2002 CADILLAC ESCALADE lock

4-46 Dinghy Towing (Two-Wheel Drive
Vehicles Only)
Tw o-wheel-drive vehicles, should not be towed with
all four wheels on the ground. Two
-wheel-drive
transmissions have no provisions for internal lubrication
while being towed. To properly tow these vehicles,
they should be placed on a platform trailer with all
four wheels off the ground.
In rare cases when it's unavoidable that a
two
-wheel-drive vehicle is to be towed with all four
wheels on the ground, the propeller shaft to axle yoke
orientation should be marked and the propeller shaft
removed following the applicable service manual
removal/installation procedure.
Dust or dirt can enter the back of the transmission
through the opening created by removing the propeller
shaft if proper protection is not provided. Also, check
the transmission fluid level before driving the truck.When the vehicle is properly attached to the tow vehicle
and is ready to be towed, turn the ignition to OFF.
The OFF position unlocks the steering column and will
allow the proper movement of the front wheels and tires
during towing. To prevent the battery from draining,
remove the IGN 0 fuse from the instrument panel fuse
block. See ªFusesº in the Index for more information
about removing the IGN 0 fuse.NOTICE:
Towing an all-wheel-drive vehicle with all four
wheels on the ground, or even with only two of
its wheels on the ground, will damage drivetrain
components. Don't tow an all
-wheel drive vehicle
if any of its wheels will be on the ground.

4-47 Dolly Towing (Two-Wheel Drive
Vehicles Only)
Tw o-wheel-drive vehicles, should not be towed with
the rear wheels on the ground. Two
-wheel-drive
transmissions have no provisions for internal lubrication
while being towed. To properly tow these vehicles,
they should be placed on a platform trailer with all
four wheels off the ground.
In rare cases when it's unavoidable that a
two
-wheel-drive vehicle is to be towed with the rear
wheels on the ground, the propeller shaft to axle yoke
orientation should be marked and the propeller shaft
removed following the applicable service manual
removal/installation procedure.
Dust or dirt can enter the back of the transmission
through the opening created by removing the propeller
shaft if proper protection is not provided. Also, check
the transmission fluid level before driving the truck.When the vehicle is properly attached to the dolly and
tow vehicle and is ready to be towed, turn the ignition to
LOCK. To prevent the battery from draining, remove
the IGN 0 fuse from the instrument panel fuse block.
See ªFusesº in the Index for more information about
removing the IGN 0 fuse.
NOTICE:
Towing an all-wheel-drive vehicle with all four
wheels on the ground, or even with only two of its
wheels on the ground, will damage drivetrain
components. Don't tow an all
-wheel-drive vehicle
if any of its wheels will be on the ground.

4-61
Instrument Panel Jumper Wiring Harness
This harness is included with the heavy-duty and
camper/fifth
-wheel trailer wiring packages. The harness
is for an electric trailer brake controller and includes a
trailer battery feed fuse. This harness and fuse should be
installed by your dealer or a qualified service center.Four Wire Trailer Harness Adapter
If you need to tow a
light
-duty trailer with a
standard four
-way round
pin connector, an adapter
connector is included in
your vehicles glove box.
Connect the adapter with the tab (arrow) pointing
towards to the top. The cap on the wiring harness will
lock onto the tab (arrow) and help hold the adapter
in place.

5-16
Your vehicle may be
equipped with one of
the two caps shown.
1. You can remove the coolant surge tank pressure
cap when the cooling system, including the coolant
surge tank pressure cap and upper radiator hose,
is no longer hot. Turn the pressure cap slowly
counterclockwise (left) about one full turn. If you
hear a hiss, wait for that to stop. A hiss means there
is still some pressure left.

5-20
Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving slowly to a level place. Turn on your hazard
warning flashers.
CAUTION:
Changing a tire can cause an injury. The vehicle
can slip off the jack and roll over you or other
people. You and they could be badly injured.
Find a level place to change your tire. To help
prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine.
4. Put the wheel blocks at the front and
rear of the tire farthest away from the
one being changed. That would be the
tire on the other side of the vehicle,
at the opposite end.The following steps will tell you how to use the jack and
change a tire.

5-21 Removing the Spare Tire and Tools
The equipment is located under the rear seat behind the
driver's seat and behind the left trim panel in the rear
of the vehicle.
Under Second Row Passenger's Seat on Driver's Side
A. Tool Kit with Jack
Tools and GlovesB. Bracket and
Wing Nut
There is a wing nut (B) used to retain the tool kit (A).
To remove it, turn the wing nut counterclockwise.
Rear Access Panel
A. Speaker
B. Bottle Jack
C. Wing NutD. Retaining Hook
E. Wheel Blocks
F. Cover Panel
To release the bottle jack (B) from its holder,
turn the knob on the bottle jack counterclockwise
to lower the jack head.
The wheel blocks (E) and the wheel block
retainer can be removed by turning the wing
nut (C) counterclockwise.
You'll use the jack handle extensions and the wheel
wrench to remove the underbody
-mounted spare tire.

5-22
A. Hoist Assembly
B. Wheel Wrench
C. Jack Handle
Extensions
D. Hoist Shaft
E. Valve Stem,
Pointed Up
F. Spare TireG. Tire Retainer
H. Hoist Cable
I. Hoist Lock
J. Hoist Shaft
Access Hole
K. Hoist End of
Extension Tool

5-23
Follow these instructions to lower the spare tire:
1. If the vehicle is equipped with a hoist lock (I),
open the spare tire lock cover on the bumper and
use the ignition key to remove the lock.
2. Assemble the wheel wrench (B) and the two jack
handle extensions (C) as shown. Insert the hoist end
(open end) (K) of the extension through the hole (J)
in the rear bumper. Be sure the hoist end of the
extension connects into the hoist shaft (D)
(the ribbed square end of the extension is used
to lower the spare tire (F)).
3. Turn the wheel wrench counterclockwise to lower
the spare tire to the ground. Continue to turn the
wheel wrench until the spare tire can be pulled out
from under the vehicle. The wheel wrench has a
hook that allows you to pull the hoist cable (H)
towards you, to assist in reaching the spare tire.
4. When the tire has been lowered, tilt the retainer (G)
at the end of the cable so it can be pulled up through
the wheel opening.
5. Put the spare tire near the flat tire.
The tools you'll be using include the bottle jack (A), the
wheel blocks (B), the jack handle (C), the jack handle
extensions (D), and the wheel wrench (E).
If the flat tire is on a rear tire of the vehicle, you'll need
to use both jack handle extensions.