2002 HONDA PASSPORT check engine

212Care and Maintenance
Change the oil and oil filter every
3,750 miles (6,000 kilometers) or
every three months if you drive
under one or more of these
“severe driving” conditions:
•Driving in dusty areas
•Towing a trailer
•Frequent idling or idling for
long periods
•Frequent short trips (4 miles [6
kilometers] or less) in cold or
freezing weather, where the
engine does not thoroughly
warm up.
•Change the oil and oil filter as
soon as possible after driving in
a dust storm.
Oil Change
Changing the oil and filter requires
special tools and access from
underneath the vehicle. The vehicle
should be raised on a service
station-type hydraulic lift for this
service. Unless you have the
knowledge and proper equipment,
you should have this maintenance
done by a skilled mechanic.
1. Warm up the engine. This
makes the oil drain faster and
more thoroughly.
2. Remove the oil filler cap.
3. Remove the drain plug and drain oil fully.
4. Install the drain plug, with a new gasket, and tighten it.
5. Fill the engine with the proper amount of new oil (see
“Specifications”). Oil Filter Installation
1. Remove the old oil filter with
the filter wrench.
2. Apply a light coat of engine oil to the oil filter gasket.
3. Hand-tighten the filter until the gasket contacts the sealing
face.
4. Using the filter wrench, tighten the filter one full turn.
5. Run the engine and inspect for leaks.
6. Shut off the engine. After a couple of minutes, check the
oil level. If necessary, add oil
to bring it to the
FULL mark.

An improperly installed oil filter
can result in severe engine
damage.

213Care and Maintenance
Oil Viscosity
Engine oil viscosity (thickness) has
an effect on fuel economy. Lower
viscosity engine oils can provide
increased fuel economy; however,
higher temperature weather
conditions require higher viscosity
engine oils for satisfactory
lubrication. To get the best fuel
economy with your vehicle, you
should use a fuel-saving engine oil
of the proper viscosity. These oils
can be found in service stations andother retail stores. They are
identified by words such as
“Energy Saving,” “Conserves
Gasoline,” “Gas Saving,”
“Gasoline Saving,” “Friction
Reducing,” “Improved Gasoline
Mileage” or “Fuel Saving.”
The chart lists the recommended
engine oil viscosities for the
temperature range you expect
before the next oil change. For
temperatures above 0

F (–18
C),
SAE 10W–30 is the preferred viscosity grade. If cold-weather
starting problems are encountered
at temperatures below 0

F
(–18
C), SAE 5W–30 viscosity
oils may be required.
Oil Level Check
It is the owner ’s responsibility to
keep the engine oil at the proper
level. Check the oil level at regular
intervals (such as every other fuel
stop) and keep it above the
“minimum” level mark.
Remember, your engine may use
more oil when it is new.
The best time to check the engine
oil level is when the oil is warm,
such as during a fuel stop. Shut off
the engine and wait about 5 minutes
for the oil to drain back to the oil
pan. Pull out the dipstick, wipe it
clean, and push it back down all the
way. Now pull out the dipstick and
–20 F 0 F
– 30 C –20 C –10 C 20 F
40 F
0 C 10 C 20 C
60 F
80 F
30 C 40 C
100 F
TEMPERATURE RANGE YOU EXPECT BEFORE NEXT OIL CHANGE
VISCOSITY GRADE – AMBIENT TEMPERATURE
SAE 5W–30
SAE 10W–30, PREFERRED
SAE 15W–40, 20W–40, 20W–50

214Care and Maintenance
look at the oil level on the dipstick.
The dipstick has two markings
which indicate the minimum and
maximum allowable oil level. If the
oil level is lower than the marked
area, it indicates the need for
additional oil. Push the dipstick
back down all the way after taking
the reading.
•If you check the oil level when
the oil is cold, do not run the
engine first. The cold oil will
not drain into the pan fast
enough to give a true reading.
Engine Oil Additives
There are many extra engine oil
additives for sale. Your engine
should not need these extra
additives if you use recommended
quality engine oil and change it as
suggested. If you think your
engine has an oil-related problem,
talk to your Honda dealer.
See your Maintenance Schedule for
change intervals. If the vehicle is
operated in dusty areas it will
require more frequent element
replacement. Your Honda dealer
can be of assistance in determining
the proper replacement frequency
for the conditions under which you
operate your vehicle.
Do not attempt to clean the air
filter. The filter is designed to
provide normal filtering
efficiency between replacement
intervals.
For maximum protection, it is
advisable to use genuine Honda air
cleaner filters as replacements.
Air Cleaner Filter

215Care and Maintenance
Never run the engine with the air
cleaner filter removed. If the
engine should backfire, it could
possibly cause an engine
compartment fire.
Be sure to reinstall the air cleaner
filter and assembly correctly. If it
is installed incorrectly, engine
damage could result.
See the Maintenance Schedule to
find out how often the lubricant
level should be checked.
Check that the fluid level reaches
the plug hole by removing the
filler plug on the transmission and
transfer case. If the fluid level is
low, refill the case up to the filler
plug hole.
Use a high-quality engine oil
labeled SG or SF that is of the
correct viscosity for existing
ambient temperatures as follows.
Ambient
TemperatureViscosity
Lubricant
to Be Used
Areas where
ambient
temperatures of
90
F (32
C) and
higher are regularly
encountered.
SAE 15W-40 20W-40
20W-50
Other areasSAE 5W-30
(2WD)
OIL FILL PLUG
DRAIN PLUG
(4WD)
OIL FILL PLUG
DRAIN PLUG
RIGHT SIDE
LEFT SIDE
Manual Transmission Fluid

