2002 HONDA PASSPORT reset

108Interior Features
The
LOCK button on the driver
’s
door panel removes power from
the passengers’ windows. Only
the driver ’s window can be raised
and lowered.
PASSENGERS’
WINDOW LOCK
OFF ON
Checking the Circuit Breaker
In the event the power windows
do not operate, check the circuit
breaker.
•To reset the circuit breaker, first
turn the ignition switch off, and
then push the knob on the circuit
breaker. The windows should
now operate.
•If the circuit breaker
immediately goes off again or
the windows do not operate,
have the electrical system
checked by a dealer as soon as
possible.
Operation
The tailgate has a hatch glass and
a door. The hatch glass must be
raised before opening the door.
To open the hatch glass, push in
on the button on the tailgate door.
If the tailgate is locked, first
unlock the tailgate with the power
door locks or by using the key in
the outside tailgate lock. Make
sure the rear window wiper is off
and in its parked position before
opening the hatch glass.
Lock
Unlock
Tailgate

125Comfort and Convenience Features
AM/FM/Cassette Stereo
Audio System
For LX and EX models
Your Honda’s audio system
provides clear reception on both
AM and FM bands, while the
preset buttons allow you to easily
select your favorite stations.
The cassette system features
Dolby B* noise reduction,
automatic sensing of chromium-
dioxide (CrO
2) tape, and
autoreverse for continuous play.
* Dolby noise reduction manufactured under
license from Dolby Laboratories Licensing
Corporation. “
DOLBY” and the symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
Operating the Radio
The ignition switch must be in
ACCESSORY or ON. Turn the
system on by pressing the
PWR/
VOL knob. Adjust the volume by
turning the
PWR/VOL knob.
The band and frequency that the
radio was last tuned to is
displayed. To change bands, press
the
AM or FM button. On the FM
band, ST will be displayed if the
station is broadcasting in stereo.
Stereo reproduction on
AM is not
available.
You can use any of three methods
to find radio stations on the
selected band:
TUNE, SEEK, or
the
Preset buttons.
TUNE – Use the TUNE bar to tune
the radio to a desired frequency.
Press the right side (
) to tune to
a higher frequency, or the left side (
) to tune to a lower frequency.
The frequency numbers will start
to change rapidly. Release the bar
when the display reaches the
desired frequency. To change the
frequency in small increments,
press and release the
TUNE bar
quickly.
SEEK – The SEEK function
searches the band for a station
with a strong signal. To activate it,
press and release the
SEEK/SCAN
button. The system scans upward
from the current frequency. It
stops when it finds a station with
a strong signal.
Preset – You can store the
frequencies of your favorite radio
stations in the six preset buttons.
Each button will store one
frequency on the
AM band, and
two on the
FM band (FM1 and
FM2).
Audio System

ON/OFF/VOL KNOBSEEK/SCAN BUTTON TUNE BAR
PRESET BUTTONS
DISPLAY
AM/FM1/FM2 BUTTON
126Comfort and Convenience Features
To store a frequency:
1. Select the desired band:
AM,
FM1, or FM2.
2. Use the
TUNE or SEEK
function to find a desired
station.
3. Pick the preset button you want for that station. Press the
button and hold it until you
hear a beep.
4. Repeat steps 1 to 3 to store a total of six stations on
AM and
twelve on
FM.
Once a station’ s frequency is
stored, simply press and release
the proper preset button to tune to
it. The number of the preset
button you have selected is shown
in the display. The preset frequencies will be lost
if your vehicle’
s battery goes dead
or is disconnected.SCAN – The SCAN function
samples all the stations with
strong signals on the selected
band. To activate it, press the
SEEK/SCAN button until you hear
a beep, then release it. The system
will scan up the band for a station with a strong signal. When it finds
one, it will stop and play that
station for approximately five
seconds. If you do nothing, the
system will then scan for the next
strong station and play that for
five seconds. When it plays a
station that you want to continue
listening to, press the
SEEK/SCAN button again.

128Comfort and Convenience Features
Operating the Cassette Player
The ignition switch must be in
ACCESSORY or ON. Make sure
the tape opening on the cassette is
facing to the right, then insert the
cassette most of the way into the
slot. The system will pull it in the
rest of the way, and begin to play.
The tape direction indicator will
light to show you which side of
the cassette is playing. The

indicates the side you inserted
facing upward is now playing. If
you want to play the other side,
press the

 (preset 2) button.
If the cassette was recorded using
Dolby noise reduction, turn it on
by pressing the
(preset 5)
button. You will see
in the
display.
You can switch between the
cassette and the radio by pressing the
FM/AM and TAPE buttons.
When you press the
FM/AM
button with a cassette playing, the
radio begins to play and the
cassette stops but does not eject.
To begin playing the cassette at
the same point, press the
TAPE
button.
When the system reaches the end
of the tape, it will automatically
reverse direction and play the
other side. If you want to remove
the cassette from the drive, press
the
EJECT button.
When you turn off the ignition
switch, the system stops the tape
but does not eject the cassette. It
will begin to play when you turn
the ignition switch back on. To
eject the tape, even with the
ignition switch off, press the
EJECT button. Tape Search Functions
With a cassette playing, you can
use the
FF, REW, or APS function
to find a desired program.
FF/REW – Fast Forward and
Rewind move the tape rapidly.
Press and release the
button
(preset 1) to rewind, or the
button (preset 3) to fast forward.
You will see
REW or FF in the
display. Press the

 button to
return to
PLAY mode. If the
system reaches the end of the tape
while in fast forward or rewind, it
automatically stops that function,
reverses direction, and begins to
play.

