2002.5 Peugeot 307 Break change wheel

09-09-2002
3YOUR 307 AT A GLANCE
1Speaker (tweeter).
2 Side window demisting vent.
3 Windscreen demisting vents.
4 Passenger air bag.
5 Brightness sensor.
6 Multifunction display.
7 Alarm button.
8 Central locking button.
9 Hazard warning lights
switch.
10 Lights and direction indica
tors stalk.
11 Instrument dials.
12 Steering wheel adjustment
control.
13 Windscreen wash/wipe
stalk.
Trip computer stalk.
14 Driver's air bag.
Horn. 15
Radio remote control stalk.
16 Headlamp height
adjustment.
17 Electric mirror controls.
Window controls.
Rear window locking
control.
18 Steering lock and ignition.
19 Cruise control switch.
20 12 V accessories socket.
21 Coin storage
Passenger air bag
disarming switch*.
22 Rubbish container.
23 Can holder.
24 Handbrake.
25 Rear footwell heating vent.
26 Gear lever.
27 Front ash tray.
28 Heating/air conditioning
controls. 29
CD changer.
30 RB3, RD3 or RT3
audio equipment.
31 Central adjustable heating/
ventilation vent and air flow
regulation.
32 Side adjustable heating/
ventilation vent and air flow
regulation.
33 Fuse box.
34 Glove box.
35 Bonnet opening control.
* According to destination.

09-09-2002
YOUR 307 IN DETAIL79
The menu ''Guidance options'' pro
vides access to the following func
tions:
changing of the route calculation criteria,
voice synthesis adjustment of guid ance messages,
description of the information relat ing to the navigation CDRom,
management of the addresses stored in the directory.
Guidance options
The last criteria used are displayed.
Select a criterion from the list, then
validate by pressing the dial.
When the criterion of your choice has
been selected, select the
"OK"func
tion then confirm by pressing the
dial.
Adjusting the voice synthesiser
Select the type of voice "male"or
"female" , after inserting the configu
ration CDROM.
Adjust the volume of the voice syn
thesis by turning the dial, then vali
date by pressing the dial.
Note: the volume can also be adjust
ed during a message, using the
audio/telephone button on the steer
ing wheel control. Management of the directory
This function enables you to rename
or delete an address stored in the
directory.
Select the description corresponding
to the stored address to be changed.
Select the
"Delete" function or the
"Rename" function, then confirm by
pressing the dial.
Select the "OK" function, then con
firm by pressing the dial to record the
changes made.
Stopping / Resuming guidance
"Stop guidance"
During guidance, select this function
then validate.
"Resume guidance"
In the absence of guidance select
this function then validate to activate
guidance to the last destination pro
grammed.
Calculation criteria

09-09-2002
CHANGING A WHEEL
(SALOON)
Parking the vehicle Park the vehicle on level, stable
and nonslippery ground.
Apply the handbrake, switch off
the ignition and engage first or
reverse gear (position Pfor the
automatic gearbox) .
Access to the spare wheel and
the jack in the boot Lift the floor using the handle and
secure it by hooking the cords to
the hooks of the parcel shelf. Tools
The following tools are located in a
polystyrene holder in the centre of
the spare wheel:
1
Wheelbrace.
2 Centralising tool.
3 Removable chock.
4 Jack with handle.
5 Removable towing eye.
6 Alloy wheel bolt trim remover. Removing the wheel
Place the holder and the chock
3(or chock 3 on its own if neces
sary) under the wheel diagonally
opposite to the one to be
changed.
Remove the trim, using the
wheelbrace 1, pulling at the valve
passage hole.
Loosen the wheel bolts (for vehi
cles fitted with alloy wheels,
remove the chrome trim first. See
paragraph on 'Special features of
alloy wheels').
PRACTICAL INFORMATION
142

09-09-2002
Place the jack 4in contact with one
of the four locating points Aon the
subframe, (the one which is clos
est to the wheel to be changed).
Extend the jack 4until its base is in
contact with the ground. Ensure
that the centre line of the base of
the jack is straight above the locat
ing point A.
Raise the vehicle.
Unscrew the bolts and remove the
wheel.
Fitting a wheel
Position the wheel using the cen
tralising tool to assist you.
Tighten the bolts by hand and
remove the centralising tool.
Partly tighten the bolts using the
wheelbrace 1.
Fold the jack 4 and remove it.
Fully tighten the bolts using the
wheelbrace 1.
Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it
on using the palm of the hand.
Put the tools and the wheel back
in the boot.
Note: a diagram on the holder indi
cates the location of the tools. .
Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact.
PRACTICAL INFORMATION 143
For your safety, always
change the wheel:
on level, stable, nonslippery ground,
with the handbrake on and the ignition switched off,
with first or reverse gear engaged (position Pfor the
automatic gearbox),
with the vehicle chocked.
Never go underneath a vehicle
that is supported only by a jack
(use a ramp)
After changing the wheel:
have the tightening of the bolts and the tyre pressure checked
by a PEUGEOT dealer as soon
as possible.
have the punctured tyre repaired and refit it to the vehicle
as soon as possible.

