2002 GMC ENVOY Owner's Manual

3-42
RPT: With repeat, you can repeat one track or an entire
disc. To use repeat, do the following:

To repeat the track you are listening to, press and
release the RPT button. RPT will appear on the
display. Press RPT again to turn it off.

To repeat the disc you are listening to, press and hold
the RPT button for two seconds. RPT will appear on
the display. Press RPT again to turn it off.
RDM: With random, you can listen to the tracks in
random, rather than sequential order, on all of the discs
or on one disc. To use random, do the following:

Press and release the RDM button to play the tracks
on all of the discs that are loaded, in random order.
RDM will appear on the display. Press RDM to turn
it off.

To play the tracks on the disc you are listening to in
random order, press and hold RDM for more than
two seconds. You will hear a beep and RDM will
appear on the display. Press RDM again to turn it off.
AUTO EQ: Press AUTO EQ to select the desired
preset equalization setting while playing a compact disc.
The equalization will be automatically set whenever you
play a compact disc. For more information on AUTO
EQ, see ªAUTO EQº listed previously in this section.
SEEK SCAN: To seek, press the left arrow while
playing a CD to go to the start of the current track,
if more than ten seconds have passed. Press the right
arrow to go to the next track. If you press the button
more than once, the player will continue moving
backward or forward through the disc.
To scan one disc, press and hold either SEEK SCAN
arrow for more than two seconds until SCAN appears
on the display and you hear a beep. Use SEEK SCAN
to listen to each track of the currently selected disc
for ten seconds. The sound will mute while scanning.
SCAN will appear on the display. Press either SEEK
SCAN arrow again, to stop scanning.
To scan all loaded discs, press and hold either SEEK
SCAN arrow for more than four seconds until DISC
SCAN appears on the display and you hear a beep.
Use DISC SCAN to listen to the first track, for ten
seconds for each disc loaded. The sound will mute while
scanning to the next track. DISC SCAN will appear
on the display. Press either SEEK SCAN arrow again,
to stop scanning.

3-43
TUNE RCL P-TYPE: Press this control to see how
long the current track has been playing. To change what
is normally shown on the display (track or elapsed
time), press the control until you see the display you
want, then hold the control until the display flashes.
AM FM: Press this button to play the radio when a disc
is in the player.
Using Song List Mode
The integrated 6
-disc CD changer has a feature
called song list. This feature is capable of
saving 20 track selections.
To save tracks into SONG LIST perform the
following steps:
1. Turn the disc player on and load it with at least one
disc. See ªLOAD CDº mentioned previously for
more information.
2. Check to see that the disc changer is not in song list
mode. S
-LIST should not appear in the display.
If S
-LIST is present, press SONG LIST to turn it off.3. Select the desired disc by pressing the numbered
pushbutton and then use the SEEK SCAN right
arrow button to locate the track that you want to
save. The track will begin to play.
4. Press and hold the SONG LIST button for two
or more seconds to save the track into memory.
When SONG LIST is pressed a beep will be heard
immediately. After two seconds of pressing SONG
LIST continuously, two beeps will sound to confirm
that the track has been saved.
5. Repeat Steps 3 and 4 for saving other selections.
If you attempt to save more than 20 selections, S
-LIST
FULL will appear on the display.
To play the song list, press SONG LIST. One beep will
be heard and S
-LIST will appear on the display.
The recorded tracks will begin to play in the order that
they were saved.
You may seek through the song list by using the SEEK
SCAN arrows. Seeking past the last saved track will
return you to the first saved track.

3-44
To delete tracks from SONG LIST perform the
following steps:
1. Turn the disc player on.
2. Press SONG LIST to turn song list on. S
-LIST will
appear on the display.
3. Press the SEEK SCAN arrows to select the desired
track to be deleted.
4. Press and hold the SONG LIST button for two
seconds. When pressing SONG LIST one beep will
be heard immediately. After two seconds of pressing
the SONG LIST button continuously, two beeps will
be heard to confirm that the track has been deleted.
After a track has been deleted, the remaining tracks are
moved up the list. When another track is added to the
song list, the tracks will be added to the end of the list.To delete the entire SONG LIST perform the
following steps:
1. Turn the disc player on.
2. Press SONG LIST to turn song list on. S-LIST will
appear on the display.
3. Press and hold SONG LIST for more than four
seconds. A beep will be heard, followed by two
beeps after two seconds and a final beep will be
heard after four seconds. S
-LIST EMPTY will
appear on the display indicating that the song list
has been deleted.
If a disc is ejected, and the song list contains saved
tracks from that disc, those tracks are automatically
deleted from the song list.
To end SONG LIST mode, press the SONG LIST
button. One beep will be heard and S
-LIST will be
removed from the display.

3-45
Compact Disc Messages
(Check CD): If this message appears on the
radio display, it could be due to one of the
following conditions:

The road is too rough. The disc should play when
the road is smoother.

The disc is dirty, scratched, wet or upside down.

The air is very humid. If so, wait about an hour
and try again.
If any error occurs repeatedly or if an error can't be
corrected, please contact your dealer. If your radio
displays an error message, write it down and provide it
to your dealer when reporting the problem.Rear Seat Entertainment System
(RSE) (If Equipped)
Your vehicle may have the optional Digital Versatile
Disc (DVD) entertainment system. The entertainment
system includes a DVD player, a video display screen,
two sets of IR wireless headphones, a remote control
and an instructional video disc.
Before You Drive
The video entertainment system is for passengers in
the second and third row seats only. The driver cannot
safely view the video screen while driving and should
not try to do so.
In severe or extreme temperature conditions your
entertainment system should not be operated until the
temperature is within the operating range. This will keep
your video components from being damaged when the
temperature is below
-4F (-20C) or above 140F (60C).
To resume operation, shut off the entertainment system,
pull down the video screen and then heat or cool the vehicle
until the temperature is within the operating range.

