2002 JEEP LIBERTY alignment

GLASS PANEL
REMOVAL
(1) Slide sunshade rearward to the open position.
(2) Move the glass panel to the closed position.
(3) Remove the four glass panel screws (Fig. 1).
(4) Lift off glass panel and remove from vehicle.
INSTALLATION
(1) Position glass panel on to mechanism lift arm.
(2) Start the four attaching screws.
(3) Center glass in opening by running a business
card around the glass.
(4) Adjust glass panel. (Refer to 23 - BODY/SUN-
ROOF/GLASS PANEL - ADJUSTMENTS)
ADJUSTMENTS
SUNROOF GLASS PANEL ADJUSTMENT
(1) Move the sunshade rearward to the open posi-
tion.
(2) Move the sunroof glass panel to the fully closed
position.
(3) Adjust the glass one corner at a time.
(a) Loosen four glass screws (Fig. 2).
(b) Lift glass assembly and align the top of the
glass panel to the top of the roof panel.
(c) Tighten screw to 3.5 N´m (31 in. lbs.).
(d) Repeat steps a. and b. for each corner of the
glass panel.
(e) When properly adjusted, the front of the
glass panel is 1.75 mm (0.07 in.) to 2.75 mm (0.11
in.) lower than the roof surface and the rear edgeof the glass panel is 1.75mm (0.07 in.) to .75 mm
(0.03 in.) lower than the roof surface.
NOTE: Glass assembly seal is 2.5mm (0.1 in) higher
than the glass panel. Measure at 300mm (11.8 in)
outboard of the centerline of the vehicle.
(4) Verify sunroof operation and alignment. Check
fit and re-adjust as necessary.
GLASS PANEL SEAL
REMOVAL
(1) Remove sunroof glass panel. (Refer to 23 -
BODY/SUNROOF/GLASS PANEL - REMOVAL)
(2) Place glass panel on clean work area with the
top side up. Support the glass assembly from under-
side to avoid bending or otherwise damaging the
mounting tabs.
(3) Grasp the seal and pull seal away from the
glass panel. The seal is a one piece seal.
INSTALLATION
NOTE: Always position seal seam on center of the
passenger side of glass panel.
(1) Place seal into position.
(2) Install seal on glass. Using care working the
seal around the glass, being careful not to over
stretch the seal while installing.
(3) Install the glass panel. (Refer to 23 - BODY/
SUNROOF/GLASS PANEL - INSTALLATION)
Fig. 1 GLASS PANEL
1 - SCREWS
2 - GLASS PANEL
3 - MODULE ASSEMBLYFig. 2 GLASS PANEL
1 - SCREWS
2 - GLASS PANEL
3 - MODULE ASSEMBLY
23 - 178 SUNROOFKJ

(4) Test sunroof operation, adjust as necessary.
(5) Install headliner. (Refer to 23 - BODY/INTERI-
OR/HEADLINER - INSTALLATION)
CONTROL MODULE
REMOVAL
(1) Remove the module assembly. (Refer to 23 -
BODY/SUNROOF/MODULE ASSEMBLY -
REMOVAL)
(2) Remove three motor assembly retaining screws
from bottom side of motor, and remove motor assem-
bly (Fig. 11).
(3) From top side of module assembly, remove one
attaching screw from electronics module. (Fig. 12)
(4) Remove old timing module.
INSTALLATION
(1) Check glass assembly position. Adjust to full
closed position. Insert pin into holes in lift arm
assembly to check position (Fig. 13).
(2) Set new electronic module in position on top
side of motor mounting bracket engaging drive cables
with pinion gear in electronics module.
(3) Install one screw to attach electronics module
to motor bracket. Tighten screw to 3 N´m (27 in. lbs.)
torque.
(4) Install motor assembly to motor bracket and
electronics module with three screws. Tighten screw
to 1.75 N´m (15.5 in. lbs.) torque.
(5) Remove the new module's timing pin and dis-
card. (Fig. 14)(6) Connect electrical connector to module assem-
bly wire harness. Secure any loose wires.
(7) Install module assembly. (Refer to 23 - BODY/
SUNROOF/MODULE ASSEMBLY - INSTALLA-
TION)
(8) Test operation, adjust as necessary. (Refer to 23
- BODY/SUNROOF/GLASS PANEL - ADJUST-
MENTS)
(9) Install opening trim lace. (Refer to 23 - BODY/
SUNROOF/OPENING TRIM LACE - INSTALLA-
TION)
Fig. 12 CONTROL MODULE
1 - MOTOR BRACKET
2 - CABLES
3 - SCREW
4 - CONTROL MODULE
Fig. 13 LIFT ARM POSITIONING
1 - GLASS BRACKET
2 - LIFT ARM
3 - ALIGNMENT PIN
Fig. 14 MODULE TIMING PIN
1 - CONTROL MODULE
2 - TIMING PIN
KJSUNROOF 23 - 183
DRIVE MOTOR (Continued)

ABS - DESCRIPTION, BRAKES...........5-32
ABS - OPERATION, BRAKES.............5-32
ABS - SPECIFICATIONS, BRAKES.........5-33
ABS BRAKE BLEEDING - STANDARD
PROCEDURE.........................5-33
ABS INDICATOR - DESCRIPTION.........8J-11
ABS INDICATOR - OPERATION..........8J-11
A/C APPLICATION TABLE,
SPECIFICATIONS......................24-9
A/C COMPRESSOR CLUTCH -
