2002 HONDA CIVIC Gasket

Engine Assembly
18.
Engine Installation {cont'dl
10 x 1.25 mm33 N.m {3.i1kgf.m,25 tbt.ftl
19.
20.
Connect the suspension lower arm ball joints (see
step 6 on page 18-19).
Connect the stabilizer links (see page 18-18).
Install the three way catalytic converter (TWC)
assembly (A); use new gaskets (B) and new self-
locking nuts {C).
\D
21.
-d
,ry6\
8 x 1.25 mm22N.m |.2.2kgl m,16 tbt.ft)
Connect the air fuel ratio (4,/F) sensor connector (D)
and secondary heated oxygen sensor (secondary
HO2S) connector (E).
Install the lower radiator hose.
5-12
va
23. Installthe splash shield.
24.
25.
26.
Lower the hoist.
Installthe drive belt.
Installthe A,/C line mounting bolt.
6 x '!.0 mm9.8 N.m (1.0 kgf.m,7.2 tbt.ftl
. -t- --- ----r

SPRINGRETAINER
EXHAUST VALVESEAL
vALvE / .""or", uo.u,.
ll"
l* I / uo.ur.r","o
--€.i
d:l.\aFl
T1ll
ll
H
,p
2bw
9) \*""'RArNERcovER

wcsrRArNER
CYLINDER HEADRemoval, page 6'23Inspection, page 6-25Installation, page 6-39
EXHAUST VALVERemoval, page 6-31Installation, page 6-37
INTAKE VALVERemoval, page 6 31Installation, page 6 37
CYLINDER HEADGASKET
,H v .-- spntruc>il( G\-r_
\lg
| | g -/ TNTAKE vALVE
II ^-'-- 9E4LI I U- Replacement, Page 6-31
He,tl E- _-/ |NTAKE VALVEY I 1.- GUIDE
U Replacement, page 6-33
i
HEAT SHIELD
6-5

Cylinder Head
Engine Compression Inspection
1. Warm up the engine to normal operating
temperature (cooling fan comes on).
2. Turn the ignition switch OFF.
3. Remove the intake manifold cover (see step 1 onpage 6-22).
4, Disconnect all four injector connectors.
5. Start the engine, and let it run until it stalls.
6. Remove the iour ignition coils (see page 4-18).
7. Remove the four spark plugs.
8. Attach the compression gauge to the spark plug
note.
6-6
V,
\
9.
10.
Open the throttle fully, then crank the engine with
the starter motor and measure the compression.
Compression Pressure
Above 930 kpa (9.5 kgf/cm', 135 psi)
Measure the compression on the remaining
cylinders,
Maximum vadation
Within 200 kPa (2.0 kgf/cm', 28 psi)
lf the compression is not within specifications,
check these items, then remeasure the
compressron.
. Damaged orworn valves and seats. Damaged cylinder head gasket. Damaged or worn piston rings. Damaged orworn piston and cylinder bore
11.
\-

7, Install the cam chainguide B.
H4
\ilt
Hgq
8 x 1.25 mm22 N.m(2.2 kgf.m, 16lbt.ft)
8. Remove the Din from the auto-tensioner,
Check the chain case oil seal for damage. lf the oil
seal is damaged, replace the chain case oil seal
(see page 6-21).
9.
10.
11.
Remove old liquid gasket from the chain case
mating surfaces, bolts, and bolt holes.
Clean and dry the chain case mating surfaces.
Apply liquid gasket. P/N 08718-0009, evenly to the
cylinder block mating surface ofthe chain case and
to the inner threads of the holes.
Apply liquid gasket to the cylinder block upper
surface contact areas (A) on the chain case.
Apply liquid gasket, PiN 08718-0009, evenly to the
oil pan mating surface of the chain case and to the
inner threads of the holes.
NOTE: Do not installthe parts it 5 minutes or more
have elapsed since applying liquid gasket. lnstead,
reapply liquid gasket after removing old residue.
(cont'd)
14.
Apply liquid gasketalong the broken line.
Apply liquid gasketalong the broken line.
6-17