3-46 Headphones
The entertainment system includes two
IR wireless headphones.
Mini
-headphone jacks are also provided for use
with customer provided headphones.
The wireless headphones have an ON/OFF switch
and a volume control. To use the headphones turn the
switch to ON. An indicator light will illuminate. If the
light does not illuminate, the batteries may need to be
replaced. See ªBattery Replacementº later in this
section for more information. Switch the headphones
to OFF when not in use.
If the system is shut off, or if the headphones are out
of range of the IR transmitters below the overhead
RSE control panel for more than three minutes,
the headphones will shut off automatically to save the
battery. If you move too far forward or step out of the
vehicle, the headphones will lose the audio signal.
To adjust the volume on both pairs of wired headphones,
use the volume control.
NOTICE:
Do not store the headphones in heat or direct
sunlight. This could damage the headphones
and would not be covered by your warranty.
Keep the headphones stored in a cool, dry place.
Battery Replacement
To change the batteries, do the following:
1. Loosen the screw on the battery compartment
door located on the left side of the headphones.
2. Remove the batteries from the compartment.
3. Replace the two AAA batteries. Make sure that
they are installed correctly.
If the headphones are to be stored for a long period
of time, remove the batteries and keep them in a cool,
dry place.

3-47 Stereo RCA Jacks
The RCA jacks and the mini-headphone jacks are
located behind the video screen on the overhead console.
The RCA jacks allow you to hook up an auxiliary device
such as a camcorder or a video game unit. The yellow
RCA jack is used for video and the red and white RCA
jacks are used for audio. You may require adapter
connectors or cables to connect your auxiliary device to
the RCA jacks. Refer to the manufacturer's instructions
for proper usage. The mini
-headphone jacks allow you
to hook up customer provided wired headphones.
To use the auxiliary audio and video inputs on the RSE,
connect an external auxiliary device such as a camcorder
to the RCA jacks and turn on both the auxiliary device
power and the power on the front of the RSE player.
If a disc is not present in the player, the auxiliary signal
will immediately be displayed on the RSE. If a disc is
present when the RSE power is turned on, the player will
automatically begin playing the disc and the user will need
to press the AUX button on the remote control to display
and/or hear the auxiliary input signals. Each successive
press of the AUX button on the remote control will switch
the system between disc and auxiliary input. The wired
headphone volume control will only operate when the
DVD player power is turned on and it controls both wired
headphone jacks at the same time. See ªRemote Controlº
later in this section for more information.
Audio Speakers
Audio from the DVD player can only be heard either
through the IR headphones or wired headphones
(not included). The sound will not come through the
vehicle's speakers.
Video Screen
The video screen is located in the overhead console.

3-48
To use the video screen, do the following:
1. Push forward on the release button and the screen
will fold down.
2. Push the screen away from you and adjust its
position as desired.
When the video screen is not in use, push it up into
its locked position.
The DVD player and display will continue to operate
when the display is in either the up or down position.
NOTICE:
Avoid directly touching the video screen,
as damage may occur. See ªCleaning the Video
Screenº in the Index for more information.
DVD Player
The DVD player is located in the overhead console.
The DVD player can be controlled by the buttons
on the DVD player and by the buttons on the remote
control. See ªRemote Controlº later in this section
for more information.
The DVD player works while the ignition is in
RUN or ACCESSORY and while RAP is active.
See ªRetained Accessory Power (RAP)º in the Index
for more information.

3-49
The entertainment system is only compatible with
Region 1 DVDs authorized for use in the United States,
Canada, Puerto Rico, Bermuda, the Virgin Islands
and some islands in the Pacific. On some DVD jackets,
you will see the region displayed. Regular audio CDs
can also be played by the DVD player. The video
screen will default to off when an audio CD is played.
Home recorded CDs (CDRs) will not play in this
DVD player. Try the audio system's CD player instead.
If an error message appears on the front instrument
panel display, see ªDVD Messagesº later in this section.
DVD Player Buttons
(Power): Press this button to turn the DVD
player on.
(Headphone Volume): Press the minus (±)
symbol to decrease headphone volume. Press the
plus (+) symbol to increase headphone volume.
(Play/Pause): Press this button to start play.
Press this button while a DVD is playing to pause it.
Press it again to continue playing the DVD.
(Stop/Eject): Press this button to stop playing,
rewinding or fast forwarding. Press the button a second
time to eject the disc.Playing a Disc
To play a disc, gently insert the disc (with the label
side up) into the loading slot. The DVD player
will continue loading the disc and the player will
automatically start.
If a disc is already in the player, press the play/pause
button on the face of the player or on the remote control.
Some DVDs will not allow you to fast forward or
skip the copyright or previews. Some DVDs will begin
playing after the previews have finished. If the DVD does
not begin playing, refer to the on
-screen instructions.
Stopping and Resuming Playback
To stop a disc, press and release the stop/eject button
on the DVD player or the stop button on the remote.
To resume playback, press the play/pause button on the
DVD player or the remote. As long as the disc has not
been ejected and the stop button has not been pressed
twice on the remote control, the movie should resume
play from where it was last stopped. If the disc has been
ejected, or if the stop button on the remote has been
pressed twice, the disc will resume play at the beginning.