2002.5 Peugeot 206 CC Owner's Manual

YOUR 206 CC IN DETAIL91
In the
"OFF" position, the passenger
air bag will not be triggered in the event of an impact. As soon as the child seat is removed, turn the air bag slot to the "ON"posi-
tion to re-activate the air bag and thusensure the safety of your passenger inthe event of an impact. Operating check This is confirmed by an indicator light, accompanied by an audible signaland a message on the multifunction
display. With the ignition on (2nd notch), illumi- nation of this warning light accompaniedby an audible signal and the message"Passenger air bag disarmed" on the
multifunction display, indicates that thepassenger air bag is disarmed (switch inthe "OFF" position).SIDE AIRBAGS These are incorporated into the frame of the front seat back, on the doorside. They are deployed independently of each other depending on which sidethe collision occurs, in collisions whichcould cause injury to the chest, theabdomen or the head. Operating check
This is confirmed by an indicator lighton the instrument panel. It comes on for six seconds, each time the ignition is switched on. If the indicator light:
Ð does not light up when the ignition is switched on, or
Ð does not go out after six seconds or,
Ð flashes for five minutes then stays on.
Contact a PEUGEOT dealer.
07-10-2002

07-10-2002
YOUR 206 CC IN DETAIL
92
For the front and side air bags to be fully effective, observe the following safety rules:
¥ Wear a correctly adjusted seat belt.
¥ Sit in a normal upright position (passengers must not place their feet on the fascia).
¥ Ensure there is nothing between the occupants of the front seats and the air bags. This could hamper the operation of the air bags or injure the occupants.
¥ All work on the air bag systems is strictly forbidden unless it is carried out by qualified personnel of the PEUGEOT network.
¥ After an accident or if the vehicle has been stolen or broken into, have the air bag systems checked.
¥ The air bag systems have been designed to be fully operational for 10 years after the vehicle has been registered. For greater safety, have them checked by a PEUGEOT dealer within ten years following the initial purchase of the vehicle.
Front air bags
¥ Do not drive holding the steering wheel by its spokes or resting your hands on the centre part of the wheel.
¥ Never remove or pierce the steering wheel or hit it violently.
¥ Smoke as little as possible; deployment of the air bags can cause burns or the risk of injury from a cigarette or pipe. Side air bags
¥ Do not fix or glue anything to the front seat backs. This could cause injury to the chest or arms when the side air bag inflates.
¥ Do not sit with the upper part of the body any nearer to the door than necessary.
¥ Use only approved covers on the front seats. Contact your PEUGEOT dealer.

07-10-2002
PRACTICAL INFORMATION93
1 -
Power steering reservoir.
2 - Windscreen wash reservoir.
3 - Coolant reservoir. 4 -
Brake fluid reservoir.
5 - Battery.
6 - Air filter. 7 -
Dipstick.
8 - Engine oil filler cap.
1.6 litre 16V engine

07-10-2002
PRACTICAL INFORMATION
94
1 -
Power steering reservoir.
2 - Wndscreen wash reservoir.
3 - Coolant reservoir. 4 -
Brake fluid reservoir.
5 - Battery.
6 - Air filter. 7 -
Dipstick.
8 - Engine oil filler cap.
2 litre 16V engine

07-10-2002
PRACTICAL INFORMATION95
CHECKING LEVELS Engine oil Oil level check Carry out this check regularly and top up between oil changes
; the
maximum consumption is 0.5 litre per600 miles (1000 km). The check must be carried out with the vehicle level and the engine cold..
There are two levelmarks on the dipstick: A= maximum.
B = minimum. Viscosity grade selectionThe oil selected must always meet the manufacturer's requirements. Oil filter Change the cartridge regularly in accordance with the recommenda-tions of the servicing schedule. Used oil
Avoid any prolonged contact of used oil with the skin. Do not discard used oil down drains or onto the ground.
To maintain the reliability of the engines and emission control sys-tems, the use of additives in the oil isprohibited. Brake fluid reservoir
Ð The level must always be above the
DANGER mark on the tank.
Ð In the event of a significant drop in the level, contact a PEUGEOT deal-
er immediately. Fluid change
Ð Always to be carried out at the inter-
vals given in the manufacturer's ser- vicing schedule.
Ð Use fluids approved by the manu- facturer which comply with DOT4standards.
Coolant reservoir Use a coolant approved by the manu-
facturer. When the engine is warm, the coolant
temperature is controlled by the fan.This may operate with the ignition key
removed. Therefore, as the coolingcircuit is pressurised, wait at least an
hour after switching off the enginebefore carrying out any work.
In the event of a breakdown and to
avoid any risk of burns, unscrew thecap two turns to let the pressure drop.When the pressure has dropped,remove the cap and top up the level.
Oil change: in accordance with the
manufacturer's servicing schedule.
Ð Dipstick: never exceed the maximum mark A.
Ð Instrument dial gauge.

