2002 ISUZU AXIOM battery

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±105
Chart A: Does Not work At All
StepActionValue(s)Ye sNo
11. Turn on the ignition switch (the engine is run).
2. Disconnect the mix actuator connector (C±43).
3. Short-circuit the chassis harness side connector
terminal No.C43±3 and No.C43±7.
4. Using the temperature control switch, select 18
C
(65
F) for the temperature.
Is the battery voltage applied on a regular interval basis
between the harness side connector terminal
No.C43±6 (-) and No.C43±8 (+)?
ÐGo to Step 3Go to Step 2
2Replace the auto air conditioner control unit.
ÐVarify repairÐ
3Using the temperature control switch, select 32
C
(90
F) for the temperature.
Is the battery voltage applied on a regular interval basis
between the harness side connector terminal
No.C43±6 (+) and No.C43±8 (-)?
ÐGo to Step 5Go to Step 4
4Replace the auto air conditioner control unit.
ÐVerify repairÐ
5Is there continuity between the harness side connector
terminal No.I19±6 and No.C43±6?
ÐGo to Step 7Go to Step 6
6Repair an open circuit between terminal No.I19±6 and
No.C43±6.
Is the action complete?
ÐGo to Step 5Ð
7
Is there continuity between the harness side connector
terminal No.I19±5 and No.C43±8?
ÐGo to Step 9Go to Step 8
8Repair an open circuit between terminal No.I19±5 and
No.C43±8.
Is the action complete?
ÐVerify repairÐ
9Replace the mix actuator.
Is the action complete?
ÐVerify repairÐ

1A±108
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
Chart A: Does Not Work At All
StepActionValue(s)Ye sNo
11. Turn on the ignition switch (the engine is run).
2. Disconnect the mode actuator connector (C±42)
3. Select VENT pressing the mode actuator.
Is the battery voltage provided on a regular interval
between the harness side connector terminal
No.C42±1 (+) and No.C42±5 (-)?
ÐGo to Step 3Go to Step 2
2Replace the auto air conditioner control unit.
Is the action complete?
ÐVarify repairÐ
3Turn on the DEF mode switch.
Is the battery voltage provided on a regular interval
between the chassis side connector terminal
No.C42±5 (+) and No.C42±1 (-)?
ÐGo to Step 5Go to Step 4
4Replace the auto air conditioner control unit.
ÐVarify repairÐ
5Is there continuity between the harness side connector
terminal No.C42±1 and No.I19±4?
ÐGo to Step 7Go to Step 6
6Repair an open circuit between terminal No.C42±1 and
No.I19±4.
Is the action complete?
ÐGo to Step 5Ð
7Is there continuity between the harness side connector
terminal No.C42±5 and No.I19±3?
ÐGo to Step 9Go to Step 8
8Repair an open circuit between terminal No.C42±5 and
No.I19±3.
Is the action complete?
ÐVerify repairÐ
9Replace the mode actuator.
ÐVerify repairÐ

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±111
ConditionPossible causeCorrection
The fan dose not rotate at allÐRefer to Chart A
The fan dose not rotate in the
MAX±HI modeÐRefer to Chart B
The fan dose not rotate in any mode
other than MAX±HIÐRefer to Chart C
The fan dose not stopÐRefer to Chart D
Chart A: Fan Does Not Rotate At All
StepActionValue(s)Ye sNo
1Are the fuse No.F±5, F±6 and No.F±7 normal?
ÐGo to Step 2
Replace the
fuse
2Are the relay No.X±1 and No.C±35 normal?
ÐGo to Step 3
Replace the
relay
3Turn on the ignition switch (the engine is run).
Is the battery voltage applied between the harness side
connector terminal No.C36±1 and ground?
ÐGo to Step 5Go to Step 4
4Repair an open circuit between terminal No.C36±1 and
No.F±5 and F±6 fuse.
Is the action complete?
ÐGo to Step 3Ð
5Is there continuity between the harness side connector
terminal No.C36±2 and ground (No.C±10)?
ÐGo to Step 7Go to Step 6
6Repair an open circuit between terminal No.C36±2 and
ground.
Is the action complete?
ÐÐÐ
7Is the battery voltage applied between the harness side
connector terminal No.C36±2 and No.C36±1?
ÐGo to Step 8Go to Step 9
8Replace the blower motor.
Is the action complete?
ÐVerify repairÐ
9Refer to chart B and C.
Is the action complete?
ÐVerify repairÐ

