPTION.....9-53
EXHAUST MANIFOLD - INSPECTION.......9-53
EXHAUST MANIFOLD - INSTALLATION.....9-53
EXHAUST MANIFOLD - OPERATION.......9-53
EXHAUST MANIFOLD - REMOVAL.........9-53
EXHAUST SYSTEM - DESCRIPTION.......11-1
EXHAUST SYSTEM - DIAGNOSIS AND
TESTING............................11-2
EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - DIAGNOSIS AND TESTING,
LAMPS/LIGHTING.....................8L-7
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-5
EXTERIOR - SPECIFICATIONS,
LAMPS/LIGHTING....................8L-15
FAN - ELECTRIC - DESCRIPTION,
RADIATOR...........................7-26
FAN - ELECTRIC - INSTALLATION,
RADIATOR...........................7-27
FAN - ELECTRIC - OPERATION,
RADIATOR...........................7-26
FAN - ELECTRIC - REMOVAL, RADIATOR . . . 7-26
FILTER - DESCRIPTION, OIL.............9-47
FILTER - INSTALLATION, OIL............9-47
FILTER - REMOVAL, OIL................9-47
FILTER CHANGE - STANDARD
PROCEDURE, ENGINE OIL...............9-47
FITTING - CONNECTING ROD............9-32
FITTING - PISTON RING................9-42
FITTING - STANDARD PROCEDURE,
MAIN BEARING.......................9-35
FITTING - STANDARD PROCEDURE,
PISTON TO CYLINDER BORE............9-30
FLASHER - DESCRIPTION, COMBINATION . 8L-19
FLASHER - OPERATION, COMBINATION . . . 8L-19
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM - REVERSE...........7-12
FLUSHING COOLERS AND TUBES -
STANDARD PROCEDURE................7-30
FOG LAMP BULB - INSTALLATION,
FRONT.............................8L-22
FOG LAMP BULB - REMOVAL, FRONT....8L-21
FOG LAMP RELAY - DESCRIPTION,
FRONT.............................8L-22
FOG LAMP RELAY - DESCRIPTION, REAR . 8L-56
FOG LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT.....................8L-23
FOG LAMP RELAY - DIAGNOSIS AND
TESTING, REAR......................8L-57
FOG LAMP RELAY - INSTALLATION,
FRONT.............................8L-24
FOG LAMP RELAY - INSTALLATION,
REAR..............................8L-58
FOG LAMP RELAY - OPERATION, FRONT . . 8L-22
FOG LAMP RELAY - OPERATION, REAR . . . 8L-57
FOG LAMP RELAY - REMOVAL, FRONT . . . 8L-24
FOG LAMP RELAY - REMOVAL, REAR....8L-58
FOG LAMP UNIT - ADJUSTMENT, FRONT . . 8L-25
FOG LAMP UNIT - INSTALLATION,
FRONT
.............................8L-25
FOG LAMP UNIT - REMOVAL, FRONT
.....8L-24
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE
......9-10
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL
............................9-37
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL
...............................9-37FRONT FOG LAMP BULB -
INSTALLATION.......................8L-22
FRONT FOG LAMP BULB - REMOVAL.....8L-21
FRONT FOG LAMP RELAY -
DESCRIPTION.......................8L-22
FRONT FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-23
FRONT FOG LAMP RELAY -
INSTALLATION.......................8L-24
FRONT FOG LAMP RELAY - OPERATION . . 8L-22
FRONT FOG LAMP RELAY - REMOVAL....8L-24
FRONT FOG LAMP UNIT - ADJUSTMENT . . 8L-25
FRONT FOG LAMP UNIT - INSTALLATION . . 8L-25
FRONT FOG LAMP UNIT - REMOVAL.....8L-24
FRONT LAMP BULB - INSTALLATION.....8L-27
FRONT LAMP BULB - REMOVAL.........8L-27
FRONT LAMP UNIT - INSTALLATION.....8L-28
FRONT LAMP UNIT - REMOVAL.........8L-27
FRONT MOUNT - INSTALLATION..........9-44
FRONT MOUNT - REMOVAL.............9-44
FRONT POSITION LAMP BULB -
INSTALLATION.......................8L-28
FRONT POSITION LAMP BULB -
REMOVAL..........................8L-28
FRONT SUSPENSION, SPECIAL TOOLS.....2-1
GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE AND OIL......9-9
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD......................9-19
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE........9-11
GASKETS AND SEALERS - STANDARD
PROCEDURE, FORM-IN-PLACE...........9-10
HAZARD SWITCH - DESCRIPTION.......8L-28
HAZARD SWITCH - INSTALLATION.......8L-30
HAZARD SWITCH - OPERATION.........8L-29
HAZARD SWITCH - REMOVAL..........8L-29
HEAD - CLEANING, CYLINDER...........9-20
HEAD - DESCRIPTION, CYLINDER........9-19
HEAD - INSPECTION, CYLINDER..........9-21
HEAD - INSTALLATION, CYLINDER........9-21
HEAD - OPERATION, CYLINDER..........9-19
HEAD - REMOVAL, CYLINDER...........9-20
HEAD COVER - CLEANING, CYLINDER.....9-26
HEAD COVER - INSPECTION, CYLINDER . . . 9-26
HEAD COVER - INSTALLATION,
CYLINDER...........................9-26
HEAD COVER - REMOVAL, CYLINDER.....9-26
HEAD GASKET - DIAGNOSIS AND
TESTING, CYLINDER...................9-19
HEAD OFF - INSTALLATION, CYLINDER....9-28
HEAD OFF - REMOVAL, CYLINDER........9-27
HEAD ON - INSTALLATION, CYLINDER.....9-28
HEAD ON - REMOVAL, CYLINDER........9-27
HEADLAMP BULB - INSTALLATION.......8L-32
HEADLAMP BULB - REMOVAL..........8L-30
HEADLAMP HIGH BEAM RELAY -
DESCRIPTION.......................8L-33
HEADLAMP HIGH BEAM RELAY -
DIAGNOSIS AND TESTING.............8L-34
HEADLAMP HIGH BEAM RELAY -