07-10-2002
PRACTICAL INFORMATION
96
Power steering reservoir
Open the reservoir, with the engine
cold. The level should always beabove the MINI mark, close to theMAXI mark.
Windscreen wash reservoir For best quality cleaning and for your
safety, we recommend that you useproducts approved by PEUGEOT(capacity 2.8 litres). Battery
At the start of winter, have your battery
checked by a PEUGEOT dealer. Air filter Regular replacement of the filter ele- ment is essential. If you drive in verydusty conditions, change it twice asoften. Brake pads Brake pad wear depends on the style of driving, in particular for vehicleswhich are used in town, for short jour-neys. It may be necessary to checkthe thickness of the pads evenbetween services. Manual gearbox This does not need an oil change: have the level checked by a PEU-
GEOT dealer according to the manu-facturer's servicing schedule. Autoadaptive automatic gearbox This does not need an oil change: have the level checked by a PEU-
GEOT dealer according to the manu-facturer's servicing schedule.Only use products appro-
ved by PEUGEOT.
To ensure best perfor-mance from components
as important as the power steeringand the braking system, PEUGEOTselects and offers quite specificproducts.

07-10-2002
PRACTICAL INFORMATION97
PUNCTURES Because this version does not pos- sess a spare wheel, you have twoaerosols for temporary tyre repairsstored in an insulated storage box
1
secured by a strap to the right-handside of the boot. Using a repair aerosol (See also the instructions on the aerosols). 
If possible remove the foreign body which caused the puncture.
 Position the wheel so that the valveis at the 2 o'clock or 10 o'clock posi-tion.
 Shake the aerosol vigorously
before use. (In very cold weather,warm the aerosol for a few minutesin your hands).
 In one hand hold the valve.
 With the other, firmly push thespray end of the aerosol onto thevalve, keeping it centralised.
 Maintain the pressure firmly for oneminute, then immediately drive at
moderate speed to the nearest
garage. Aersosols enable a tempo-rary repair to be carried out(maximum speed 50 mph(80 km/h)).
After use, it is necessary to repairthe tyre. Because the aerosols are pres- surised, they must not be exposed
to a temperature higher than 50 ¡C. Keep them away from heat in their insulated storage box.

07-10-2002
PRACTICAL INFORMATION
98
CHANGING A WHEEL 
Park the vehicle on level, stable
ground which is not slippery.
 Apply the handbrake, engage first
gear or reverse (position Pon the
automatic gearbox) and switch offthe ignition.
 Chock the rear of the wheel withshim 2diagonally opposite the
wheel to be changed.
Tools for changing a wheel 1 - Wheelbrace fitted to the lining of the boot on the rear right side.
2 - Shim stored in the jack bag.
3 - Jack (in a bag secured by two straps,on the right-hand side of the boot).
4 - Tool for removing wheel bolt trims(located on the boot rear right innerpanel). Removing the wheel 
Remove the wheel trim using the wheelbrace 1by pulling next to the valve.
 Loosen the wheel bolts (for vehicles fitted with alloy wheels, remove the chrome wheel bolts first; see "Features of alloy wheels", following page).
 Position the jack 3at one of the four locations Aunderneath the vehicle, as
close as possible to the wheel to be changed. Ensure that the entire surface ofthe jack base plate is in contact with the ground.
 Extend the jack 3.
 Remove the bolts and release the wheel.