INSPECTION........................24-14
A/C COMPRESSOR CLUTCH -
INSTALLATION.......................24-14
A/C COMPRESSOR CLUTCH - REMOVAL . . 24-13
A/C COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE...............24-12
A/C COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-12
A/C COMPRESSOR CLUTCH RELAY -
DESCRIPTION.......................24-15
A/C COMPRESSOR CLUTCH RELAY -
INSTALLATION.......................24-16
A/C COMPRESSOR CLUTCH RELAY -
OPERATION.........................24-15
A/C COMPRESSOR CLUTCH RELAY -
REMOVAL..........................24-16
A/C COMPRESSOR NOISE - DIAGNOSIS
AND TESTING.......................24-42
A/C CONDENSER - DESCRIPTION........24-45
A/C CONDENSER - INSTALLATION.......24-46
A/C CONDENSER - OPERATION...........24-45
A/C CONDENSER - REMOVAL...........24-45
A/C DISCHARGE LINE - INSTALLATION . . . 24-47
A/C DISCHARGE LINE - REMOVAL.......24-46
A/C EVAPORATOR - DESCRIPTION.......24-49
A/C EVAPORATOR - INSTALLATION......24-49
A/C EVAPORATOR - OPERATION.........24-49
A/C EVAPORATOR - REMOVAL..........24-49
A/C HEATER CONTROL - DESCRIPTION . . . 24-16
A/C HEATER CONTROL - INSTALLATION . . . 24-17
A/C HEATER CONTROL - REMOVAL......24-17
A/C HIGH PRESSURE SWITCH -
DESCRIPTION.......................24-17
A/C HIGH PRESSURE SWITCH -
DIAGNOSIS AND TESTING.............24-18
A/C HIGH PRESSURE SWITCH -
INSTALLATION.......................24-18
A/C HIGH PRESSURE SWITCH -
OPERATION.........................24-18
A/C HIGH PRESSURE SWITCH -
REMOVAL..........................24-18
A/C LIQUID LINE - INSTALLATION.......24-47
A/C LIQUID LINE - REMOVAL...........24-47
A/C LOW PRESSURE SWITCH -
DESCRIPTION.......................24-18
A/C LOW PRESSURE SWITCH -
DIAGNOSIS AND TESTING.............24-19
A/C LOW PRESSURE SWITCH -
INSTALLATION.......................24-19
A/C LOW PRESSURE SWITCH -
OPERATION.........................24-18
A/C LOW PRESSURE SWITCH -
REMOVAL..........................24-19
A/C ORIFICE TUBE - DESCRIPTION.......24-50
A/C ORIFICE TUBE - INSTALLATION......24-50
A/C ORIFICE TUBE - OPERATION........24-50
A/C ORIFICE TUBE - REMOVAL..........24-50
A/C PERFORMANCE - DIAGNOSIS AND
TESTING............................24-2
A/C SUCTION LINE - INSTALLATION......24-49
A/C SUCTION LINE - REMOVAL.........24-48
ACCELERATOR PEDAL - INSTALLATION . . . 14-30
ACCELERATOR PEDAL - REMOVAL.......14-29
ACCESS PANEL - DESCRIPTION, LATCH . . 23-139
ACCESS PANEL - INSTALLATION, LATCH . 23-139
ACCESS PANEL - REMOVAL, LATCH.....23-139
ACCUMULATOR - DESCRIPTION.........24-51
ACCUMULATOR - INSTALLATION........24-51
ACCUMULATOR - OPERATION..........24-51
ACCUMULATOR - REMOVAL
............24-51
ACTUATION TEST MODE - DESCRIPTION,
CIRCUIT
.............................25-2
ACTUATOR - INSTALLATION, BLEND
DOOR
.............................24-20
ACTUATOR - INSTALLATION, FLOOR -
DEFROST DOOR
.....................24-25
ACTUATOR - INSTALLATION, PANEL
DOOR
.............................24-25ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-26
ACTUATOR - REMOVAL, BLEND DOOR....24-20
ACTUATOR - REMOVAL, FLOOR -
DEFROST DOOR.....................24-24
ACTUATOR - REMOVAL, PANEL DOOR....24-24
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-26
ADAPTER - INSTALLATION, DISC BRAKE
CALIPER............................5-18
ADAPTER - REMOVAL, DISC BRAKE
CALIPER............................5-18
ADAPTER HOUSING SEAL -
INSTALLATION......................21-124
ADAPTER HOUSING SEAL - REMOVAL . . . 21-124
ADAPTOR - REMOVAL, DEFROST
DUCT/DEMISTER.....................24-32
ADHESIVE LOCATIONS -
SPECIFICATIONS, WELD AND
STRUCTURAL........................23-9
ADJUSTER - DIAGNOSIS AND TESTING,
HYDRAULIC LASH.................9-19,9-30
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP.....................8O-38
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP.....................8O-37
ADJUSTMENT - STANDARD
PROCEDURE, CAMBER AND CASTER.......2-5
ADJUSTMENT - STANDARD
PROCEDURE, CAMBER, CASTER AND
TOE .................................2-5
ADJUSTMENT - STANDARD
PROCEDURE, COMPASS VARIATION......8M-3
ADJUSTMENT - STANDARD
PROCEDURE, TOE......................2-5
ADJUSTMENT, ADJUSTMENTS . . . 23-119,23-124,
23-131
ADJUSTMENT, ADJUSTMENTS...........3-55
ADJUSTMENT, ADJUSTMENTS -
SUNROOF GLASS PANEL.............23-178
ADJUSTMENT, FRONT FOG LAMP UNIT . . . 8L-25
ADJUSTMENT, HEADLAMP UNIT.........8L-42