216Care and Maintenance
Proper Fluid
Kind of Fluid
TransmissionDEXRON III
Transfer
(4WD)SAE 5W-30
(Engine oil)
Have the fluid level in the
automatic transmission checked
during the regularly scheduled
maintenance at your Honda
dealer.
If you suspect an automatic
transmission fluid leak, take the
vehicle to your Honda dealer for
inspection and repair.
Transmission damage could result
if you let the fluid level get too
low.
Drain Intervals
The automatic transmission drain
interval is not time or mileage
dependent. It will vary according
to your driving habits and vehicle
usage.
Your dealer will check the
transmission fluid’s condition and
life expectancy during regularly
scheduled maintenance, and
inform you at what mileage it
should be changed. See the Maintenance Schedule
List to determine how often the
lubricant should be changed. Add
lubricant, if needed, by filling to
the level of the filler plug hole.
Use
GL-5 gear lubricant of the
proper viscosity as shown in the
chart.
If your vehicle is equipped with
the optional limited slip
differential (on the rear axle), use
GL-5 Limited Slip Differential
Gear Lubricant together with
Limited Slip Differential Gear
Lubricant Additive (Part No.
8-01052-358-0) or equivalent.
Use the correct viscosity for the
existing ambient temperatures.
Automatic Transmission FluidFront (4WD)
and Rear Axles

217Care and Maintenance
Recommended Lubricant
Ambient
TemperatureLubricant Viscosity to Be Used
Rear
AxleFront Axle
Below 50
F(10
C)
SAE 80
or SAE80W-90
SAE
75W-90
synthetic
0
F to 90h
F(–18
C to
32
C)
SAE 90
or SAE
80W-90
SAE
75W-90
synthetic
Above 50
F(10
C)
consistentlySAE
140SAE
80W-90
or SAE
80W
-140
The engine cooling system is
designed to maintain the engine at
the proper operating temperatures.
The cooling system was filled at
the factory with a quality engine
coolant. The engine cooling system
is designed to use coolant (a
mixture of water and ethylene
glycol antifreeze) rather than plain
water. The engine coolant solution
should be used year-round. It has
many advantages such as:
•provides freezing protection as
low as –33
F (–36
C)
• provides boiling protection up
to 262
F (128
C)
•protects against rust and
corrosion in the cooling system
• maintains the proper engine
temperature for efficient
operation and emission control
•allows proper operation of the
engine coolant temperature gauge See the Maintenance Schedule in
this section to find out when the
engine coolant must be replaced.
Checking the Coolant Level
Check the engine coolant level at
the interval shown in the
Maintenance Schedule unless there
is evidence of leaking or
overheating. The engine coolant
level should be between the
maximum and the minimum level
marks on the radiator reserve tank.
Engine Cooling System

218Care and Maintenance
You usually do not need to remove
the radiator cap to check the engine
coolant level.
Removing the radiator cap
while the engine is hot can
cause the coolant to spray
out, seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.
Adding Engine Coolant
To add engine coolant, remove the
cap on the radiator reserve tank
and fill the tank up to the
maximum level mark. Add a
50/50 mixture of water and a good
quality ethylene glycol antifreeze.
If you need to add engine coolant
frequently, see your Honda dealer
for a cooling system check.
If the proper quality antifreeze
is used, there is no need to add
extra inhibitors or additives. They
may be harmful to the proper
operation of the system.
Cooling System Service
The cooling system should be
serviced at the intervals specified
in the Maintenance Schedule as
follows:
•Wash the radiator cap and filler
neck with clean water.
•Check the engine coolant level
in the radiator and have it tested
for freeze protection. Add
ethylene glycol antifreeze, if
needed, to maintain freeze
protection at
–33
F ( –36
C).
•Have the cooling system and
radiator cap tested for a
pressure capacity of 15 psi (105
kPa). If a replacement cap is
needed, use a cap specified for
your model.
•Tighten all radiator and heater
hose clamps and inspect all
hoses. Replace the hoses if they
are swollen, “checked, ” or
otherwise worn. Carefully
tighten the hose clamps at the
radiator. Overtightening could
bend or collapse the radiator
fittings.
•Clean the front of the radiator
core and air conditioning
condenser.
It is the owner ’s responsibility to:
•Maintain the cooling system
freeze protection at –33
F

219Care and Maintenance
(–36

C) to ensure protection
against corrosion and loss of
engine coolant from boiling.
This should be done even if
freezing temperatures are not
expected.
•Add ethylene glycol-based
antifreeze when antifreeze has
to be added because of engine
coolant loss or if more
protection against freezing at
temperatures lower than –33
F
(–36
C) is needed. Do not use
an alcohol-based or
methanol-based antifreeze, or
plain water. They boil at a
lower point, and do not provide
corrosion protection.
Thermostat
The engine coolant temperature is
controlled by a thermostat, which
stops engine coolant flow through
the radiator until a preset
temperature is reached. This
thermostat is installed in the
engine coolant inlet on the front
of the engine block. The same
thermostat is used in both winter
and summer.Brake Master Cylinder
Check the master cylinder fluid
level in the reservoir every time
you check the engine oil level.
The level should be between the
MAX and ADD level line. If the
level is lower than the
ADD level
line, fill to the
MAX level line
with
DOT-3 or DOT-4 fluid.
Other Required
Maintenance