2002 BUICK RANDEZVOUS flat tire

1-64
If you're using a top strap-equipped child restraint in the
second row center bench seat and need to temporarily
transport a flat tire for repair, move the child restraint to
a rear seat outboard position. See ªSecuring a Child
Restraint in a Rear Outside Seat Positionº for more on
this, including important safety information.
Once you have the top strap anchored, you'll be ready
to secure the child restraint itself. Tighten the top strap
when and as the child restraint manufacturer's
instructions say.
Your vehicle has top strap anchors already installed for
the rear seating positions. An anchor bar for a top strap
is located at the rear of the seat cushion for each second
row outboard seating position and the anchor bar for
the center position for the bench seat is located on the
floor behind the second row seats. If the vehicle has the
extended rear convenience center, you need to remove
a plastic plug and look under the convenience center to
find the anchor bar for the center position for the bench
seat. If the vehicle has a third row seat and the seatback
is upright, there is an anchor strap located between the
third row seatback and cushion to anchor the child
restraint for the second row center position bench seat.
If the vehicle has a third row seat and the seatback is
folded, there is anchor on the back of the third row
seat for the second row center position bench seat.There is also a top strap anchor for third row passenger's
side outside position. Locate the anchor symbol on the
flap of carpet behind the seat. Lift up the carpet to
access the anchor.
Captain's Chairs

1-72
4. To tighten the belt, pull up on the shoulder belt while
you push down on the child restraint. If you're using
a forward
-facing child restraint, you may find it
helpful to use your knee to push down on the child
restraint as you tighten the belt.
5. Push and pull the child restraint in different
directions to be sure it is secure.
To remove the child restraint, just unbuckle the vehicle's
safety belt and let it go back all the way. The safety belt
will move freely again and be ready to work for an adult
or larger child passenger.
Securing a Child Restraint in the
Center Rear Seat Position (Bench Seat)
The center rear seating position has a lap-shoulder
belt. To secure a child restraint in this position, you'll
use only the lap part of the belt. Disconnect the
shoulder part of the belt and store it before securing a
child restraint.
If you're using a top strap
-equipped child restraint in the
second row center bench seat and need to temporarily
transport a flat tire for repair, move the child restraint to
a rear seat outboard position. See ªSecuring a Child
Restraint in a Rear Outside Seat Positionº for more on
this, including important safety information.
Be sure to follow the instructions that came with the
child restraint. Secure the child in the child restraint
when and as the instructions say.
See the earlier part about the top strap if the child
restraint has one.

2-70
Accessory Inflator System (Option)
Your vehicle may have an air inflator. With it, you can
inflate things like bicycle tires and basketballs, and
you can also use it to bring your tires up to the
proper pressure.
The air inflator is located in the rear compartment on the
driver's side. To remove the cover, pull the tab on the
cover and pull it off.
The air inflator kit is stored in the glove box. It includes
a 20
-foot (6 m) hose with an air pressure gage and
nozzle adapters.
CAUTION:
Inflating something too much can make it
explode, and you or others could be injured. Be
sure to read the inflator instructions, and inflate
any object only to its recommended pressure.
To use your air
inflator system
do the following:
1. Turn the ignition to ACCESSORY or ON.
2. Attach the appropriate nozzle adapter, if required, to
the end of the hose that has the pressure gage.
3. Attach that end of the hose to the object you wish
to inflate.
4. Remove the protective cap covering the accessory
inflator outlet.
5. Attach the other end of the hose to the outlet.
6. Press the ON switch.

2-107
FUEL RANGE: The fuel range is an estimated
distance that your vehicle can travel on the remaining
fuel. The fuel economy used to calculate the range is
based on your driving history since the last reset of the
average speed.
FUEL USED: The fuel used display will show you how
much fuel has been used since the last time it was reset.
To reset the fuel used to zero, press and hold the SET
button while the fuel used is displayed on the DIC and
until the display goes to zero.
AVG SPEED: The average speed display will show you
your average speed from when you first started your
vehicle. To reset the average speed, press and hold the
SET button while the average speed is displayed on the
DIC and until the speed resets to your current speed.
OIL LIFE LEFT HOLD SET TO RESET: This
message displays the current percentage of the GM Oil
Life System
. Be careful not to reset this display other
than when the oil has been changed. See ªHow to Reset
the Change Engine Oil Messageº in the Index.TIRE PRESSURE: The check tire pressure system can
alert you to a large change in the pressure of one tire.
The system will not alert you before you drive that a tire
is low or flat. You must begin driving before the system
will work properly. See ªCheck Tire Pressure Systemº
in the Index.
USE SET TO SELECT ENGLISH METRIC: Yo u
can use this display to select English or metric. Press the
SET button to toggle between English or metric. The
DIC, the odometer, the trip odometer and if your vehicle
has the optional head
-up display will change.
OFF: No driver information will be displayed in this
mode. If the DIC is left in this mode for more than three
seconds, the display will turn off. Press the MODE
button to start the DIC.