ADJUSTMENT, LOCK OUT...............5-30
ADJUSTMENT, REAR DRUM BRAKE.......5-12
ADJUSTMENTS - ADJUSTMENT . . 23-119,23-124,
23-131
ADJUSTMENTS - ADJUSTMENT..........3-55
ADJUSTMENTS - SUNROOF GLASS
PANEL ADJUSTMENT................23-178
ADJUSTMENTS, FRONT AXLE - 186FIA....3-25
ADJUSTMENTS, GEARSHIFT CABLE.....21-130
ADJUSTMENTS, PARK-INTERLOCK
CABLE............................21-154
ADJUSTMENTS, REAR AXLE - 8 1/4 .......3-92
AFTER A SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE.................8O-6
AIR CHECKING TRANSMISSION CLUTCH
OPERATION - DIAGNOSIS AND
TESTING...........................21-80
AIR CONDITIONER - DESCRIPTION,
HEATER .............................24-1
AIR CONDITIONER - OPERATION,
HEATER .............................24-2
AIR CONTROL MOTOR - DESCRIPTION,
IDLE...............................14-35
AIR CONTROL MOTOR - INSTALLATION,
IDLE...............................14-36
AIR CONTROL MOTOR - OPERATION,
IDLE...............................14-35
AIR CONTROL MOTOR - REMOVAL, IDLE . . 14-36
AIR TEMPERATURE SENSOR -
DESCRIPTION, INTAKE................14-36
AIR TEMPERATURE SENSOR -
INSTALLATION, INTAKE................14-38
AIR TEMPERATURE SENSOR -
OPERATION, INTAKE..................14-36
AIR TEMPERATURE SENSOR -
REMOVAL, INTAKE...................14-37
AIRBAG - DESCRIPTION, DRIVER........8O-17
AIRBAG - DESCRIPTION, PASSENGER....8O-27
AIRBAG - DESCRIPTION, SIDE CURTAIN . . 8O-38
AIRBAG - INSTALLATION, DRIVER.......8O-20
AIRBAG - INSTALLATION, PASSENGER
. . . 8O-29
AIRBAG - INSTALLATION, SIDE CURTAIN
. . 8O-41
AIRBAG - OPERATION, DRIVER
.........8O-18
AIRBAG - OPERATION, PASSENGER
......8O-27
AIRBAG - OPERATION, SIDE CURTAIN
....8O-39AIRBAG - REMOVAL, DRIVER...........8O-19
AIRBAG - REMOVAL, PASSENGER.......8O-28
AIRBAG - REMOVAL, SIDE CURTAIN.....8O-40
AIRBAG CONTROL MODULE -
DESCRIPTION........................8O-9
AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE IMPACT...........8O-43
AIRBAG CONTROL MODULE -
INSTALLATION......................8O-12
AIRBAG CONTROL MODULE -
INSTALLATION, SIDE IMPACT...........8O-45
AIRBAG CONTROL MODULE -
OPERATION.........................8O-10
AIRBAG CONTROL MODULE -
OPERATION, SIDE IMPACT.............8O-43
AIRBAG CONTROL MODULE - REMOVAL . . 8O-11
AIRBAG CONTROL MODULE - REMOVAL,
SIDE IMPACT.......................8O-44
AIRBAG DOOR - INSTALLATION,
PASSENGER........................8O-30
AIRBAG DOOR - REMOVAL, PASSENGER . . 8O-29
AIRBAG INDICATOR - DESCRIPTION......8J-12
AIRBAG INDICATOR - OPERATION.......8J-12
AIRBAG MOUNTING BRACKET -
INSTALLATION, PASSENGER...........8O-31
AIRBAG MOUNTING BRACKET -
REMOVAL, PASSENGER...............8O-31
AJAR INDICATOR - DESCRIPTION, DOOR . . 8J-17
AJAR INDICATOR - DESCRIPTION, GATE . . 8J-20
AJAR INDICATOR - DESCRIPTION,
GLASS..............................8J-21
AJAR INDICATOR - OPERATION, DOOR . . . 8J-17
AJAR INDICATOR - OPERATION, GATE....8J-20
AJAR INDICATOR - OPERATION, GLASS . . . 8J-21
AJAR SWITCH - DESCRIPTION, DOOR....8L-77
AJAR SWITCH - DESCRIPTION, FLIP-UP
GLASS.............................8L-77
AJAR SWITCH - DESCRIPTION, HOOD....8Q-11
AJAR SWITCH - DESCRIPTION,
TAILGATE...........................8L-82
AJAR SWITCH - DIAGNOSIS AND
TESTING, HOOD.....................8Q-12
AJAR SWITCH - INSTALLATION, HOOD . . . 8Q-12
AJAR SWITCH - OPERATION, DOOR......8L-77
AJAR SWITCH - OPERATION, FLIP-UP
GLASS.............................8L-77
AJAR SWITCH - OPERATION, HOOD.....8Q-12
AJAR SWITCH - OPERATION, TAILGATE . . . 8L-82
AJAR SWITCH - REMOVAL, HOOD.......8Q-12
AJAR SWITCH BRACKET -
INSTALLATION, HOOD.................8Q-13
AJAR SWITCH BRACKET - REMOVAL,
HOOD.............................8Q-13
AJAR SWITCH STRIKER -
INSTALLATION, HOOD.................8Q-14
AJAR SWITCH STRIKER - REMOVAL,
HOOD.............................8Q-13
ALIGNMENT - DESCRIPTION, WHEEL.......2-3
ALIGNMENT - OPERATION, WHEEL........2-3
ALIGNMENT, SPECIFICATIONS............2-6
ALUMINUM THREAD REPAIR -
STANDARD PROCEDURE...............21-81
AMBIENT TEMP SENSOR - DESCRIPTION . . 8M-9
AMBIENT TEMP SENSOR - OPERATION . . . 8M-9
AMBIENT TEMPERATURE SENSOR -
DIAGNOSIS AND TESTING..............8M-9
AMBIENT TEMPERATURE SENSOR
CIRCUIT - DIAGNOSIS AND TESTING.....8M-9
AMPERAGE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP.................14-16
AMPLIFIER CHOKE AND RELAY -
DESCRIPTION........................8A-3
AMPLIFIER CHOKE AND RELAY -