Remove old liquid gasket from the chain case cover
mating surfaces, bolts, and bolt holes.
Clean and dry the chain case cover mating surfaces.
Apply liquid gasket, P/N 08718-0009, evenly to the
chain case mating surface of the chain case cover
and to the inner threads of the holes.
NOTE: Do not installthe parts if 5 minutes or more
have elapsed since applying liquid gasket. Instead,
reapply liquid gasket after removing old residue.
6. Installthe chain case cover.
4.
6x1.0mm12 N.m{1.2 kgt.m,8.7 tbf.ft)
Apply liquid gasketalong the broken line.
Chain Case Oil Seal Installation
SpecialTools Required. Driver 07749-0010000. Attachment, 52 x 55 mm 07746-0010400
1. Use the special tools to drive a new ollseal
squarely into the chain case to the specified
installed height.
07749-0010000
2. Measure the distance between the chain case
surface (A) and oilseal 1B).
Oil Seal Installed Height:
33.0-33.7 mm (1.30- 1.33 in.)
33.0 33.7 mm{1.30 1.33 in.l
6-21

Cylinder Head
Rocker Arm Assembly Installation
:,ean and dry the No. 5 rocker shaft holder mating
surfaces.
eeassemble the rocker arm assembly (see page 6-
21 t.
Apply liquid gasket, P/N 08718-0009, evenly to the
:ylinder head mating surface ofthe No. 5 rocker
shaft holder.
\OTE: Do not lnstall the parts if 5 minutes or more
rave elapsed since applying liquid gasket. Instead,'eapply liquid gasket after removing old residue.
Insert the bolts (A) into the rocker shaft holder, then
install the rocker arm assembly (B) on the cylinder
head.
Apply liquid gasketalong the broken line.
6-38
l-
\
5.
6.
Remove the bolts from the rocker shaft holder.
Make sure the DUnch marks on the variable valve
timing control (VTC) actuator and exhaust camshaft
sprocket are facing up. then set the camshafts (A) in
the holder.
Set the camshaft holders (B) and cam chain guide B
(C) in place.
Tighten the bolts to the specified torque.
Specified torque:
8 mm bolts: 22 N.m (2.2 kgf.m, 16 lbl.ft)
6 mm bolts: 12 N.m {1.2 kgf.m,8.7 lbf.fil
6 mm bolts: @),@.@
lnstall the cam chain (see page 6-15). and adjust the
valve clearance (see page 6-9).
I
flc
a\-
7.
{

Cylinder Head Installation
Install the cylinder head in the reverse order of
removat:
1. Clean the cylinder head and block surface.
2. Install the new cylinder head gasket (A) anddowel
pins (B) on the cylinder block. Always use a new
cylinder head gasket.
Set the crankshaft to top dead center {TDC). Align
the TDC mark (A) on the crankshaft sprocket with
the pointer (B) on the cylinder block.
4. Install the cylinder head on the block.
5. Measure the diameter of each cylinder head bolt at
ooint A and Doint B.
a 50 mm (2.0 in.l
f.f )>-
A '15 mm {'1.8 in.)"<>.
lf either diameter is less than 10.6 mm {0.42 in.),
replace the cvlinder head bolt.
(cont d)
6-39

14. Installthe water bvpass hose.
15. Installthe air cleaner housing (see step 37 on page
5-15).
16. Installthe intake manifold (see page 9-5).
17. Installthe exhaust manifold (see page 9-7).
'18. Installthe cam chain (see page 6-15).
19. Adjust the valve clearance (seepage6-9).
20. Installthe drive belt (see page 4-26).
21. Clean the battery posts and cable terminals with
sandpaper, then assemble them and apply grease
to prevent corrosion.
22. After installation, checkthatall tubes, hosesand
connectors are installed correctly.
23. Inspectforfuel leaks. Turn the ignition switch ON
{ll) {do not operate the starter) so that the fuel pump
runs for about 2 seconds and pressurizes the fuel
line. Repeat thls operation two or three times, then
check for fuel leakage at any point in the fuel line.
24. Refillthe radiator with engine coolant, and bleed
air from the cooling system with the heater valve
open (see page 10-6).
25. Inspect the idle speed (see page 11-'138).
26. Inspect the ignition timing (see page 4-17).
Gylinder Head Cover lnstallation
1. Thoroughly clean the head cover gasket and the
groove.
2. Installthe head cover gasket (A) in the groove of
the cylinder head cover (B).
Check that the mating surfaces are clean and dry.
Apply liquid gasket. P/N 08718-0009, on the chain
case and the No.5 rocker shaft holder mating areas.
NOTE: Do not install the parts if 5 minutes or more
have elapsed since applying liquid gasket. Instead,
reapply liquid gasket after removing old residue.
(cont'd)
6-41