1A±112
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
Chart B: Fan Does Not Rotate in MAX HI Mode
StepActionValue(s)Ye sNo
1Is the MAX-HI relay (C±35) normal?
ÐGo to Step 2
Replace the
relay
21. Turn on the ignition switch (the engine is run).
2. Set the fan switch to the MAX-HI.
Is there continuity between the harness side connector
terminal No.C36±2 and No.C35±5?
ÐGo to Step 4Go to Step 3
3Repair an open circuit between terminal No.C36±2 and
No.C35±5.
Is the action complete?
ÐGo to Step 3Ð
4Is there continuity between the harness side connector
terminal No.C35±1 and ground (No.C±10)?
ÐGo to Step 6Go to Step 5
5Repair an open circuit between terminal No.C35±1 and
ground (No.C±10).
Is the action complete?
ÐGo to Step 4Ð
6Is the battery voltage applied between the harness side
connector terminal No.C35±2 and ground?
ÐGo to Step 8Go to Step 7
7Repair an open circuit between terminal No.C35±2 and
No.F±7 fuse.
Is the action complete?
ÐGo to Step 6Ð
8Is the battery voltage applied between the harness side
connector terminal No.I19±2 and ground?
ÐGo to Step 10Go to Step 9
9Repair an open circuit between terminal No.C35±4 and
No.I19±2.
Is the action complete?
ÐVerify repairÐ
10Replace the auto air conditioner control unit.
Is the action complete?
ÐVerify repairÐ

1A±116
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
ConditionPossible causeCorrection
Magnetic clutch does not workÐRefer to Chart A
Chart A: Magnetic Clutch Does Not work
StepActionValue(s)Ye sNo
1Is the fuse No.F±7 normal?
ÐGo to Step 2
Replace the
fuse
2Is the relay No.X±2 (compressor relay) No.X±8 (A/C
thermo relay) and No.X±1 (heater relay) normal?
ÐGo to Step 3
Replace the
relay
3Is there continuity between the pressure switch side
connector terminal No.C21±1 and No.C21±2?
ÐGo to Step 5Go to Step 4
4Pressure switch defective or refrigerant pressure
improper.
Pressure switch replaced or refrigerant pressure
adjusted?
ÐGo to Step 3Ð
51. Turn the ignition switch on. (the engine is run.)
2. Turn the air conditioner switch on.
Is the battery voltage applied between the harness side
connector terminal No.E2±1 and the ground?
ÐGo to Step 7Go to Step 6
6Magnetic clutch defective or earth defective.
Magnetic clutch replaced or earth replaced?
ÐGo to Step 5Ð
7Is there continuity between the harness side connector
terminal No.X2±1 and No.E2±1?
ÐGo to Step 9Go to Step 8
8Repair an open circuit between terminal No.X2±1 and
No.E2±1.
Is the action complete?
ÐGo to Step 7Ð
9Is the battery voltage applied between the harness side
connector terminal No.X2±5 and ground, No.X2±2 and
ground?
ÐGo to Step 11Go to Step 10
10Repair an open circuit between terminal No.X2±5 and
fuse No.F±7, No.X2±2 and fuse No.F±7.
Is the action complete?
ÐGo to Step 9Ð
11Is the battery voltage applied between the harness side
connector terminal No.I20±18 and ground?
ÐGo to Step 13Go to Step 12
12Repair an open circuit between terminal No.I20±18 and
No.X2±4.
Is the action complete?
ÐGo to Step 11Ð
13Is the battery voltage applied between the harness side
connector terminal No.C21±2 and ground?
ÐGo to Step 15Go to Step 14
14Repair an open circuit between terminal No.C21±2 and
fuse No.F±7.
Is the action complete?
ÐGo to Step 13Ð
15Is the battery voltage applied between the harness side
connector terminal No.X8±5 and ground, No.X8±2 and
ground?
ÐGo to Step 17Go to Step 16
16Repair an open circuit between terminal No.X8±5 and
No.C21±1, No.X8±2 and fuse No.F±7.
Is the action complete?
ÐGo to Step 15Ð