DIAGNOSIS AND TESTING..............8A-4
AMPLIFIER CHOKE AND RELAY -
INSTALLATION.......................8A-4
AMPLIFIER CHOKE AND RELAY -
OPERATION..........................8A-3
AMPLIFIER CHOKE AND RELAY -
REMOVAL...........................8A-4
ANCHOR - DESCRIPTION, CHILD TETHER
. 8O-13
ANCHOR - OPERATION, CHILD TETHER
. . . 8O-13
ANGLE - STANDARD PROCEDURES,
PROPELLER SHAFT
.....................3-3
ANTENNA BODY & CABLE -
DESCRIPTION
........................8A-4
ANTENNA BODY & CABLE -
INSTALLATION
.......................8A-6
KJINDEX 1
Description Group-Page Description Group-Page Description Group-Page

VALVE - INSTALLATION, FLOW
MANAGEMENT.......................14-7
VALVE - INSTALLATION, FRONT CHECK....8R-9
VALVE - INSTALLATION, FUEL TANK
CHECK.............................14-28
VALVE - INSTALLATION, PCV...........25-32
VALVE - INSTALLATION, REAR CHECK....8R-35
VALVE - INSTALLATION, VACUUM CHECK . 24-28
VALVE - OPERATION, FLOW
MANAGEMENT.......................14-6
VALVE - OPERATION, FRONT CHECK......8R-9
VALVE - OPERATION, FUEL TANK CHECK . . 14-28
VALVE - OPERATION, HIGH PRESSURE
RELIEF.............................24-42
VALVE - OPERATION, PCV..............25-31
VALVE - OPERATION, REAR CHECK......8R-34
VALVE - OPERATION, SOLENOID SWITCH . 21-161
VALVE - OPERATION, VACUUM CHECK....24-28
VALVE - REMOVAL, FLOW
MANAGEMENT.......................14-6
VALVE - REMOVAL, FRONT CHECK.......8R-9
VALVE - REMOVAL, FUEL TANK CHECK . . . 14-28
VALVE - REMOVAL, PCV...............25-32
VALVE - REMOVAL, REAR CHECK.......8R-34
VALVE - REMOVAL, VACUUM CHECK.....24-28
VALVE BODY - ASSEMBLY............21-176
VALVE BODY - CLEANING.............21-175
VALVE BODY - DESCRIPTION............21-171
VALVE BODY - DISASSEMBLY..........21-173
VALVE BODY - INSPECTION...........21-175
VALVE BODY - INSTALLATION..........21-177
VALVE BODY - OPERATION............21-171
VALVE BODY - REMOVAL.............21-172
VALVE GUIDE SEALS - DESCRIPTION . . 9-29,9-38
VALVE GUIDES - DESCRIPTION......9-19,9-30
VALVE SPRINGS - DESCRIPTION.....9-29,9-38
VALVE SPRINGS - INSTALLATION.....9-29,9-38
VALVE SPRINGS - REMOVAL........9-29,9-38
VALVE TIMING - DESCRIPTION...........9-71
VALVE TIMING - OPERATION............9-71
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST.................9-28,9-36
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST.................9-27,9-35
VANITY LAMP BULB - INSTALLATION.....8L-84
VANITY LAMP BULB - REMOVAL........8L-83
VAPOR CANISTER - DESCRIPTION.......25-33
VAPOR CANISTER - INSTALLATION......25-33
VAPOR CANISTER - OPERATION.........25-33
VAPOR CANISTER - REMOVAL..........25-33
VARIATION ADJUSTMENT - STANDARD
PROCEDURE, COMPASS...............8M-3
VEHICLE EMISSION CONTROL
INFORMATION (VECI) LABEL -
DESCRIPTION......................Intro.-8
VEHICLE IDENTIFICATION NUMBER -
DESCRIPTION......................Intro.-8
VEHICLE SAFETY CERTIFICATION LABEL
- DESCRIPTION.....................Intro.-9
VEHICLE THEFT SECURITY -
DESCRIPTION........................8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-3
VEHICLE THEFT SECURITY SYSTEM -
DIAGNOSIS AND TESTING..............8Q-6
VERIFICATION TEST - STANDARD
PROCEDURE.........................8O-8
VIBRATION - DIAGNOSIS AND TESTING,
TIRE NOISE OR.......................22-8
VIBRATION DAMPER - INSTALLATION.....9-55
VIBRATION DAMPER - REMOVAL.........9-54
VIEW MIRROR - INSTALLATION, SIDE . . . 23-145
VIEW MIRROR - REMOVAL, REAR......23-161
VIEW MIRROR - REMOVAL, SIDE.......23-145
VISCOUS - CLEANING, RADIATOR - FAN . . . 7-29
VISCOUS - DESCRIPTION, RADIATOR -
FAN ................................7-27
VISCOUS - INSPECTION, RADIATOR -
FAN ................................7-29
VISCOUS - INSTALLATION, RADIATOR -
FAN
................................7-29
VISCOUS - OPERATION, RADIATOR -
FAN
................................7-27
VISCOUS - REMOVAL, RADIATOR - FAN
....7-28
VISCOUS FAN DRIVE - DIAGNOSIS AND
TESTING
............................7-28
VISOR - INSTALLATION, SUN
..........23-160VISOR - REMOVAL, SUN..............23-160
VISOR SUPPORT - INSTALLATION, SUN . . 23-160
VISOR SUPPORT - REMOVAL, SUN.....23-160
VOLT SUPPLIES - DESCRIPTION, 5......8E-13
VOLT SUPPLIES - OPERATION, 5........8E-15
VOLTAGE DROP - STANDARD
PROCEDURE, TESTING FOR A.......8W-01-10
VOLTAGE POTENTIAL - STANDARD
PROCEDURE, TESTING OF...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION....8F-31