4-24
The exit ramp can be curved, sometimes quite sharply.
The exit speed is usually posted.
Reduce your speed according to your speedometer, not
to your sense of motion. After driving for any distance
at higher speeds, you may tend to think you are going
slower than you actually are.
Before Leaving on a Long Trip
Make sure you're ready. Try to be well rested. If you
must start when you're not fresh
-- such as after a day's
work
-- don't plan to make too many miles that first part
of the journey. Wear comfortable clothing and shoes you
can easily drive in.
Is your vehicle ready for a long trip? If you keep it
serviced and maintained, it's ready to go. If it needs
service, have it done before starting out. Of course,
you'll find experienced and able service experts in
Buick dealerships all across North America. They'll be
ready and willing to help if you need it.Here are some things you can check before a trip:

Windshield Washer Fluid: Is the reservoir full?
Are all windows clean inside and outside?

Wiper Blades: Are they in good shape?

Fuel, Engine Oil, Other Fluids: Have you checked
all levels?

Lamps: Are they all working? Are the lenses clean?

Tires: They are vitally important to a safe,
trouble-free trip. Is the tread good enough for
long
-distance driving? Are the tires all inflated to the
recommended pressure?

Weather Forecasts: What's the weather outlook
along your route? Should you delay your trip a short
time to avoid a major storm system?

Maps: Do you have up
-to-date maps?

4-26
Hill and Mountain Roads
Driving on steep hills or mountains is different from
driving in flat or rolling terrain.If you drive regularly in steep country, or if you're
planning to visit there, here are some tips that can make
your trips safer and more enjoyable.

Keep your vehicle in good shape. Check all fluid
levels and also the brakes, tires, cooling system
and transaxle. These parts can work hard on
mountain roads.

Know how to go down hills. The most important
thing to know is this: let your engine do some of the
slowing down. Shift to a lower gear when you go
down a steep or long hill.
CAUTION:
If you don't shift down, your brakes could get
so hot that they wouldn't work well. You would
then have poor braking or even none going
down a hill. You could crash. Shift down to let
your engine assist your brakes on a steep
downhill slope.

4-34
Loading Your Vehicle
The Certification/Tire label is found on the rear edge of
the driver's door.
The label shows the size of your original tires and the
inflation pressures needed to obtain the gross weight
capacity of your vehicle. This is called the Gross Vehicle
Weight Rating (GVWR). The GVWR includes the
weight of the vehicle, all occupants, fuel and cargo.The Certification/Tire label also tells you the maximum
weights for the front and rear axles, called the Gross
Axle Weight Rating (GAWR). To find out the actual
loads on your front and rear axles, you need to go to a
weigh station and weigh your vehicle. Your dealer can
help you with this. Be sure to spread out your load
equally on both sides of the centerline.
Never exceed the GVWR for your vehicle or the GAWR
for either the front or rear axle.
CAUTION:
Do not load your vehicle any heavier than the
GVWR, or either the maximum front or rear
GAWR. If you do, parts on your vehicle can
break, and it can change the way your vehicle
handles. These could cause you to lose control
and crash. Also, overloading can shorten the life
of your vehicle.

4-40 Total Weight on Your Vehicle's Tires
Be sure your vehicle's tires are inflated to the upper
limit for cold tires. You'll find these numbers on the
Certification/Tire Label at the rear edge of the driver's
door, or see ªTire Loadingº in the Index. Then be sure
you don't go over the GVW limit for your vehicle,
including the weight of the trailer tongue.
Hitches
It's important to have the correct hitch equipment.
Crosswinds, large trucks going by and rough roads are
a few reasons why you'll need the right hitch. Here are
some rules to follow:

If you'll be pulling a trailer that, when loaded, will
weigh more than 2, 000 lbs. (900 kg), be sure to use
a properly mounted, weight
-carrying hitch and sway
control of the proper size. This equipment is very
important for proper vehicle loading and good
handling when you're driving.

Will you have to make any holes in the body of your
vehicle when you install a trailer hitch?
If you do, then be sure to seal the holes later when
you remove the hitch. If you don't seal them, deadly
carbon monoxide (CO) from your exhaust can get
into your vehicle. See ªCarbon Monoxideº in the
Index. Dirt and water can, too.
Safety Chains
You should always attach chains between your vehicle
and your trailer. Cross the safety chains under the tongue
of the trailer to help prevent the tongue from contacting
the road if it becomes separated from the hitch.
Instructions about safety chains may be provided by the
hitch manufacturer or by the trailer manufacturer. Follow
the manufacturer's recommendation for attaching safety
chains and do not attach them to the bumper. Always
leave just enough slack so you can turn with your rig.
Never allow safety chains to drag on the ground.
Trailer Brakes
If your trailer weighs more than 1,000 lbs. (450 kg)
loaded, then it needs its own brakes
-- and they must be
adequate. Be sure to read and follow the instructions for
the trailer brakes so you'll be able to install, adjust and
maintain them properly.
Because you have anti
-lock brakes, do not try to tap
into your vehicle's brake system. If you do, both brake
systems won't work well, or at all.