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±117
Chart A: Magnetic Clutch Does Not work (Cont'd)
StepNo Ye s Value(s) Action
17Is the battery voltage applied between the harness side
connector terminal No.I19±14 and ground?
ÐGo to Step 19Go to Step 18
18Repair an open circuit between terminal No.X8±3 and
I19±14.
Is the action complete?
ÐGo to Step 17Ð
19Is there continuity between the harness side connector
terminal No.X8±1 and PCM (F45)?
ÐGo to Step 21Go to Step 20
20Repair an open circuit between terminal No.X8±1 and
PCM (F45).
Is the action complete?
ÐGo to Step 19Ð
21Is there continuity between the harness side connector
terminal No.X2±4 and PCM (F4)?
ÐGo to Step 23Go to Step 22
22Repair on open circuit between terminal No.X2±4 and
PCM (F4).
Is the action complete?
ÐGo to Step 21Ð
23Is there continuity between the harness side connector
terminal No.I20±4 and ground?
ÐGo to Step 25Go to Step 24
24Repair an open circuit between terminal No.I20±4 and
PCM (S47).
Is the action complete?
ÐGo to Step 23Ð
251. Connect the connector of PCM.
2. Connect the connector terminal No.I19±14 which is
on the harness side on the auto air conditioner
control unit.
Magnetic clutch works?
Ð
Replace the
auto air
conditioner
control unit
Replace the
PCM
CAUTION: T h e r e a r e conditions which air
conditioner system dose not operate except trouble
as follows.
1. The throttle is griater than 90%.
2. The ignition voltage is below 10.5 volts.
3. The engine speed greater than 4500 RPM for 5
seconds or 5400 RPM.
4. The engine coolant temperature (ECT) is greater
than 125
C (257
F).
5. The intake air temperature (IAT) is less than 5
C
(41
F).
6. The power steering pressure switch signals a
high pressure condition.

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±119
Power Transistor
1. Remove the power transistor connector (C±34) from
the evaporator assembly.
2. Check the conduction between the power transistor
side terminals.
C01R200006
MAX HI Relay
1. Remove the MAX ± HI relay connector (C±35) from
the blower assembly.
2. Check the conduction between the MAX ± HI relay
side terminals.
C01R200011
In Car Sensor
1. Turn on the ignition switch (the engine is started).
Start the air conditioner in ªAutoº.
2. Make sure that the in car sensor suctions cigarette
smokes and such.
In Car Sensor
1. Dismount the in car sensor from the automatic
heater/air conditioner control unit. Connect (+) end
and (±) end of the battery to the aspirator motor side
terminals No.I17±1 and No.I17±2, respectively, then
check if the motor runs normally.
C01R200010

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±121
On-Vehicle Service
Power Transistor
874R200014
Legend
(1) Glove Box
(2) MAX HI Relay
(3) Power Transistor Connector
(4) Power Transistor
Removal
1. Remove the glove box.
2. Remove the MAX±HI relay.
3. Disconnect the power transistor connector.
4. Remove the power transistor.
Installation
To install, follow the removal step in the reverse order.
Automatic Heater/Air Conditioner
Control Unit
865R200007
Legend
(1) Display
(2) Audio & Switch Assembly
(3) Automatic Air Conditioner Control Unit
(4) Knee Pad (RH)
(5) Center Cluster
(6) Center Cluster Upper
(7) Knee Pad (LH)
Removal
1. Disconnect the battery ground cable.
2. Remove the knee pad (R/LH).
3. Remove the center cluster upper.
4. Remove the center cluster.

Refer to
Instrument Panel Assembly in Body
Stractur section.
5. Disconnnect the six connectors.
6. Remove the automatic air conditioner control unit.
Installation
To install, follow the removal step in the reverse order.