INSTALLATION.......................8L-35
HEADLAMP HIGH BEAM RELAY -
OPERATION.........................8L-33
HEADLAMP HIGH BEAM RELAY -
REMOVAL..........................8L-34
HEADLAMP LEVELING MOTOR -
DESCRIPTION.......................8L-35
HEADLAMP LEVELING MOTOR -
INSTALLATION.......................8L-36
HEADLAMP LEVELING MOTOR -
OPERATION.........................8L-36
HEADLAMP LEVELING MOTOR -
REMOVAL..........................8L-36
HEADLAMP LEVELING SWITCH -
DESCRIPTION.......................8L-37
HEADLAMP LEVELING SWITCH -
DIAGNOSIS AND TESTING.............8L-37
HEADLAMP LEVELING SWITCH -
INSTALLATION
.......................8L-38
HEADLAMP LEVELING SWITCH -
OPERATION
.........................8L-37
HEADLAMP LEVELING SWITCH -
REMOVAL
..........................8L-38
HEADLAMP LOW BEAM RELAY -
DESCRIPTION
.......................8L-39
HEADLAMP LOW BEAM RELAY -
DIAGNOSIS AND TESTING
.............8L-40HEADLAMP LOW BEAM RELAY -
INSTALLATION.......................8L-41
HEADLAMP LOW BEAM RELAY -
OPERATION.........................8L-39
HEADLAMP LOW BEAM RELAY -
REMOVAL..........................8L-40
HEADLAMP UNIT - ADJUSTMENT........8L-42
HEADLAMP UNIT - INSTALLATION.......8L-42
HEADLAMP UNIT - REMOVAL...........8L-41
HEAT SHIELDS - DESCRIPTION..........11-4
HEATER - 2.4L - DESCRIPTION, ENGINE
BLOCK..............................7-20
HEATER - 2.4L - OPERATION, ENGINE
BLOCK..............................7-20
HIGH BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-33
HIGH BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-34
HIGH BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-35
HIGH BEAM RELAY - OPERATION,
HEADLAMP.........................8L-33
HIGH BEAM RELAY - REMOVAL,
HEADLAMP.........................8L-34
HIGH MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER...............8L-19
HIGH MOUNTED STOP LAMP BULB -
REMOVAL, CENTER...................8L-18
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER...............8L-19
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER...................8L-19
HOAT COOLANT - DESCRIPTION..........7-18
HONING - STANDARD PROCEDURE,
CYLINDER BORE......................9-31
HOSE CLAMPS - DESCRIPTION...........7-1
HOSE CLAMPS - OPERATION.............7-2
HYDRAULIC LIFTERS - INSTALLATION.....9-29
HYDRAULIC LIFTERS - REMOVAL.........9-29
HYDROSTATIC LOCKED ENGINE -
STANDARD PROCEDURE.................9-9
INSPECTION - DIAGNOSIS AND
TESTING, ENGINE OIL LEAK..............9-4
INSPECTION, CAMSHAFT(S).............9-25
INSPECTION, CATALYTIC CONVERTER.....11-3
INSPECTION, CRANKSHAFT.............9-34
INSPECTION, CYLINDER HEAD...........9-21
INSPECTION, CYLINDER HEAD COVER.....9-26
INSPECTION, EXHAUST MANIFOLD.......9-53
INSPECTION, INTAKE MANIFOLD.........9-52
INSPECTION, OIL PUMP................9-50
INSPECTION, RADIATOR................7-24
INSPECTION, RADIATOR PRESSURE CAP . . . 7-25
INSPECTION, REMOVAL................9-28
INSPECTION, ROCKER ARMS............9-30
INSPECTION, STANDARD PROCEDURE.....9-32
INSPECTION, WATER PUMP - 2.4L........7-28
INSTALLATION - BALANCE SHAFT
TIMING.............................9-61
INSTALLATION, 2.4L...................7-20
INSTALLATION, 2.4L...................9-19
INSTALLATION, 2.4L ENGINE....7-14,7-17,7-22,
7-28
INSTALLATION, BALANCE SHAFT
CARRIER............................9-64
INSTALLATION, BALANCE SHAFT CHAIN . . . 9-64
INSTALLATION, BRAKE LAMP SWITCH....8L-18
INSTALLATION, CAMSHAFT OIL SEAL(S) . . . 9-22
INSTALLATION, CAMSHAFT(S)...........9-25
INSTALLATION, CATALYTIC CONVERTER
....11-3
INSTALLATION, CENTER HIGH MOUNTED
STOP LAMP BULB
....................8L-19
INSTALLATION, CENTER HIGH MOUNTED
STOP LAMP UNIT
....................8L-19
INSTALLATION, CLEVIS BRACKET
BUSHING
.............................2-4
INSTALLATION, CRANKSHAFT
............9-34
INSTALLATION, CRANKSHAFT OIL SEAL -
FRONT
..............................9-37
INSTALLATION, CRANKSHAFT OIL SEAL -
REAR
...............................9-39
INSTALLATION, CRANKSHAFT SPROCKET
. . 9-56
INSTALLATION, CROSS-OVER PIPE
.......11-4
INSTALLATION, CYLINDER HEAD
.........9-21
INSTALLATION, CYLINDER HEAD COVER
. . . 9-26
INSTALLATION, CYLINDER HEAD OFF
......9-28
INSTALLATION, CYLINDER HEAD ON
......9-28
KJINDEX 3
Description Group-Page Description Group-Page Description Group-Page

Page 1774 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual MANIFOLD LEAKS - DIAGNOSIS AND
TESTING, INTAKE.....................9-51
MEASURING BEARING CLEARANCE
USING PLASTIGAGE - STANDARD
PROCEDURE.........................9-11
MECHANICAL - DIAGNOSIS AND
TESTIN

MANIFOLD LEAKS - DIAGNOSIS AND
TESTING, INTAKE.....................9-51
MEASURING BEARING CLEARANCE
USING PLASTIGAGE - STANDARD
PROCEDURE.........................9-11
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE......................9-7
MOTOR - DESCRIPTION, HEADLAMP
LEVELING..........................8L-35
