2002 CHEVROLET TRAIL BLAZER CD player

3-40
2 NEXT: Press this button to go to the next selection
on the tape. If you press the button more than once, the
player will continue moving forward through the tape.
SEEK and a positive number will appear on the display.
Your tape must have at least three seconds of silence
between each selection for next to work. To forward
through each selection press the right SEEK PSCAN
arrow. The sound will mute while seeking.
3 REV: Press this button to reverse the tape rapidly.
Press it again to return to playing speed. The radio will
play the last selected station while the tape reverses. The
station frequency and REV will appear on the display.
You may select stations during reverse operation by
using TUNE DISP and the SEEK PSCAN arrows.
4 FWD: Press this button to advance quickly to another
part of the tape. Press the button again to return to
playing speed. The radio will play the last selected
station while the tape advances. The station frequency
and FWD will appear on the display. You may select
stations during forward operation by using TUNE DISP
and the SEEK PSCAN arrows.
5 SIDE: Press this button to play the other side of
the tape.
6
RDM: Press this button to reduce background
noise. NR ON will appear on the display. Press it again
to turn Dolby off. NR OFF will appear on the display.Dolby Noise Reduction is manufactured under a license
from Dolby Laboratories Licensing Corporation. Dolby
and the double
-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
 SEEK PSCAN
: SEEK PSCAN (right arrow) is
the same as 2 NEXT, and SEEK PSCAN (left arrow) is
the same as 1 PREV. If the button is held or pressed
more than once, the player will continue moving
forward or backward through the tape. SEEK and a
positive or negative number will appear on the display.
AM FM: Press this button to play the radio when
a tape is in the player. The tape will stop but remain in
the player.
TAPE CD: With a tape in the player and the radio
playing, press this button to play a tape. Press AM FM
to return to the radio when a tape is playing. Press TAPE
CD to switch between the tape and compact disc if both
are loaded. The inactive tape or CD will remain safely
inside the radio for future listening.
EJT: Press this button to remove a tape. The radio
will play. Eject may be activated with the radio off.
Cassette tapes may be loaded with the radio off if this
button is pressed first.

3-41
Cassette Tape Messages
(CHK TAPE): If CHK TAPE appears on the radio
display, the tape won't play because of one of the
following errors.

The tape is tight and the player can't turn the tape
hubs. Remove the tape. Hold the tape with the
open end down and try to turn the right hub
counterclockwise with a pencil. Turn the tape over
and repeat. If the hubs do not turn easily, your tape
may be damaged and should not be used in the
player. Try a new tape to make sure your player is
working properly.

The tape is broken. Try a new tape.

The tape is wrapped around the tape head. Attempt
to get the cassette out. Try a new tape.(CLEAN): If this message appears on the display, the
cassette tape player needs to be cleaned. It will still play
tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See ªCare of
Your Cassette Tape Playerº in the Index. After you clean
the player, press and hold the cassette eject button for
five seconds to reset the CLEAN indicator. The radio
display will display CLEANED to show the indicator
was reset.
If any error occurs repeatedly or if an error can't be
corrected, please contact your dealer.
Tight/Loose Tape Sensor Defeat
With the radio off and the ignition on, press and hold the
TAPE CD button to disable the tight/loose tape sensing
feature to enable play of some tape head cleaners and
portable CD adapters. The radio will display READY
and flash the cassette icon. The tight/loose tape sensing
feature will then be disabled until the next time a
cassette is ejected.