VOLTAGE REGULATOR - OPERATION.....8F-31
VOLTAGE TEST - STANDARD
PROCEDURE, OPEN-CIRCUIT...........8F-12
VOLUME CHECK - STANDARD
PROCEDURE, OIL PUMP..............21-148
WAIT-TO-START INDICATOR -
DESCRIPTION.......................8J-35
WAIT-TO-START INDICATOR -
OPERATION.........................8J-35
WARNING - INSTALLATION............23-173
WARNING - REMOVAL...............23-173
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - SERVICE WARNINGS........24-39
WARNING - WINDSHIELD SAFETY
PRECAUTIONS......................23-173
WARNING, BRAKES - BASE..............5-2
WARNING, CLUTCH.....................6-2
WARNING, FRONT......................2-7
WARNING, REAR......................2-16
WARNING, RESTRAINT SYSTEM.........8O-5
WARNING SYSTEM - DESCRIPTION,
CHIME..............................8B-1
WARNING SYSTEM - DIAGNOSIS AND
TESTING, CHIME......................8B-6
WARNING SYSTEM - OPERATION,
CHIME..............................8B-2
WARNINGS, GENERAL..............8W-01-7
WARNINGS, WARNING - SAFETY
PRECAUTIONS........................23-1
WARNINGS, WARNING - SERVICE.......24-39
WASHER FLUID INDICATOR -
DESCRIPTION.......................8J-35
WASHER FLUID INDICATOR -
DIAGNOSIS AND TESTING..............8J-36
WASHER FLUID INDICATOR -
OPERATION.........................8J-36
WASHER FLUID LEVEL SWITCH -
DESCRIPTION.......................8R-17
WASHER FLUID LEVEL SWITCH -
INSTALLATION......................8R-18
WASHER FLUID LEVEL SWITCH -
OPERATION.........................8R-17
WASHER FLUID LEVEL SWITCH -
REMOVAL..........................8R-17
WASHER HOSES/TUBES - DESCRIPTION,
FRONT.............................8R-10
WASHER HOSES/TUBES - DESCRIPTION,
REAR..............................8R-35
WASHER HOSES/TUBES - OPERATION,
FRONT.............................8R-10
WASHER HOSES/TUBES - OPERATION,
REAR..............................8R-36
WASHER NOZZLE - DESCRIPTION,
FRONT.............................8R-11
WASHER NOZZLE - DESCRIPTION, REAR . 8R-36
WASHER NOZZLE - INSTALLATION,
FRONT.............................8R-11
WASHER NOZZLE - INSTALLATION,
REAR..............................8R-37
WASHER NOZZLE - OPERATION, FRONT . . 8R-11
WASHER NOZZLE - OPERATION, REAR . . . 8R-36
WASHER NOZZLE - REMOVAL, FRONT....8R-11
WASHER NOZZLE - REMOVAL, REAR....8R-36
WASHER PUMP/MOTOR - DESCRIPTION . . 8R-18
WASHER PUMP/MOTOR - INSTALLATION . 8R-20
WASHER PUMP/MOTOR - OPERATION . . . 8R-19
WASHER PUMP/MOTOR - REMOVAL.....8R-19
WASHER RESERVOIR - DESCRIPTION....8R-21
WASHER RESERVOIR - INSTALLATION . . . 8R-22
WASHER RESERVOIR - OPERATION
......8R-21
WASHER RESERVOIR - REMOVAL
.......8R-21
WASHER SYSTEM - CLEANING, FRONT
WIPER
..............................8R-7
WASHER SYSTEM - CLEANING, REAR
WIPER
.............................8R-32
WASHER SYSTEM - DIAGNOSIS AND
TESTING, FRONT WIPER
...............8R-6WASHER SYSTEM - DIAGNOSIS AND
TESTING, REAR WIPER...............8R-30
WASHER SYSTEM - INSPECTION, FRONT
WIPER..............................8R-7
WASHER SYSTEM - INSPECTION, REAR
WIPER.............................8R-33
WATER DRAINAGE AND WIND NOISE
DIAGNOSIS, DIAGNOSIS AND TESTING . . 23-176
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-2
WATER PUMP - DESCRIPTION...........7-29
WATER PUMP - OPERATION.............7-30
WATERDAM - INSTALLATION....23-126,23-133
WATERDAM - REMOVAL........23-126,23-133
WATER-IN-FUEL INDICATOR -
DESCRIPTION.......................8J-37
WATER-IN-FUEL INDICATOR -
OPERATION.........................8J-37
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD......................22-8
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE.......................22-8
WEAR, STANDARD PROCEDURE -
MEASURING TIMING CHAIN.............9-71
WEATHERSTRIP - INSTALLATION, COWL . 23-185
WEATHERSTRIP - INSTALLATION, DOOR
LOWER...........................23-186
WEATHERSTRIP - INSTALLATION, DOOR
PRIMARY..........................23-185
WEATHERSTRIP - INSTALLATION,
SWING GATE BELTLINE...............23-186
WEATHERSTRIP - INSTALLATION,
SWING GATE OPENING...............23-186
WEATHERSTRIP - REMOVAL, COWL.....23-185
WEATHERSTRIP - REMOVAL, DOOR
LOWER...........................23-186
WEATHERSTRIP - REMOVAL, DOOR
PRIMARY..........................23-185
WEATHERSTRIP - REMOVAL, SWING
GATE BELTLINE.....................23-186
WEATHERSTRIP - REMOVAL, SWING
GATE OPENING.....................23-186
WEATHERSTRIP/RETAINER -
INSTALLATION, SIDE RAIL............23-186