MOTOR - INSTALLATION, HEADLAMP
LEVELING..........................8L-36
MOTOR - OPERATION, HEADLAMP
LEVELING..........................8L-36
MOTOR - REMOVAL, HEADLAMP
LEVELING..........................8L-36
MOUNT - INSTALLATION, FRONT.........9-44
MOUNT - INSTALLATION, REAR..........9-45
MOUNT - REMOVAL, FRONT.............9-44
MOUNT - REMOVAL, REAR..............9-45
MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP BULB -
REMOVAL, CENTER HIGH..............8L-18
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH..............8L-19
MOUNTING - DESCRIPTION, ENGINE......9-44
MUFFLER - DESCRIPTION...............11-4
MUFFLER - INSTALLATION..............11-5
MUFFLER - REMOVAL..................11-4
MULTI-FUNCTION SWITCH -
DESCRIPTION.......................8L-46
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-50
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-53
MULTI-FUNCTION SWITCH - OPERATION . . 8L-48
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-53
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, LASH ADJUSTER (TAPPET)......9-28
OFF - INSTALLATION, CYLINDER HEAD....9-28
OFF - REMOVAL, CYLINDER HEAD........9-27
OIL AND FILTER CHANGE - STANDARD
PROCEDURE, ENGINE..................9-47
OIL FILTER - DESCRIPTION.............9-47
OIL FILTER - INSTALLATION.............9-47
OIL FILTER - REMOVAL.................9-47
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE..............9-9
OIL LEAK INSPECTION - DIAGNOSIS
AND TESTING, ENGINE..................9-4
OIL LEVEL CHECK, STANDARD
PROCEDURE - ENGINE.................9-47
OIL PAN - INSTALLATION...............9-48
OIL PAN - REMOVAL...................9-48
OIL PRESSURE CHECKING - DIAGNOSIS
AND TESTING, ENGINE.................9-46
OIL PRESSURE SENSOR/SWITCH -
DESCRIPTION........................9-48
OIL PRESSURE SENSOR/SWITCH -
OPERATION..........................9-48
OIL PUMP - ASSEMBLY................9-50
OIL PUMP - CLEANING.................9-49
OIL PUMP - DISASSEMBLY.............9-49
OIL PUMP - INSPECTION...............9-50
OIL PUMP - INSTALLATION.............9-50
OIL PUMP - REMOVAL.................9-49
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT........................9-37
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT........................9-37
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT........................9-39
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT........................9-38
OIL SEAL(S) - INSTALLATION,
CAMSHAFT..........................9-22
OIL SEAL(S) - REMOVAL, CAMSHAFT.....9-22
ON-BOARD DIAGNOSTICS (OBD) -
DIAGNOSIS AND TESTING...............7-2
OPERATION, BACKUP LAMP SWITCH.....8L-15
OPERATION, BALANCE SHAFT
...........9-59
OPERATION, BRAKE LAMP SWITCH
......8L-16
OPERATION, CAMSHAFT(S)
.............9-23
OPERATION, COMBINATION FLASHER
....8L-19
OPERATION, COOLANT RECOVERY
PRESS CONTAINER
....................7-20OPERATION, COOLING SYSTEM...........7-2
OPERATION, CRANKSHAFT..............9-33
OPERATION, CYLINDER HEAD...........9-19
OPERATION, DAYTIME RUNNING LAMP
RELAY.............................8L-20
OPERATION, DESCRIPTION..............7-20
OPERATION, ENGINE BLOCK HEATER -
2.4L................................7-20
OPERATION, ENGINE COOLANT
TEMPERATURE SENSOR................7-21
OPERATION, EXHAUST MANIFOLD........9-53
OPERATION, FRONT FOG LAMP RELAY . . . 8L-22
OPERATION, HAZARD SWITCH..........8L-29
OPERATION, HEADLAMP HIGH BEAM
RELAY.............................8L-33
OPERATION, HEADLAMP LEVELING
MOTOR............................8L-36
OPERATION, HEADLAMP LEVELING
SWITCH............................8L-37
OPERATION, HEADLAMP LOW BEAM
RELAY.............................8L-39
OPERATION, HOSE CLAMPS..............7-2
OPERATION, INTAKE MANIFOLD..........9-51
OPERATION, LAMP BAR...............8L-65
OPERATION, LAMPS/LIGHTING -
EXTERIOR...........................8L-5
OPERATION, LUBRICATION..............9-46
OPERATION, MULTI-FUNCTION SWITCH . . . 8L-48
OPERATION, OIL PRESSURE SENSOR/
SWITCH..............................9-48
OPERATION, PARK LAMP RELAY........8L-54
OPERATION, PISTON & CONNECTING
ROD................................9-40
OPERATION, RADIATOR FAN - ELECTRIC . . . 7-26
OPERATION, RADIATOR PRESSURE CAP . . . 7-25
OPERATION, REAR FOG LAMP RELAY....8L-57
OPERATION, TRAILER TOW RELAY.......8L-62
OPERATION, WATER PUMP - 2.4L........7-27
PAN - INSTALLATION, OIL...............9-48
PAN - REMOVAL, OIL..................9-48
PARK LAMP RELAY - DESCRIPTION......8L-54
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-55
PARK LAMP RELAY - INSTALLATION.....8L-56
PARK LAMP RELAY - OPERATION.......8L-54
PARK LAMP RELAY - REMOVAL.........8L-55
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-5
PIPE - INSTALLATION, CROSS-OVER......11-4
PIPE - REMOVAL, CROSS-OVER..........11-4
PISTON & CONNECTING ROD -
DESCRIPTION........................9-40