3-42
Playing a Compact Disc
Insert a disc partway into the slot, label side up. The
player will pull it in and the disc should begin playing.
The display will show the CD symbol. If you want to
insert a compact disc with the ignition off, first press
TUNE DISP or EJT.
If an error appears on the display, see ªRadio/Compact
Disc Messagesº later in this section.
1 PREV: Press this button or the left SEEK PSCAN
arrow to go to the previous track if the current selection
has been playing for less than eight seconds. If the
1 PREV button or the left SEEK PSCAN arrow is
pressed and the current selection has been playing for
more than eight seconds, it will go to the beginning of
the current selection. TRACK and the track number will
appear on the display. If you hold the 1 PREV button
or left SEEK PSCAN arrow or press it more than once,
the player will continue moving back through the disc.
The sound will mute while seeking.
2 NEXT: Press this button or the right SEEK PSCAN
arrow to go to the next track. TRACK and the track
number will appear on the display. If you hold the
2 NEXT button or the right SEEK PSCAN arrow or
press it more than once, the player will continue
moving forward through the disc. The sound will mute
while seeking.3 REV: Press and hold this button to reverse quickly
within a track. Press and hold this button for less than
two seconds to reverse at six times the normal playing
speed. Press and hold it for more than two seconds to
reverse at 17 times the normal playing speed. Release it
to play the passage. The display will show ET and the
elapsed time.
4 FWD: Press and hold this button to advance quickly
within a track. Press and hold this button for less than
two seconds to advance at six times the normal playing
speed. Press and hold it for more than two seconds to
advance at 17 times the normal playing speed. Release it
to play the passage. The display will show ET and the
elapsed time.
6
RDM: Press this button to hear the tracks in
random, rather than sequential, order. RDM ON will
appear on the display. RDM T and the track number will
appear on the display when each track starts to play.
Press 6 RDM again to turn off random play. RDM OFF
will appear on the display.
 SEEK PSCAN
: Press the left SEEK PSCAN
arrow to go to the start of the current or previous track.
Press the right SEEK PSCAN button to go to the start of
the next track. If either of the SEEK PSCAN arrows is
held or pressed more then once, the player will continue
moving backward or forward through the CD.

3-43
TUNE DISP: Press this control to see how long the
current track has been playing. ET and the elapsed time
will appear on the display. To change what is normally
shown on the display (track or elapsed time), press the
control until you see the display you want, then hold
the control for two seconds. The radio will produce
one beep.
AM FM: Press this button to play the radio when
a disc is in the player. The disc will stop but remain in
the player.
CD AUX: With a CD in the player and the radio
playing, press this button to play a CD. Press AM FM
to return to the radio when a CD is playing. The inactive
CD will remain safely inside the radio for
future listening.
EJT: Press this button to remove the disc. The
radio will play. Eject may be activated with either the
ignition or radio off. CDs may be loaded with the radio
and ignition off if this button is pressed first.Compact Disc Messages
(Err): If you're driving on a very rough road or if it's
very hot, the disc may not play and Err (error) may
appear on the display. When the road becomes smooth
or the temperature returns to normal, the disc should
play. If the disc comes out, it could be one of
the following:

The disc is upside down.

It is dirty, scratched or wet.

It is very humid. (If so, wait about an hour
and try again.)
If any error occurs repeatedly or if an error can't be
corrected, please contact your dealer.
(CAL ERR): This message is displayed when the radio
has not been calibrated properly for the vehicle. You
must return to the dealership for service.
(LOCKED): This message is displayed when the
THEFTLOCK
 system has locked up. You must return
to the dealership for service.

3-44 AM-FM Stereo with 6-Disc Compact
Disc Player with Programmable
Equalization and Radio Data
System (RDS) (If Equipped)
Standard radio--Bose
not shownPlaying the Radio
VOLUME PWR: Press this control to turn the system
on and off. To increase volume, turn the control
clockwise. Turn it counterclockwise to decrease volume.
AUTO VOL: Your system has a feature called
automatic volume. With this feature, your audio system
adjusts automatically to make up for road and wind
noise as you drive. Set the volume at the desired level.
Press this button to select MIN, MED, MAX or OFF.
Each choice allows for more volume compensation at
faster vehicle speeds. Then, as you drive, automatic
volume automatically increases the volume, as
necessary, to overcome noise at any particular speed.
The volume level should always sound the same to you
as you drive. If you don't want to use automatic volume,
select OFF.
If your vehicle has the Bose radio, your audio system
monitors the noise inside your vehicle. Then,
automatically adjusts the volume so that it always
sounds the same to you. To use automatic volume, press
the AUTO VOL button until AVOL ON appears on the
display. To turn automatic volume off, press the AUTO
VOL button until AVOL OFF appears on the display.