WEATHERSTRIP/RETAINER -
INSTALLATION, WINDSHIELD A-PILLAR . . 23-187
WEATHERSTRIP/RETAINER - REMOVAL,
SIDE RAIL.........................23-186
WEATHERSTRIP/RETAINER - REMOVAL,
WINDSHIELD A-PILLAR...............23-186
WELD AND STRUCTURAL ADHESIVE
LOCATIONS - SPECIFICATIONS...........23-9
WHEEL - INSTALLATION, STEERING......19-12
WHEEL - REMOVAL, STEERING.........19-12
WHEEL ALIGNMENT - DESCRIPTION.......2-3
WHEEL ALIGNMENT - OPERATION.........2-3
WHEEL BALANCING - STANDARD
PROCEDURE.........................22-4
WHEEL CYLINDERS - ASSEMBLY.........5-29
WHEEL CYLINDERS - CLEANING.........5-28
WHEEL CYLINDERS - DISASSEMBLY......5-28
WHEEL CYLINDERS - INSPECTION........5-29
WHEEL CYLINDERS - INSTALLATION......5-29
WHEEL CYLINDERS - REMOVAL..........5-28
WHEEL MOUNTING - STANDARD
PROCEDURE........................22-10
WHEEL OPENING FLARE MOLDINGS -
INSTALLATION, FRONT...............23-145
WHEEL OPENING FLARE MOLDINGS -
INSTALLATION, REAR................23-145
WHEEL OPENING FLARE MOLDINGS -
REMOVAL, FRONT...................23-145
WHEEL OPENING FLARE MOLDINGS -
REMOVAL, REAR....................23-145
WHEEL REPLACEMENT - STANDARD
PROCEDURE........................22-10
WHEEL RUNOUT - DIAGNOSIS AND
TESTING, TIRES......................22-1
WHEEL SPEED SENSOR -
INSTALLATION, FRONT
.................5-34
WHEEL SPEED SENSOR -
INSTALLATION, REAR
..................5-35
WHEEL SPEED SENSOR - REMOVAL,
FRONT
..............................5-34
WHEEL SPEED SENSOR - REMOVAL,
REAR
...............................5-35
WHEELHOUSE SPLASH SHIELD -
INSTALLATION, FRONT
...............23-143
KJINDEX 29
Description Group-Page Description Group-Page Description Group-Page

JEEP LIBERTY 2002
SPARE WHEEL & HARDWARE19-020-<8)
21-522~
23 .lLI
11
b
RACK & PINION10
~66~ -
24I14~
~2~
!
31~J~L2S--£3J
!;:;q)17
118-#~ I~
12~
/~004-09516 ~~'"
5~132616A-15~~
1 Wheel, Spare 14Steel 5GL65S4AAA 160.00 16 004 09907Alloy --
16x7Code WLD 10 Arm, Upper Control AiL 52088632AA m #2.0 128.00To 10-1-01 5GL67PAKAA 249.00 #W/Steering Knuckle Assy Removed Deduct 1.2 004 09522 c~From 10-1-01 5GL67PAKAB 24900 11 Bum~r, Control Arm AiL 52088684AB m 25.75 -
Code WND 5GL66PAKAB 260'00 12 Knuckle Assy, Steering R 52088652AA m #1.7 127.0017x7.5 .L 52088653AA m #1.7 127.00 1 Gear Assy, SteeringCode WGO 5HW90ZDRM 249.00 #/ncludes R&R Brake Rotor and Hub & Bearing Assy, 2.4L Eng 52128588M m #1.9 484.00Code WGR 5HW90AFMAA 24900 R&R Both Sides 3.2 37L Eng 52128518M m #1.9 459.002 Jack 52059104 83:35 13 Joint, Lower Balll] AiL 5069161AB m 2.0 27.50 #W/4WD Add 3.63 Wrench, Lug 52059478AA 12.85" l]/nc/uded w/Steering Knuckle Assy 2 Boot, Steering Gear1J AiL 5O72446M m 57.104 Bracket, Jack 52059369M 16.35!114Arm,LowerControl R 52088636AD m#2.2 117.00 3Bolt,Mountingl] AiL 6506517M 7.505 Label, Jack Instructions-See InforrnatJon Labels SectJon L 52088637AD m #2.2 117.00 4 Nut, MountJng:~ AiL 6504707 2.456 Bracke~ Spare. Wheel 55155933AB 59.10 #Includes R&R Bushings, w/Steering Knuckle 5 Bushing, Steering Gear1J AiL 52038783AB 15.20Cover, :opare Tire 5JG141X7M Removed Deduct.9 l1/nc/uded w/Steering Gear AssyAiL 52088746M m 12.25 6 Rod, Outer Tie R 5O72444M 46.70AiL 52088649AC m L 5072445M 46.70
AIL 6507080AA18 Bolt, Lower Carn (2/Side) AiL 6507321M19 Nut, Absorber AiL 6506443M 1.5020 Retainer, Absorber AiL 52089069M 2.25 2.4L ENG21 Mount, Absorber R 52128532AA m #1.8 91.70L 52128533AA m #1.8 91.7022 Isolator, Upper Spring AiL 52088686M m #1.8 16.25 423 Springl] AiL 52088625M m #1.8 35.75~.tr24 Absorber, Shock11 AiL 52088650AB m #1.8 36.95 111Additional Parts &lor Dealer Contact Required 0 3125 Isolator, Lower Spring AiL 52088686M m #1.8 16.25 -
I #R&R One Side Complete, Includes R&R ClevisAbsorber, w/Steering Knuckle Assy Removed Deducr ~.7, R&R Both Sides 3.426 Clevis, Absorber AiL 52088748AC m #.6 49.75#W/Steering Knuckle Assy Removed Deduct.4
29\",~~-l 004-09908
27 Retainer, Stab Bar AiL 52088631M m #.3 9.70 I128 Bushing, Slab Bar AiL 52088778M m #.3 4.60 c 004 09909#R&R One Side Complete, Not Included in O/H! -
29 Link, Stab Bar Ail 52088662AB m #.3 43.75PS.#Not Included in O/H 1 ump, teerlng30 Bar, Stabilizer 52088660M m #.8 98.25 2 Pulley, ~ump#Includes R&R Stab Bar Links, Bushings & Retainers 3 Reservoir, Pu~pNot Included in O/H 4 Cap, Reservoir.Bracket, Reservoir
6
~",,3
2
m .3m .3
52
Use Procedure Explanation 11 with the following text.