PISTON & CONNECTING ROD -
INSTALLATION........................9-41
PISTON & CONNECTING ROD -
OPERATION..........................9-40
PISTON & CONNECTING ROD -
REMOVAL...........................9-40
PISTON RING, FITTING.................9-42
PISTON TO CYLINDER BORE FITTING -
STANDARD PROCEDURE................9-30
PLASTIGAGE - STANDARD PROCEDURE,
MEASURING BEARING CLEARANCE
USING..............................9-11
PLATE LAMP BULB - INSTALLATION,
LICENSE...........................8L-45
PLATE LAMP BULB - REMOVAL,
LICENSE...........................8L-44
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-46
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-45
PLAY - STANDARD PROCEDURE,
CRANKSHAFT END....................9-33
PLUGS - STANDARD PROCEDURE,
ENGINE CORE AND OIL GALLERY.........9-9
POSITION LAMP BULB - INSTALLATION,
FRONT.............................8L-28
POSITION LAMP BULB - REMOVAL,
FRONT
.............................8L-28
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING
.........................7-2
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE
............................9-11
PRESS CONTAINER - DESCRIPTION,
COOLANT RECOVERY
..................7-20
PRESS CONTAINER - OPERATION,
COOLANT RECOVERY
..................7-20PRESSURE CAP - CLEANING, RADIATOR . . . 7-25
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-25
PRESSURE CAP - DIAGNOSIS AND
TESTING, RADIATOR...................7-25
PRESSURE CAP - INSPECTION,
RADIATOR...........................7-25
PRESSURE CAP - OPERATION,
RADIATOR...........................7-25
PRESSURE CHECKING - DIAGNOSIS AND
TESTING, ENGINE OIL..................9-46
PRESSURE LEAKAGE TEST - DIAGNOSIS
AND TESTING, CYLINDER
COMBUSTION.........................9-3
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-48
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-48
PRESSURE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMPRESSION.......9-3
PULLEY - INSTALLATION, TIMING BELT
TENSIONER..........................9-59
PULLEY - REMOVAL, TIMING BELT
TENSIONER..........................9-59
PUMP - 2.4L - DESCRIPTION, WATER.....7-27
PUMP - 2.4L - INSPECTION, WATER......7-28
PUMP - 2.4L - OPERATION, WATER.......7-27
PUMP - ASSEMBLY, OIL................9-50
PUMP - CLEANING, OIL................9-49
PUMP - DISASSEMBLY, OIL.............9-49
PUMP - INSPECTION, OIL...............9-50
PUMP - INSTALLATION, OIL.............9-50
PUMP - REMOVAL, OIL.................9-49
RADIATOR - CLEANING.................7-24
RADIATOR - DESCRIPTION..............7-22
RADIATOR - INSPECTION...............7-24
RADIATOR - INSTALLATION.............7-24
RADIATOR - REMOVAL.................7-22
RADIATOR FAN - ELECTRIC -
DESCRIPTION........................7-26
RADIATOR FAN - ELECTRIC -
INSTALLATION........................7-27
RADIATOR FAN - ELECTRIC -
OPERATION..........................7-26
RADIATOR FAN - ELECTRIC - REMOVAL . . . 7-26
RADIATOR PRESSURE CAP - CLEANING . . . 7-25
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-25
RADIATOR PRESSURE CAP - DIAGNOSIS
AND TESTING........................7-25
RADIATOR PRESSURE CAP -
INSPECTION.........................7-25
RADIATOR PRESSURE CAP - OPERATION . . 7-25
REAR - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-39
REAR - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-38
REAR FOG LAMP RELAY - DESCRIPTION . . 8L-56
REAR FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-57
REAR FOG LAMP RELAY -
INSTALLATION.......................8L-58
REAR FOG LAMP RELAY - OPERATION . . . 8L-57
REAR FOG LAMP RELAY - REMOVAL.....8L-58
REAR LAMP BULB - INSTALLATION......8L-59
REAR LAMP BULB - REMOVAL..........8L-59
REAR LAMP UNIT - INSTALLATION......8L-60
REAR LAMP UNIT - REMOVAL..........8L-59
REAR MOUNT - INSTALLATION..........9-45
REAR MOUNT - REMOVAL..............9-45
REAR SUSPENSION, SPECIAL TOOLS......2-6
RECOVERY PRESS CONTAINER -
DESCRIPTION, COOLANT...............7-20
RECOVERY PRESS CONTAINER -
OPERATION, COOLANT.................7-20
REFILLING COOLING SYSTEM -
STANDARD PROCEDURE................7-11
RELAY - DESCRIPTION, DAYTIME
RUNNING LAMP.....................8L-20
RELAY - DESCRIPTION, FRONT FOG
LAMP..............................8L-22
RELAY - DESCRIPTION, HEADLAMP
HIGH BEAM
.........................8L-33
RELAY - DESCRIPTION, HEADLAMP LOW
BEAM
..............................8L-39
RELAY - DESCRIPTION, PARK LAMP
.....8L-54
RELAY - DESCRIPTION, REAR FOG LAMP
. 8L-56
RELAY - DESCRIPTION, TRAILER TOW
....8L-62
KJINDEX 5
Description Group-Page Description Group-Page Description Group-Page

Page 1775 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual RELAY - DIAGNOSIS AND TESTING,
FRONT FOG LAMP....................8L-23
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP HIGH BEAM...............8L-34
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP LOW BEAM...........

