Page 76 of 372
4-17
1. On command four-wheel drive switch “2WD/4WD”
1.Contacteur de commande du mode de traction
“2WD/4WD”
1. Interruptor de modo de tracción “2WD/4WD”
EBU00061
On command four-wheel drive switch
“2WD/4WD”
To change from two-wheel drive (2WD) to
four-wheel drive (4WD), stop the ATV and set
the switch to the 4WD position.
To change from four-wheel drive (4WD) to
two-wheel drive (2WD), stop the ATV and set
the switch to the 2WD position.
WARNING
Always stop the ATV before changing from
2WD to 4WD or from 4WD to 2WD. The ATV
handles differently in 2WD than in 4WD in
some circumstances. Changing from 2WD to
4WD or vice-versa while moving may cause
the ATV to unexpectedly handle differently.
This could distract the operator and increase
the risk of losing control and an accident.
Page 78 of 372
4-19
1. Throttle lever
1. Levier d’accélération
1. Palanca de aceleración
EBU00063
Throttle lever
Once the engine is running, movement of the
throttle lever will increase the engine speed.
Regulate the speed of the machine by varying
the throttle position. Because the throttle is
spring-loaded, the machine will decelerate,
and the engine will return to an idle any time
the hand is removed from the throttle lever.
Before starting the engine, check the throttle to
be sure it is operating smoothly. Make sure it
returns to the idle position as soon as the lever
is released.
WARNING
Malfunction of the throttle could make it diffi-
cult to speed up or slow down when you need
to. This could cause an accident. Check the op-
eration of the throttle lever before you start
the engine. If the throttle does not work
smoothly, check for the cause. Correct the
problem before riding the ATV or consult a
Yamaha dealer.
Page 80 of 372
4-21
1. Locknut 2. Adjusting bolt a. 12 mm
1. Contre-écrou 2. Boulon de réglage
1. Contratuerca 2. Perno de ajuste
EBU00565
Speed limiter
The speed limiter keeps the throttle from fully
opening, even when the throttle lever is
pushed to the maximum. Screwing in the ad-
juster limits the maximum engine power avail-
able and decreases the maximum speed of the
ATV.
WARNING
Improper adjustment of the speed limiter and
throttle could cause throttle cable damage or
improper throttle operation. You could lose
control, have an accident or be injured. Do not
turn the speed adjuster out more than 12 mm
or the throttle cable could be damaged. Al-
ways make sure the throttle lever free play is
adjusted to 3 ~ 5 mm. See page 8-49.
Page 86 of 372
4-27
EBU00075
Parking brake
Use the parking brake when you have to start
the engine or park the machine, especially on a
slope. Apply the rear brake lever and push
down the lock plate to apply the parking brake.
Squeeze the rear brake lever to release the
parking brake.
WARNING
●Always set the parking brake before start-
ing the engine. The ATV could start mov-
ing unexpectedly if the parking brake is
not applied. This could cause loss of con-
trol or a collision.
●Always be sure you have released the
parking brake before you begin to ride.
The brake could overheat if you ride the
ATV without releasing the parking brake.
You could lose braking performance
which could cause an accident. You could
also wear out the brakes prematurely.
1. Lock plate
1. Verrou
1. Placa de bloqueo
Page 88 of 372
4-29
EBU00087
Drive select lever
The drive select lever is used to shift your ma-
chine into neutral, high, low or reverse. Refer
to page 6-11 for the drive select lever opera-
tion.
EBU00591
Recoil starter
Firmly grasp the handle and pull slightly until
engagement can be felt. Then pull forcefully,
being careful not to pull the rope all the way
out.
WARNING
Put the transmission in neutral and set the
parking brake before starting the engine or the
ATV could start to move unexpectedly, which
could cause an accident.
1. Drive select lever
1. Levier de présélection
1. Palanca de selección de marcha
1. Recoil starter
1. Lanceur à réenroulement
1. Arranque por tracción de cable
Page 113 of 372
5-2
5
5
5
5
5
5
5
5
9
50
55
WARNING
Always inspect your ATV each time you use it to make sure the ATV is in safe operating condition.
Always follow the inspection and maintenance procedures and schedules described in the Own-
er’s Manual. Failure to inspect increases the possibility of an accident or equipment damage.
Page 120 of 372
5-9
3. Brake fluid leakage
Check to see if any brake fluid is leaking
out of the hose, joint or master cylinder of
the front brake. Apply the brake firmly for
one minute. If the lever moves slowly in-
ward, there may be a leak in the brake sys-
tem. If there is any leakage, the brake
system should be inspected by a Yamaha
dealer.
4. Brake operation
Test the brakes at slow speed after start-
ing out to make sure they are working
properly. If the brakes do not provide
proper braking performance, inspect the
brakes for wear. (See page 8-51.)
WARNING
Always check the brakes at the start of every
ride. Do not ride the ATV if you find any prob-
lem with the brakes or you could lose braking
ability, which could lead to an accident. If a
problem cannot be corrected by the adjust-
ment procedures provided in this manual,
have the ATV inspected by a Yamaha dealer.
Page 124 of 372
5-13
1. Fuel level 2. Filler tube
1. Niveau de carburant 2. Tube de remplissage
1. Nivel de combustible 2. Tubo del relleno
WARNING
●Do not overfill the fuel tank. Fuel expands
when it heats up. If the fuel tank is over-
filled, fuel could spill out due to heat from
the engine or the sun.
●Be careful not to spill fuel, especially on
the engine or exhaust pipe which can
cause a fire and severe injury. Wipe up
any spilled fuel immediately.
●Do not refuel right after the engine has
been running and is still very hot.
●Be sure the fuel tank cap is closed secure-
ly.