R&I Suspension/Sub.Frame Assy2WD m#2.74 WD m #3.6#Not Included in O/H SuspensionO/H SuspensionOne Side , R/Lm 4.7Both Sides. m 8.4Bleed Brake Systemw/ABS m .6w/oABS m .3AdjustFrontAlignment m 1.5NOTE 1: R&UR&R or O/H Does Not include alignment or bleedbrake system.
NOTE 2: All Parts in this section are included in overhaulunless noted otherwise.
/1
I'~~II::It
52088711AA m 1.7 130.0053031722AA m 21.6052088713AA m .5 40.2552128513AA 10.4552088874AD 43.4552088722AC m .8 163.0052088718AC m 23.4552128561AA m .9 174.00
5
~L-7 Cooler, SteeringR&I Axle Housing Assy m 3.0R&I Outer Axle Shaft Assy R/Lm #1.5#WlSteering Knuckle Assy Removed Deduct .93.7L ENG
4004-09906
004-09520
1 Nut, Axle AiL 6506454AA m 8.502 Rotor, Brake AiL 52128247AA m #.9 104.00#R&R Both Sides 1.63 Caliper, Brake R 5066422AA m #.5 182.00 IL 5066423AA m #.5 182.00 I4 Bracket, Caliper Mounting AIL 5019986AA m #.5 42.50#R&R One Side Complete, w/Brake Rotor RemovedDeduct .3, R&R Both Sides .85 Pad Set, Brake 5066427AA m #1.0 128.00#Deduct .5 for Each Brake Caliper Removed6 Hub & Bearingw/ABS R 52128692AA m #1.3 259.00L 52128693AA m #1.3 259.00w/o ABS AiL 52128352AB m #1.3 259.00I#Includes R&R Brake Rotor, R&R Both Sides 2.47 Stud, Wheel AiL 6O36388AA m 2.958 Sensor, Front ABS-See ABSIBrakes Section9 Hose, Front Brake R 52128312AA m #.3 18.35L 52128311AA m #.3 18.35#W/Caliper Removed Deduct .2
567Procedure Explanation Pages Must Be Used with the Above Text for an Accura'~ Damage Report.Comments or suggestions? Need assistance? Call 1-800-854-7030 or 858/578-6550, Ext 8220. Fax 1-888-256-7969 or 858/549-0629.CH
R&I Steering Gear Assy m #1.7#W/4WD Add 3.6
NOTE: R&R Does Not include adjust wheel alignment.~
6~9 2
67rl1
~'~
3 2,
51 Shaft Assy, Outer Axle f IA
~,::;~~~~2.4LEng R 5066022AA m#1.5 994.00cJ1y L 5066023AA m #1.5 1155.00'
3.7L Eng R 5066020AA m #1.5 1020.00L 5066021AA m #1.5 1155.00#WlSteering Knuckle Assy Removed Deduct .92 Boot Kit, Inner1j AiL 5066024AA m 26 203 Boot Kit, Outer1j AiL 5066025AA m 25:50~/ncluded w/Outer Axle Shaft Assy 004-09524
Bracket, Mountin~2.4L Eng R 52059472AB m 81.85 1 PumplReservoir. Assy, Steering 52088710AA m 2.4 130.00L 52059473AB m 54.50 2 Cap, Reservolr1j 52088956AA 27.453.7L Eng R 52059464AB m 81.85 ~/ncluded w/Steering Pumf)/ReseIVo;r AssyL 52059465AB m 30.85 I 3 Pulley, Pump 5:3010258AC m #.3 20.25

JEEP LIBERTY 2002
QUARTER GLASS Conf'd410
OjJ.::::::::~~~~::::::::::;;;')t';
0.000.000.000.00
,...,.,,-
Privacyw/Antenna A 55360056AB #1.5L 55235923AB #1.5w/o Antenna A 55235922AB #1.5L 55235923AB #1.5NAGSTintedw/Antenna A DQO9990GTN #1.5 0.00L DQO9989GTN #1.5 302.751w/o Antenna AIL DO09988-9GTN #1.5 302.75Privacyw/Antenna A DO10069YPN #1.5 270.85L DQ10068YPN #1.5 297.95w/o Antenna AIL DO10067-8YPN #1.5 297.95#Includes Clean Up Old Adhesive as Necessary2 Spacer, Glass (4) 55360509M .35
32~
3~4~004-09943
55156554M55156275AB55156405M55156277M
Decal, Aear Gate1 "Jeep""3.7L""CAD"4 "Up Country"Use Procedure Explanations 25 and 28 with the fol/owing text.
R&IGlassAssy 3~
R&I Trim Panel ~~~~
~ '
.2~2 3
1\11 ..1-1[1\1
4~ '--004-09573-J2~
j~
.2 22.85 2 004-09575.2 13.101.2 25.45 1 Drum, Brake Ail 52128270AA m '.3 85.00.2 11.00 #R&R Both Sides.52 Shoe Set, Brake 5O66147AA m 11.4 108.00#Includes R&R Brake Drums3 Plate, Backing R 5066150AA m #.3 30.45l 506615tAA m #.3 30.45#W/Axle Shaft Assy Removed4 Shaft Assy, Axle R 5066484AA m.7 294.00l 5O66485AA m.7 295.005 Studl Wheell1 (5/Side) Ail 5016496AA m 1.2516 Retainer, Axle~ Ail 5O66486AA m'1.1 9.007 Seal, Axle~ Ail 5O12824AA m'1.1 3.458 Bearing, Axle1[ Ail 5012825AA m #1.1 56.509 Retainer, Beann9~ Ail 5O72894AA m #1.1 12.25~Included w/Axle Shaft Assy#R&R One Side Com~lefeSensor, Rear ABS-See ABS7Brakes Section10 Housing Assy, AxIe1] 5O66495AB m #5,0 1485.00~Additional Parts &/or Dealer Contact RequiredHousing, Axle (a) 5O66477AA m 17.7 817.00(a) Included w/Axle Housing Assy#Includes R&R Axle Shafts Assemblies