RELAY - DIAGNOSIS AND TESTING,
FRONT FOG LAMP....................8L-23
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP HIGH BEAM...............8L-34
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP LOW BEAM...............8L-40
RELAY - DIAGNOSIS AND TESTING,
PARK LAMP.........................8L-55
RELAY - DIAGNOSIS AND TESTING,
REAR FOG LAMP.....................8L-57
RELAY - DIAGNOSIS AND TESTING,
TRAILER TOW.......................8L-62
RELAY - INSTALLATION, DAYTIME
RUNNING LAMP.....................8L-21
RELAY - INSTALLATION, FRONT FOG
LAMP..............................8L-24
RELAY - INSTALLATION, HEADLAMP
HIGH BEAM.........................8L-35
RELAY - INSTALLATION, HEADLAMP
LOW BEAM.........................8L-41
RELAY - INSTALLATION, PARK LAMP.....8L-56
RELAY - INSTALLATION, REAR FOG
LAMP..............................8L-58
RELAY - INSTALLATION, TRAILER TOW . . . 8L-63
RELAY - OPERATION, DAYTIME
RUNNING LAMP.....................8L-20
RELAY - OPERATION, FRONT FOG LAMP . . 8L-22
RELAY - OPERATION, HEADLAMP HIGH
BEAM..............................8L-33
RELAY - OPERATION, HEADLAMP LOW
BEAM..............................8L-39
RELAY - OPERATION, PARK LAMP.......8L-54
RELAY - OPERATION, REAR FOG LAMP . . . 8L-57
RELAY - OPERATION, TRAILER TOW.....8L-62
RELAY - REMOVAL, DAYTIME RUNNING
LAMP..............................8L-21
RELAY - REMOVAL, FRONT FOG LAMP . . . 8L-24
RELAY - REMOVAL, HEADLAMP HIGH
BEAM..............................8L-34
RELAY - REMOVAL, HEADLAMP LOW
BEAM..............................8L-40
RELAY - REMOVAL, PARK LAMP........8L-55
RELAY - REMOVAL, REAR FOG LAMP....8L-58
RELAY - REMOVAL, TRAILER TOW.......8L-63
REMOVAL - CLEANING.................9-55
REMOVAL - INSPECTION...............9-28
REMOVAL, 2.4L.......................7-20
REMOVAL, 2.4L.......................9-19
REMOVAL, 2.4L ENGINE....7-14,7-16,7-22,7-27
REMOVAL, BALANCE SHAFT.............9-60
REMOVAL, BALANCE SHAFT CARRIER.....9-64
REMOVAL, BALANCE SHAFT CHAIN.......9-64
REMOVAL, BRAKE LAMP SWITCH.......8L-17
REMOVAL, CAMSHAFT OIL SEAL(S).......9-22
REMOVAL, CAMSHAFT(S)...............9-24
REMOVAL, CATALYTIC CONVERTER.......11-2
REMOVAL, CENTER HIGH MOUNTED
STOP LAMP BULB....................8L-18
REMOVAL, CENTER HIGH MOUNTED
STOP LAMP UNIT....................8L-19
REMOVAL, CLEVIS BRACKET BUSHING.....2-2
REMOVAL, CRANKSHAFT...............9-33
REMOVAL, CRANKSHAFT OIL SEAL -
FRONT..............................9-37
REMOVAL, CRANKSHAFT OIL SEAL -
REAR...............................9-38
REMOVAL, CRANKSHAFT SPROCKET......9-55
REMOVAL, CROSS-OVER PIPE...........11-4
REMOVAL, CYLINDER HEAD.............9-20
REMOVAL, CYLINDER HEAD COVER.......9-26
REMOVAL, CYLINDER HEAD OFF.........9-27
REMOVAL, CYLINDER HEAD ON..........9-27
REMOVAL, DAYTIME RUNNING LAMP
RELAY.............................8L-21
REMOVAL, ENGINE ASSEMBLY...........9-12
REMOVAL, ENGINE COOLANT
TEMPERATURE SENSOR................7-21
REMOVAL, EXHAUST MANIFOLD.........9-53
REMOVAL, FRONT FOG LAMP BULB......8L-21
REMOVAL, FRONT FOG LAMP RELAY.....8L-24
REMOVAL, FRONT FOG LAMP UNIT......8L-24
REMOVAL, FRONT LAMP BULB.........8L-27
REMOVAL, FRONT LAMP UNIT
..........8L-27
REMOVAL, FRONT MOUNT
..............9-44
REMOVAL, FRONT POSITION LAMP
BULB
..............................8L-28
REMOVAL, HAZARD SWITCH
...........8L-29
REMOVAL, HEADLAMP BULB
...........8L-30REMOVAL, HEADLAMP HIGH BEAM
RELAY.............................8L-34
REMOVAL, HEADLAMP LEVELING
MOTOR............................8L-36
REMOVAL, HEADLAMP LEVELING
SWITCH............................8L-38
REMOVAL, HEADLAMP LOW BEAM
RELAY.............................8L-40
REMOVAL, HEADLAMP UNIT...........8L-41
REMOVAL, HYDRAULIC LIFTERS.........9-29
REMOVAL, INTAKE MANIFOLD...........9-52
REMOVAL, LAMP....................8L-66
REMOVAL, LAMP BAR................8L-65
REMOVAL, LAMP BAR SWITCH.........8L-67