TAPE BUTTON
CASSETTE SLOT
EJECT BUTTONTAPE DIRECTION BUTTON
FAST FORWARD
BUTTON
AUTOMATIC PROGRAM
SEARCH BUTTON AUTOMATIC PROGRAM
SEARCH BUTTON
REWIND BUTTON
DOLBY BUTTON
129Comfort and Convenience Features
APS – The Automatic Program
Search function allows you to find
the beginning of a song or
passage. Use the
(preset 4) or
(preset 6) buttons to activate
APS.
For example, the first song on the
cassette is playing, and you wish
to listen to the third song. Press
twice; you will see FF and 2
displayed. The system will fast
forward the tape to the beginning
of the third song, then return to
PLAY mode.
To return to the beginning of the
current song or passage, press
once. To return to the beginning
of the previous song, press
twice. If the system reaches the end of
the tape before finding the
selected song or passage, it
reverses direction and returns to
PLAY mode.To cancel
APS, press the

button.
The
APS function uses silent
periods on the tape to find the end
of a song or passage. This feature
may not work to your satisfaction

132 Comfort and Convenience Features
slot. The drive will pull it in the
rest of the way, and begin playing
the first track. The light next to
the button will stay on as a
reminder that a
CD
is loaded in
that position.
Repeat this procedure to load
CDs
in the remaining positions in the
changer. The positions that
contain
CDs will display a green
light next to their buttons. The
CD
position that is currently loaded
and ready to play will display an
orange light.
Playing CDs
Press the
CD button on the front
of the radio. The
CD that is
currently loaded will begin
playing. The disc and track
numbers will be shown in the
radio display. When the system
reaches the end of that
CD, it will
load and play the next
CD. To select a different disc, push the
appropriate button (1
–6) on the
front of the
CD changer. The light
next to the button will flash as the
current
CD is stored and the new
CD is loaded. The light will then
turn orange, and the
CD will
begin playing from the first track.
You can also press the
TUNE/DISC button on the front of
the radio:
to select the
previous disc, or
to select the
next disc.
To change tracks, press and
release either the
button
(preset 4), or the
button
(preset 6). Each time you press
, the system will advance one
track. Pressing
once will
return the system to the beginning
of the current track. Press it again
to select the previous track. To move rapidly within a track,
press and hold the
button
(preset 3) to move forward, or the
button (preset 1) to move
backward. Release the button
when the system reaches the point
you want.
You can switch to the radio or
cassette player by pressing the
FM/AM or TAPE buttons on the
front of the radio. To switch back
to the
CD changer, press the CD
button. The CD will begin playing
where it left off.
To eject a
CD, select it with the
button on the front of the
CD
changer (the light turns to
orange), then press the
EJECT
button.
Protecting Compact Discs
For information on how to handle
and protect compact discs, see
page 146.

133Comfort and Convenience Features
AM/FM/Cassette/CD
Changer Stereo
Audio System
For EX-L model
Your Honda’s audio system
provides clear reception on both
AM and FM bands, while the
preset buttons allow you to easily
select your favorite stations.
The CD changer holds up to six
discs, providing several hours of
continuous entertainment.
The cassette system features
Dolby B* noise reduction,
automatic sensing of chromium-
dioxide (CrO
2) tape, and
autoreverse for continuous play.
* Dolby noise reduction manufactured under
license from Dolby Laboratories Licensing
Corporation. “
DOLBY” and the symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
Operating the Radio
The ignition switch must be in
ACCESSORY or ON. Turn the
system on by pressing the
PWR/VOL knob. Adjust the
volume by turning the PWR/VOL
knob.
The band and frequency that the
radio was last tuned to is
displayed. To change bands, press
the AM or FM button. Press the
FM button again to switch
between FM1 and FM2. On the
FM band, ST will be displayed if
the station is broadcasting in
stereo. Stereo reproduction on
AM is not available.
You can use any of four methods
to find radio stations on the
selected band: TUNE, SEEK,
SCAN , or the Preset buttons.
TUNE – Use the TUNE bar to
tune the radio to a desired frequency. Press the right side
(
) to tune to a higher frequency,
or the left side (
) to tune to a
lower frequency. The frequency
numbers will start to change
rapidly. Release the bar when the
display reaches the desired
frequency. To change the
frequency in small increments,
press and release the TUNE bar
quickly.
SEEK – The SEEK function
searches the band for a station
with a strong signal. To activate it,
press and release the
SEEK/SCAN button. The system
scans up the band from the current
frequency. It stops when it finds a
station with a strong signal.
SCAN – The SCAN function
samples all the stations with
strong signals on the selected
band. To activate it, press and
hold the SEEK/SCAN button until

PWR/VOL
KNOB
AUDIO
CONTROL
KNOB
FM
BUTTON
AM
BUTTON
TUNE BAR SCAN/SEEK BUTTON
PRESET BUTTONS
134Comfort and Convenience Features
you hear a beep, then release it.
SCAN shows in the display. The
system scans up the band for a
station with a strong signal. When
it finds one, it stops and plays that
station for approximately five
seconds. If you do nothing, the
system scans for the next strong
station and plays that for five
seconds. When it finds a station
that you want to continue
listening to, press the
SEEK/SCAN button again.
Preset
– You can store the
frequencies of your favorite radio
stations in the six preset buttons.
Each button will store one
frequency on the AM band, and
two on the FM band (FM1 and
FM2).
To store a frequency:
1. Select the desired band; AM, FM1, or FM2.