3-47
If your vehicle has the Bose radio, your audio system
allows you to choose from four different equalization
settings: talk, driver, normal and spatial. These settings
can be used while listening to the radio or the CD player.
Press the AUTO EQ button to scroll through your
choices. Select TALK when listening to non
-musical
material such as news, talk shows, sports broadcasts and
books on tape. This settings makes spoken words sound
very clear. Select DRIVER to give the driver the best
possible sound qualities. Select NORMAL to enhance
the stereo effect. Select SPATIAL to make the listening
space seem larger. When AUTO EQ NORMAL is
displayed, the system will provide the best overall Bose
performance. The radio saves separate AUTO EQ
settings for each preset and source.Adjusting the Speakers
AUDIO (Balance/Fade): The AUDIO control
adjusts balance and fade. To adjust balance, press the
AUDIO control until BAL appears on the display.
Turn the control to adjust the sound to the left or right
speakers. The middle position balances the sound
between the speakers.
To adjust fade, press and hold the AUDIO control until
FAD appears on the display. Turn the control to adjust
the sound to the front or rear speakers. The middle
position balances the sound between the speakers.
To set the balance and fade to the middle position, select
balance or fade and press and hold the AUDIO control.
The radio will beep once and will set the display level to
the middle position.
To set all tone and speaker controls to the middle
position, press and hold the AUDIO control when
tone or speaker controls are not active. The radio
will produce one beep and CENTERED will appear
on the display.

3-49
Setting PTY Preset Stations
The six numbered pushbuttons let you return to your
favorite Program Types (PTYs). These buttons have
factory PTY presets. You can set up to 12 PTYs
(six FM1 and six FM2) by performing the
following steps:
1. Press AM FM to select FM1 or FM2.
2. Press P
-TYPE, if it is not already on.
3. Turn the TUNE RCL P
-TYPE control to
select a PTY.
4. Press and hold one of the six numbered pushbuttons
until you hear a beep. Whenever you press that
numbered pushbutton, the PTY you set will return.
5. Repeat the steps for each pushbutton.
Radio Announcements
(Alert): Warns of national or local emergencies. You will
not be able to turn off alert announcements. ALERT!
appears on the display when an alert announcement plays.
When an alert announcement comes on the tuned radio
station, you will hear it, even if the volume is muted or a
compact disc is playing. If the compact disc player is
playing, play will stop for the announcement and resume
when the announcement is finished.INFO: If the current station has a message, INFO will
appear on the display. Press this button to see the
message. If the whole message does not appear on the
display, parts of the message will appear every three
seconds until the message is completed. To see the parts
of the message faster than every three seconds, press this
button again. A new group of words will appear on the
display. Once the complete message has been displayed,
INFO will disappear from the display until another new
message is received.
TRAF: Press this button to receive traffic
announcements. The traffic announcement brackets will
appear on the display. TRAF will appear on the display
if the tuned station broadcasts traffic announcements.
If the current tuned station does not broadcast traffic
announcements, the radio will seek to a station that
does. When the radio finds a station that broadcasts
traffic announcements, it will stop. If no station is found,
NONE FOUND will appear on the display.
When a traffic announcement comes on the tuned radio
station or a related network station, you will hear it,
even if the volume is muted or a compact disc is
playing. If the compact disc player was being used, the
compact disc will stay in the player and resume play at
the point where it stopped.

3-50
Playing a Compact Disc
LOAD CD
: Press this button to load CDs into the
compact disc player. This compact disc player will
accommodate up to six discs.
To insert one disc do the following:
1. Turn the ignition on.
2. Press and release the LOAD CD button.
3. Wait for the light, located to the right of the slot, to
turn green.
4. Load a disc. Insert a disc partway into the slot, label
side up. The player will pull the disc in.
When the disc is inserted, the CD symbol will be
displayed. If you select an EQ setting for your disc,
it will be activated each time you play a disc.
If the radio is on or off, the disc will begin to
play automatically.
To insert multiple discs do the following:
1. Turn the ignition on.
2. Press and hold the LOAD CD button for two seconds.
You will then hear a beep and the light, located to the
right of the slot, will begin to flash.3. Once the light stops flashing and turns green, load a
disc. Insert a disc partway into the slot, label side up.
The player will pull the disc in.
Once the disc is loaded, the light will begin flashing
again. Once the light stops flashing and turns green
you can then load another disc. The disc player takes
up to six discs. Do not try to load more than six.
When a disc is inserted, the CD symbol will be
displayed. If more than one disc has been loaded, a
number for each disc will be displayed. If you select
an EQ setting for your disc, it will be activated each
time you play a disc.
If the radio is on or off, the last disc loaded will
begin to play automatically.
4. To load more than one disc but less than six,
complete Steps 1, 2 and 3. When you have finished
loading discs, with the radio on or off, press the
LOAD CD button to cancel the loading function.
The radio will begin to play the last CD loaded.
As each new track starts to play, the track number will
appear on the display.