REMOVAL, LICENSE PLATE LAMP BULB . . 8L-44
REMOVAL, LICENSE PLATE LAMP UNIT . . . 8L-45
REMOVAL, LOWER BALL JOINT...........2-5
REMOVAL, LOWER CONTROL ARM
BUSHING.............................2-2
REMOVAL, LOWER SUSPENSION ARM
BUSHING.............................2-7
REMOVAL, MUFFLER...................11-4
REMOVAL, MULTI-FUNCTION SWITCH....8L-53
REMOVAL, OIL FILTER.................9-47
REMOVAL, OIL PAN...................9-48
REMOVAL, OIL PUMP..................9-49
REMOVAL, PARK LAMP RELAY..........8L-55
REMOVAL, PISTON & CONNECTING ROD . . . 9-40
REMOVAL, RADIATOR..................7-22
REMOVAL, RADIATOR FAN - ELECTRIC....7-26
REMOVAL, REAR FOG LAMP RELAY......8L-58
REMOVAL, REAR LAMP BULB..........8L-59
REMOVAL, REAR LAMP UNIT...........8L-59
REMOVAL, REAR MOUNT...............9-45
REMOVAL, REPEATER LAMP BULB.......8L-60
REMOVAL, REPEATER LAMP UNIT.......8L-61
REMOVAL, RHD........................5-1
REMOVAL, ROCKER ARMS..............9-29
REMOVAL, STRUCTURAL COLLAR........9-44
REMOVAL, TIMING BELT................9-55
REMOVAL, TIMING BELT COVER(S).......9-53
REMOVAL, TIMING BELT TENSIONER &
PULLEY.............................9-59
REMOVAL, TRAILER TOW CONNECTOR . . . 8L-61
REMOVAL, TRAILER TOW RELAY........8L-63
REMOVAL, UPPER BALL JOINT...........2-6
REMOVAL, UPPER CONTROL ARM
BUSHINGS............................2-3
REMOVAL, UPPER SUSPENSION ARM
BUSHING.............................2-7
REMOVAL, VIBRATION DAMPER..........9-43
REPAIR OF DAMAGED OR WORN
THREADS - STANDARD PROCEDURE.......9-9
REPEATER LAMP BULB - INSTALLATION . . 8L-60
REPEATER LAMP BULB - REMOVAL......8L-60
REPEATER LAMP UNIT - INSTALLATION . . 8L-61
REPEATER LAMP UNIT - REMOVAL......8L-61
REVERSE FLUSHING - STANDARD
PROCEDURE, COOLING SYSTEM.........7-12
RHD - INSTALLATION...................5-1
RHD - REMOVAL.......................5-1
RING, FITTING - PISTON................9-42
ROCKER ARMS - INSPECTION...........9-30
ROCKER ARMS - INSTALLATION.........9-30
ROCKER ARMS - REMOVAL.............9-29
ROD - DESCRIPTION, PISTON &
CONNECTING.........................9-40
ROD - INSTALLATION, PISTON &
CONNECTING.........................9-41
ROD - OPERATION, PISTON &
CONNECTING.........................9-40
ROD - REMOVAL, PISTON &
CONNECTING.........................9-40
ROD, FITTING - CONNECTING............9-32
RUNNING LAMP RELAY - DESCRIPTION,
DAYTIME...........................8L-20
RUNNING LAMP RELAY - INSTALLATION,
DAYTIME...........................8L-21
RUNNING LAMP RELAY - OPERATION,
DAYTIME
...........................8L-20
RUNNING LAMP RELAY - REMOVAL,
DAYTIME
...........................8L-21
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL
.....................9-37
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL
.....................9-37
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL
.....................9-39SEAL - REAR - REMOVAL, CRANKSHAFT
OIL ................................9-38
SEALERS - STANDARD PROCEDURE,
FORM-IN-PLACE GASKETS..............9-10
SEAL(S) - INSTALLATION, CAMSHAFT
OIL ................................9-22
SEAL(S) - REMOVAL, CAMSHAFT OIL.....9-22
SEATS - CLEANING, INTAKE/EXHAUST
VALVES .............................9-27
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES.....................9-27
SENSOR - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-22
SENSOR - OPERATION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - REMOVAL, ENGINE COOLANT
TEMPERATURE.......................7-21
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE..........................9-48
SENSOR/SWITCH - OPERATION, OIL
PRESSURE..........................9-48
SERPENTINE DRIVE BELT DIAGNOSIS -
DIAGNOSIS AND TESTING..............7-15
SHAFT - DESCRIPTION, BALANCE........9-59
SHAFT - OPERATION, BALANCE..........9-59
SHAFT - REMOVAL, BALANCE...........9-60
SHAFT CARRIER - INSTALLATION,
