1
2
3
4
5
67
8
9
7-2
MOTORCYCLE CARE AND STORAGE
8Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.
8Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric com-
ponents (couplers, connec-
tors, instruments, switches
and lights), breather hoses
and vents.8For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure that it
does not leave any marks. If
the windshield is scratched,
use a quality plastic polishing
compound after washing.
After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas.
Stubborn dirt and insects will come
off more easily if the area is covered
with a wet cloth for a few minutes
before cleaning.After riding in the rain, near the sea
or on salt-sprayed roadsSince sea salt or salt sprayed on
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.NOTE:
Salt sprayed on roads in the winter
may remain well into spring.1.Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
cCDo not use warm water since it
increases the corrosive action of
the salt.2.After drying the motorcycle,
apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, sur-
faces to prevent corrosion.
5JX-9-E1 9/27/00 10:45 AM Page 73
7-3
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
67
8
9After cleaning
1.Dry the motorcycle with a
chamois or an absorbing cloth.
2.Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3.Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally
induced discoloring of stainless-
steel exhaust systems can be
removed through polishing.)
4.To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, includ-
ing chrome- and nickel-plated,
surfaces.
5.Use spray oil as a universal
cleaner to remove any remaining
dirt.
6.Touch up minor paint damage
caused by stones, etc.7.Wax all painted surfaces.
8.Let the motorcycle dry complete-
ly before storing or covering it.
EWA00001
w8Make sure that there is no oil
or wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires
with warm water and a mild
detergent.
8Before operating the motorcy-
cle test its braking perfor-
mance and cornering behav-
ior.
ECA00013
cC8Apply spray oil and wax spar-
ingly and make sure to wipe
off any excess.
8Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
8Avoid using abrasive polish-
ing compounds as they will
wear away the paint.NOTE:
Consult a Yamaha dealer for advice
on what products to use.
5JX-9-E1 9/27/00 10:45 AM Page 74
SPECIFICATIONS
8-3
8
Maximum load*183 kg
Air pressure (cold tire)
up to 90 kg load*
Front
175 kPa (1.75 kg/cm
2, 1.75 bar)
Rear
200 kPa (2.00 kg/cm
2, 2.00 bar)
90 kg loadÐmaximum
load*
Front
225 kPa (2.25 kg/cm
2, 2.25 bar)
Rear
225 kPa (2.25 kg/cm
2, 2.25 bar)
*Total weight of rider, passenger, cargo and accessories
Wheels
Front
TypeSpoke wheel
Size18 ´1.60
Rear
TypeSpoke wheel
Size15 M/C ´MT 3.00
Brakes
Front
TypeSingle disc brake
OperationRight hand
FluidDOT 4Rear
TypeDrum brake
OperationRight foot
Suspension
Front
TypeTelescopic fork
Rear
TypeSwingarm
Shock absorber/spring
Front
TypeCoil spring / oil damper
Rear
TypeCoil spring / oil damper
Wheel travel
Front140 mm
Rear100 mm
Electrical system
Ignition systemTransistorized coil ignition
(digital)
Charging system
TypeA.C. magneto
Standard output14 V, 23 A @ 5,000 r/min
5JX-9-E1 9/27/00 10:45 AM Page 79