1 GlassChrYslerTinted 55360340AB.6 458.00Pnvacy 55360342AB650000NAGS ..
Tinted DBO9991GTY.6 1042.75 004-09572Pnvacy DBO9991YPY.6 1177301.Solar DB10070YPY.6 1177:30 1 Panel,RearGaIeTrlm~2 Hinge, Glass R 55360216AB #.4 23.95 wlStorage NetL 55360217AB #.4 23.95 Slate Gray#R&R Both Sides .5, Included in R&R Glass Taupe3 Stay, Glass AiL 55360171AA 2 3135 wlo Storage Net4 Striker, Glass 55360220AA #:2 21:50 Slate Gray#Included in R&R Glass Taupe
SHE6S)(DVACSHE6S\'lL5AC
SGE69;(DVACSGE69"lL5AC
.2 220.00.2 220.00
.2 125.00.2 125.00
#.1 20.4555360309M#WlTrim Panel Removed17111
WIPER SYSTI:MUse Procedure Explanations 25 and 28 with the fol/owing text.
SHEET METAUHARDWAREr10
1--17.l1
19-f1 ~21
~ E:-22 24
23~ ~~~
~~:==~~Y~::C:;==::~~O9576
11 Arm Assy, Upper Control 52088901AB m .8 212.0012 Joint, Ball~ 52088647M m #.3 50.0013 Bushing, Control Arm~ AiL 52086425 m #.2 11.95#W/Upper Control Arm Assy Removed.1 16.60 14 Bracket, Ball Join~ 52088894M m 56.25#.2 20.45 15 Bolt, Bracke~ 6503610 2.2016 Nu1, Bo~ 6503711 1'.451.60 ~/ncluded wlUpper Control Ann Assy4.95 17 Bolt, No.1 Mounting AiL 6504748 3.851.60 18 Bolt, No.2 Mounting (3) 6505445M 2.455.50 19 Absorber, Shock AiL 52088673AB m #.4 0.005.60 #R&R Both Sides .6, wlCoil Spring Removed Deduct .37.75 20 Isolator, Upper Spring AiL 52088707AA m 7.85#.3 125.00 1 Bumper, Ul?per AiL 52088705AB m 16.602 Spring, ColI'l AiL 52088695AB m #.6 54.95#.2 7.95 1jAdditlonal Palts &/or Dealer Contact Required#R&R Both Sides 1.0AiL 52128524M m 17.95AiL 52088682AB m #.6 102.00#WIAxle Housing Removed Deduct .325 Bar, Stabilizer 52088677AB m .5 127.00
~~~ "I fJ-s
9
~
Refinish Rear Gate Panel Outside 2.0Add for Jambs & Interior 1.0RefinishUpperGateHinge .2Refinish Lower Gate Hinge .2R&I Rear Gale Assy #1.4#Includes R&VR&R Left Qualter Trim PanelR&I Outside Handle #.4#Includes R&I Trim PanelR&ISpareTireBracket .2
7 56 I 8
l.s~-10 m'-
I004-09574 ---
1 Blade, Wiper 5066964AA2 Arm, Wiper 5066965AA#Includes R&R Wiper Blade3 Cover, Wiper Arm 550766504 Nut, Wiper Arm 65001655 Cover, Motor 550766506 Nut, Motor 65022637 Bezel, Motor 55155B87AA8 Stop, Wiper 5515~~86AA9 Motor, Wiper 55155e:84AA#w!rrim Panel Removed10 Nozzle, Washer 55156158AA#Included in R&R Roof Panel
4WD
4
-~~_~~~7~"'- --~3~ 1 ~~ 004-09570
1 Panel, Rear Gate 55176934AC #4.0 375.00#Includes R&VR&R Left Qualter Trim Panel2 Hinge, GateUpper 52850558AA #.2Lower 52850559AA #.2#WlRear Gate Assy RemovedCheck, Gate 55360170AA #.2 38.8513 Latch, Glass 55360357 AA #.2 70.85 Use Procedure Explanation 23 with the following text.Latch, Gate 55360359AA #.2 55.754 Handle, Outside 55360331AC #.35 Weatherstrip, Upper Gate 55360065AA #.2 -14.10 I#Wnrim Panel Removed6 Sta.bilizer, Gate 55360324AC 6.20 l R&I Suspension/Axle Assy .m 3.07Stnker 55176954AA.2 12.60~ Check Rear Alignment .m .88 Spacer, Striker 5507548.3 1.50, Add to Adjustrront Alignment9Bracket,SpareWheel-SeeWheelSecllon 2WD m .710 Weatherstrip, Rear 55716958AA .2 0.00 4WD m 1.0Bleed Brake Systemwi ABS m .6w/oABS m .3
NOTE: R&I/R&R Does Not include illignment or bleed brakesystem
Illustration Located in Next Column
1 Drum, Brake AIL 52128270AA m #.3 85.00#R&R Both Sides .52 Shoe Set, Brake 5066147AA m #1.4 108.00#Includes R&R Brake Drums3 Plate, Backing R 5066150AA m #.3 30.45L 5066151AA m #.3 30.45#W/Axle Shaft Assy Removed
labor Times Shown are for Replacement with New OEM Undamaged Parts on New Undamaged Vehicles.Comments or suggestions? Need assistance? Call1-80D-854-7030 or 8!i8/578-6550, Ex1 8220. Fax 1-888-256-7969 or 858/549-0629.576CH