BALANCE............................9-64
SHAFT CARRIER - REMOVAL, BALANCE....9-64
SHAFT CHAIN - INSTALLATION,
BALANCE............................9-64
SHAFT CHAIN - REMOVAL, BALANCE......9-64
SHAFT TIMING, INSTALLATION -
BALANCE............................9-61
SHIELDS - DESCRIPTION, HEAT..........11-4
SPECIAL TOOLS - 2.4L ENGINE..........9-17
SPECIAL TOOLS - COOLING.............7-13
SPECIAL TOOLS - FRONT SUSPENSION.....2-1
SPECIAL TOOLS - REAR SUSPENSION......2-6
SPECIFICATIONS - TORQUE.............7-13
SPECIFICATIONS, 2.4L ENGINE...........9-13
SPECIFICATIONS, LAMPS/LIGHTING -
EXTERIOR..........................8L-15
SPECIFICATIONS, TORQUE..............9-16
SPROCKET - INSTALLATION,
CRANKSHAFT........................9-56
SPROCKET - REMOVAL, CRANKSHAFT.....9-55
STANDARD PROCEDURE - CLEANING.....9-31
STANDARD PROCEDURE - ENGINE OIL
LEVEL CHECK........................9-47
STANDARD PROCEDURE - INSPECTION....9-32
STANDARD PROCEDURE, CAMSHAFT
END-PLAY...........................9-23
STANDARD PROCEDURE, COOLING
SYSTEM - REVERSE FLUSHING..........7-12
STANDARD PROCEDURE, CRANKSHAFT
END PLAY ...........................9-33
STANDARD PROCEDURE, CYLINDER
BORE HONING........................9-31
STANDARD PROCEDURE, DRAINING
COOLING SYSTEM....................7-11
STANDARD PROCEDURE, ENGINE CORE
AND OIL GALLERY PLUGS...............9-9
STANDARD PROCEDURE, ENGINE
GASKET SURFACE PREPARATION.........9-11
STANDARD PROCEDURE, ENGINE OIL
AND FILTER CHANGE..................9-47
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES.................7-30
STANDARD PROCEDURE, FORM-IN-
PLACE GASKETS AND SEALERS..........9-10
STANDARD PROCEDURE, HYDROSTATIC
LOCKED ENGINE.......................9-9
STANDARD PROCEDURE, LAMP BAR
AIMING............................8L-65
STANDARD PROCEDURE, MAIN BEARING
- FITTING
............................9-35
STANDARD PROCEDURE, MEASURING
BEARING CLEARANCE USING
PLASTIGAGE
.........................9-11
STANDARD PROCEDURE, PISTON TO
CYLINDER BORE FITTING
...............9-30
STANDARD PROCEDURE, REFILLING
COOLING SYSTEM
....................7-11
STANDARD PROCEDURE, REPAIR OF
DAMAGED OR WORN THREADS
...........9-9
6 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

Page 1784 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual Starter2.4L Eng3.7L Eng
STARTER Contd
56041436M m .9 159.0056041641AC m 1.8 159.0035 I-
r~..:::---~ ~;i:i~:~"
4~
Use Procedure Explanation 13 with the following tex!.R&IWindshield ...#2.7#Includes C

Starter2.4L Eng3.7L Eng
STARTER Cont'd
56041436M m .9 159.0056041641AC m 1.8 159.0035 I-
r~..:::---~ ~;i:i~:~'"
4~
Use Procedure Explanation 13 with the following tex!.R&IWindshield ...#2.7#Includes Clean Up Old Adhesive as Necessary
5 ~8
~~~~ -,
S-(::~:~~::~~:::::::~ ,,~(" p-~~ ~
\\\
f,
~
'~
):1
004-09541
1 Cover, Cowl 55155850AB.3 102.002 Pin, Cowl (4) 6501925 1.853 Seal, Cowl 55235927AA.1 16.254 Panel, Dash 55177300AB #7.0 127.00#W/Plenum Panel Removed Deduct 2.05 Panel, Plenum 55176767AC 7.0 270.00
\\\
4~1'"~
JEEP LIBERTY 2002
ELECTRICALCont'd2211 racket, Instrument anel9- 12 Bracket, Hush Panel 78 7.60
113 Kit, Radio Bracke~ 5072596M 11.701]lncludes Both Sides14 Bracket, Audio Equipment 5072606M 10.4515 Striker} Glove Box Latch 5072605M 25.4516 Brk! KI!t Passenger Air Bag-See Air Bag System Section11 Latch, ulove BoxSlate Gray WQ54XDVM.1 35.50Taupe WQ54WL8AA.1 24.8518 Module, PassenQer Air Bag-See Air Bag System Section19 Bracket, Lower Steeling Column 5531498TAA 154.0020 Box, GloveSlate Gray WC86XDVAA #.2 219.00Taupe WC86WL8AA #.2 219.00#Includes R&R Glove Box Latch21 Bezel, CenterLimited Model WA96DX9AA.3 92.75Renegade, Sport Model 5072479AA .3 180.0022 Knob, Li9hter 4685536 12.0023 Outlet, Lighter 4793554 11.0024 Ashtray WA97DX9AA 25.0025 SpeakerStandard AiL 56038610AC 43.00Premium AiL 56038594AC 73.0026 Bracket, UpperSt~ring Column 55314992AA 9.85