PRACTICAL INFORMATION145

Detach the wheel/holder assem
bly from the rear of the vehicle.
Take out the notched hook to
release the wheel, as shown in
the illustration.
Removing the wheel Slide the holder cover to gain
access to the tools.
Place the chock 7under the
wheel diagonally opposite to the
one to be changed.
Remove the trim, using the
wheelbrace 1, pulling at the
valve passage hole (for vehicles
fitted with steel wheels).
Loosen the wheel bolts (see
§ "Special features of alloy
wheels" for vehicles fitted with
alloy wheels).
Note: you can use the other end
of the tool 6to unscrew the
wheel bolts.
Place the jack 4in contact with
one of the four locating points A
on the subframe; the closest
possible to the wheel to be
changed.
Extend the jack 4until its base is
in contact with the ground.
Ensure that the centre line of the
base of the jack is straight above
the locating point A.
Raise the vehicle.
Remove one bolt and position the
centralising tool 5in its place.
Unscrew the other bolts and
remove the wheel.
09-09-2002

09-09-2002
PRACTICAL INFORMATION
146
Fitting a wheel Position the wheel using the cen
tralising tool 5to assist you.
Tighten the bolts by hand and
remove the centralising tool 5.
Partly tighten the bolts using the
wheelbrace 1.
Fold the jack 4 and remove it.
Fully tighten the bolts using the
wheelbrace 1.
Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it
on using the palm of the hand.
Put the corresponding tools in the
holder and secure its cover.
Place the holder on the ground
and align the spare wheel on it.
Pass the notched hook into the
holder cover.
Refit the wheel under the vehicle
tightening the winch control nut
using the wheelbrace 1.
Fully tighten and check that the
wheel is horizontally flush
against the rear floor .
Close the flap using the lug to
lock the winch.
Store the rest of the tools in the
righthand trim of the boot. For your safety, always
change the wheel:
on level, stable, nonslippery ground,
with the handbrake on and the ignition switched off,
with first or reverse gear engaged (position Pfor the
automatic gearbox),
with the vehicle chocked.
Never go underneath a vehicle
that is supported only by a jack
(use a ramp).
Never refit the holder under the
vehicle without the spare
wheel.
After changing the wheel:
have the correct positioning of the punctured wheel, the tight
ening of the bolts and the tyre
pressure checked by a
PEUGEOT dealer as soon as
possible.
have the punctured tyre repaired and refit it to the vehicle
as soon as possible.
have the correct positioning of the spare wheel checked by a
PEUGEOT dealer.

09-09-2002
PRACTICAL INFORMATION
150
Number plate lights
(W 5 W) Insert a thin screwdriver into one
of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Change the faulty bulb.

Remove the bulb holder pressing
on the tabs A,
Change the faulty bulb.
Note: f necessary, use the wheel
brace to remove the nuts.
When refitting, take care to position
the bulb holder and the light correct
ly. Third brake light (saloon)
4 W 5 W bulbs
Remove the tailgate upper trim
carefully by unclipping it on either
side, perpendicular to its direc
tion of engagement.
Insert a screwdriver into the two
outer holes B to press on the two
tabs C.
Push the light unit outwards while
maintaining the pressure on the
tabs.
Pull the light unit outwards while
tilting it.
Change the faulty bulb.
When refitting, ensure that the
light unit tabs are engaged cor
rectly and that the tailgate upper
trim has been put back in place
correctly.
Rear lights (estate)
1 Brake lights (P 21 W).
2 Side lights (R 5 W).
3 Direction indicators (P 21 W).
4 Reversing light (P 21 W),
left side.
Fog lamp (P 21 W), right side.
These 5 bulbs are changed by
removing the light: Remove the light fixing nut inside
the boot,
Remove the light fixing nut out
side the boot,
Remove the light,
Unclip the harness,

09-09-2002
PRACTICAL INFORMATION
150
Number plate lights
(W 5 W) Insert a thin screwdriver into one
of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Change the faulty bulb.

Remove the bulb holder pressing
on the tabs A,
Change the faulty bulb.
Note: f necessary, use the wheel
brace to remove the nuts.
When refitting, take care to position
the bulb holder and the light correct
ly. Third brake light (saloon)
4 W 5 W bulbs
Remove the tailgate upper trim
carefully by unclipping it on either
side, perpendicular to its direc
tion of engagement.
Insert a screwdriver into the two
outer holes B to press on the two
tabs C.
Push the light unit outwards while
maintaining the pressure on the
tabs.
Pull the light unit outwards while
tilting it.
Change the faulty bulb.
When refitting, ensure that the
light unit tabs are engaged cor
rectly and that the tailgate upper
trim has been put back in place
correctly.
Rear lights (estate)
1 Brake lights (P 21 W).
2 Side lights (R 5 W).
3 Direction indicators (P 21 W).
4 Reversing light (P 21 W),
left side.
Fog lamp (P 21 W), right side.
These 5 bulbs are changed by
removing the light: Remove the light fixing nut inside
the boot,
Remove the light fixing nut out
side the boot,
Remove the light,
Unclip the harness,