2002 CADILLAC ESCALADE EXT clock

5-21 Removing the Spare Tire and Tools
The jack and wheel blocks are located under a cover
near the passenger side seat.
To remove the jack and wheel blocks, do the following:
Rear Seat (Passenger Side) Jack Cover
1. Remove the jack cover by turning the two wing nuts
one
-quarter turn counterclockwise and pulling the
jack cover off.
2. Remove the wheel blocks by turning the wing nut
counterclockwise.
3. Release the bottle jack from its holder by turning the
knob on the jack counterclockwise to lower the jack
head from the bracket.
The tools for changing a flat tire are located in the
passenger's side Top
-Box Storage unit.

5-23
Follow these instructions to lower the spare tire:
1. Your vehicle is equipped with a hoist lock (J).
To unlock it, open the spare tire lock cover on the
bumper and use the ignition key to remove the lock.
2. Assemble the wheel wrench (H) and the two jack
handle extensions (I) as shown.
3. Insert the hoist end
(open end) (F) of the
extension through
the hole (G) in the
rear bumper.
Be sure the hoist end of the extension connects into the
hoist shaft (E). The ribbed square end of the extension is
used to lower the spare tire.
4. Turn the wheel wrench (H) counterclockwise to
lower the spare tire to the ground. Continue to turn
the wheel wrench until the spare tire can be pulled
out from under the vehicle.

5-25
1. Attach the wheel wrench to the jack handle
extensions (as needed). Attach the jack handle
to the jack.2. Turn the wheel wrench clockwise to raise the jack
lift head to the lifting point.

5-26
To remove the center cap, place the chisel end of the
wheel wrench in the slot on the wheel and gently pry out.
Removing the Flat Tire and Installing the
Spare Tire
1. Use the wheel wrench to loosen all the wheel nuts.
Turn the wheel wrench counterclockwise to loosen
the wheel nuts. Don't remove the wheel nuts yet.

5-28
2. Position the jack under the vehicle.
Front Position

Front Tire Flat: Position the jack on the frame
behind the flat tire where the frame sections overlap.

Rear Tire Flat:
For a rear flat, use the
jacking pad provided
on the rear axle.
Rear Position
Turn the wheel wrench clockwise to raise the vehicle.
Raise the vehicle far enough off the ground so that
the flat tire clears the ground when it is removed and
so that the spare tire will also clear the ground when it
is installed.

5-30
5. After mounting the
spare, put the wheel
nuts back on with the
rounded end of the nuts
toward the wheel.
Tighten each wheel nut
by hand. Then use the
wheel wrench to tighten
the wheel nuts until the
wheel is held against
the hub.
Front Position
6. Turn the wheel wrench
counterclockwise to
lower the vehicle.
Lower the jack
completely.
Rear Position
7. Tighten the nuts
firmly in a crisscross
sequence as shown
by turning the wheel
wrench clockwise.

6-6
Filling Your Tank
CAUTION:
Gasoline vapor is highly flammable. It burns
violently, and that can cause very bad injuries.
Don't smoke if you're near gasoline or refueling
your vehicle. Keep sparks, flames and smoking
materials away from gasoline.
The fuel cap is located on the driver's side of your vehicle.
While refueling, hang the fuel cap by the tether using
the hook located on the inside of the filler door.
To remove the fuel cap, turn it slowly to the left
(counterclockwise).

6-7
CAUTION:
If you get gasoline on yourself and then
something ignites it, you could be badly burned.
Gasoline can spray out on you if you open the
fuel cap too quickly. This spray can happen if
your tank is nearly full, and is more likely in hot
weather. Open the fuel cap slowly and wait for
any ªhissº noise to stop. Then unscrew the cap all
the way.
Be careful not to spill gasoline. Clean gasoline from
painted surfaces as soon as possible. See ªCleaning the
Outside of Your Vehicleº in the Index.When you put the fuel cap back on, turn it to the right
(clockwise) until you hear a clicking sound. Make sure
you fully install the cap. The diagnostic system can
determine if the fuel cap has been left off or improperly
installed. This would allow fuel to evaporate into the
atmosphere. See ªMalfunction Indicator Lampº in
the Index.
NOTICE:
If you need a new fuel cap, be sure to get the
right type. Your dealer can get one for you.
If you get the wrong type, it may not fit properly.
This may cause your malfunction indicator lamp
to light and may damage your fuel tank and
emissions system. See ªMalfunction Indicator
Lampº in the Index.