~/-
~313028
r:l-32I27
8-34 004-09924
2
7
5WIPER SYSTEM
213 I!
""""",~~~~-~~~4
5
~,..~6
,--d
~ :: 1
11~~~ ~ 19 ~14 .7
21~h13 4 1822 r:13 IIII ~ L16 15~ 18!Jj,j17~ 'j;--16 ~-" ~24 ~ ~
1~20 004-09923
7lf26--
?7 Cluster Ass~Black 56010151AF m .9 445.00Chrome 56010461AF m .9 454.00llAdditional Palts &/or Dealer Contact Required28 Lens, Cluster (a)Black 4728962AB m 1.0 0.00Chrome 4832731AB m 1.0 46.45la) Included wlCluster Assy29 RadioCode RBP 56038586AD.5 650.00Code RBY 56038583AD.5 0.00Code RBB 56038588AG.5 390.00Code RAD 56038585AD.5 1170.00Code RBK 56038589AH.5 460.00Code RBT 56038584AD.5 0.0030 Changer, CD 82203465 .5 345.00131 Cable, CD Changer 56038596AE 37.7032 Switch, Mirror 56010093AA #.2 22.95#Included in R&R Left Front Door Trim Panel, NotIncluded in R&R Instrument Panel33 Switch;, Climate ControlI wi Nv 55037533AB m .5 80.00wlo NC 55037531AB m .5 62.95134 Knob, Climate Controlll 5069169AA 1.451]As Required
8004-09540
on
6--<:~
#1.1
,-"-;:;;;;;;::~4~10 1
WD851DVAAWD851LSAA
WD581DVAAWD581L8AA
WD591DVAAWD591L8AB5072905AA5072906AA
.6 29.35.6 29.35
.6 43.00.6 43.00
#.2 92.85#.2 92.85#.2 10.00#.2 118.00
Use Procedure Explanations 14 and 28 with the following text.Refinish Dash Panel 1.5Refinish Plenum Panel 1.0
Labor Times Shown are for Replacement with New OEM Undamaged Parts on New Undamaged Vehicles.Comments or suggestions? Need assistance? Call 1.800-854-7030 or 8!;8/578-6550, Ext 8220. Fax 1-888-256-7969 or 858/549-0629.570CH
' 2 004-09922
1 Glass, WindshieldChrysler 55235913AC #2.3 0.00 ...NAGS c DW01449GBN #2.3 958.30 Use Procedure Explanation 14 with the following text.#Includes Clean Up Otd Adhesive as Necessary R&llnstrument Panel.. m #5.02 Spacer, Windshield /4) 55360509AA .35 #tncludes R&I Steering Column & Floor Console3 Mould!ng. Upper W/$ 55235917AB 9.60 NOTE: All Parts in this section are included in R&R4 Moulding. Side WIS R 55360052AB .2 58.85 Instrument Panel unless noted otherwiseL 55360053AB .2 58.85 .
5 Mirror, Rear View 4805332AB .2 19.45 16 Button, Rear View Mirror 55076401 8.25 25-{!:Q7 Moulding, Inr W/S Garnish R 5GM92TL2AC .3 46.35 6-0L 5GM93TL2AC .3 46.3598 Visor, Sun 5Illuminated R UY66TL2AA .2 103.00 I 10 6L UY67TL2AA .2 106.00 ~Non-Illuminated R UY64TL2AA .2 61.95 ~ 6 1L UY65TL2AA .2 63.70 ()\4Clip, Visor R/L 5072343AA 2.60
4 Arm, Wiper R 5666970AAL 5066968AA#Includes R&R Wiper Blade5 Module, Wiper 55155895AA6 Reservoir, Washer 5066867AA#Includes R&I/R&R Air Cleaner Assy7 Cap, Reservoir 5066881AA8 Pump, WasherTo 8-3-01 5066880AAFrom 8-3-01 5018129ACGrommet Pump 5011809AA9 Sensor, Fluid Level 4882797Grommet, Sensor 5013755AANozzle, Washer AiL 55155854AB#Included in R&R Cowl Cover
Use Procedure Explanation 14 with the following text.R&IFloorConsole .3
NOTE: All Parts in this section are included in R&R FloorConsole unless noted otherwise.
2
~~~~~~
,~-.- ,-,..1'70 3 Door, Passenger Air Bag-See Air Bag System Section1 16'60 4 Panel, Instrument.116'60Slate Gray..To 6-14-01 WC85XDVAA m #6.5 517.00#.2 24.10 From 6-14-01 WC85XDVAB m#6.5 517.00#.2 26.00 Taupe
To 6-14-01 WC85WL8AA m #6.5 517,0078,35 From 6-14-01 WC85WL8AB m #6.5 517,0078.50 #Includes R&I Steering Column & Floor Console25005 Bracket, Instrument Panel R 5073523AA 39.95, L 5072615AA 30,8588 45 6 Grille, Instrument Panel (4) WC88DX9AA .1 0,00.7 Cover, Instrument Panel531.1100Slate Gray R 5GN55XDVAD .1 10,95, L 5GK19XDVAD .1 17,5094,2005 Taupe R 5GN55WL8AD .1 10.95, L 5GK19WL8AD .1 17,50#.2 10,00 8 Bezel, No.1 Instrument PanelLimted Model WB02DX9AA.2 30,70 004-09544Renegade, Sport ModelSlate Gray WB021DVAA.2 30.70 1 Console, FloorTaupe WB021L8AA.2 30,70 Man Trans9 Bezel, No.2 Instrument Panel Slate GrayLimited Model WB03DX9AA.1 25,45 TaupeRenegade, Sport Model Auto TransSlate Gray WB031DVAA.1 25.45 Slate GrayTaupe WB031 L8AA .1 25.45 Taupe10 Bezel, No.3 Instrument Panel 2 Lid, ConsoleLimited Model WB05DX9AA.1 22.10 Slate Grayi Renegade, Sport Model TaupeISlate Gray WB051DVAA.1 22.10 3 Latch, LidTaupe WB051l8AA.1 22.10 4 Hinge, Lid

Page 1792 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual JEEP
ž
2002
LIBERTY
SERVICE MANUAL and
2.4L GAS SUPPLEMENT
To order the special service tools used and
illustrated, please refer to the instructions on
inside back cover.
NO PART OF THIS PUBLICATION

Load next 8 pages

Page: < prev 1-10 ... 81-88 89-96 97-104 105-112 113-120 121-128 next >

diagram open hood oil filter isofix reset infotainment system service interval reset