2001 TOYOTA PRIUS warning light

H15525
Combination Meter
Instrument Panel J/B
10A ACC
ACC Relay
5A AM1
W±G L15
C10
16
C10
5
C11
GR±RGR±R
W±BB±Y 9
2A
2
2D
8
2A
1
2H
8
2C
3
2B53
128
2K4
2B 1
2E3
A18LA
1
F11C
J27
Fl Block No. 1
23P±LW 1
F13
1 B±GL
GR±R
BBC
J28AB
A
J11
J/C
Battery F18
FL
Block
No. 2DLC3
DC/DC100A
J/C
I15 Ignition S/W
120A
MAINAirbag Sensor
Assembly
B±Y6
ID J26
J/C
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±637
2001 PRIUS (RM778U)
SRS Warning Light Circuit Malfunction
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the ignition switch is
turned from the LOCK position to ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to inform the driver of the abnormality.
When terminals Tc and CG of the DLC3 are connected, the DTC is displayed by blinking the SRS warning
light.
WIRING DIAGRAM
DI7QT±01

AB0117H01293H01295
Airbag Sensor Assembly
LOCK
DI±638
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
2001 PRIUS (RM778U)
INSPECTION PROCEDURE
Always lights up, when ignition switch is in LOCK position
1 Prepare for inspection (See step 1 on page DI±629).
2 Does SRS warning light turn off?
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect negative (±) terminal cable from the battery,
and wait at least for 90 seconds.
(c) Disconnect the airbag sensor assembly connector.
(d) Connect negative (±) terminal cable to the battery.
CHECK:
Check operation of SRS warning light.
NO Check SRS warning light circuit or terminal A/B
circuit of DLC3.
YES
Replace airbag sensor assembly.

N14677
Fuse
AB0119H01300
H01301
Airbag Sensor Assembly
ON
LA
(+)
(±)
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±639
2001 PRIUS (RM778U)
Does not light up, when ignition switch is turned to ON
1 Check AM2 Fuse.
PREPARATION:
Remove the AM2 fuse.
CHECK:
Check continuity of the AM2 fuse.
OK:
Continuity
HINT:

Fuse may be burnt out even if it appears to be OK during
visual inspection.

If fuse is OK, install it.
NG Go to step 4.
OK
2 Prepare for inspection (See step 1 on page DI±629).
3 Check SRS warning light circuit.
PREPARATION:
(a) Disconnect the airbag sensor assembly connector.
(b) Connect negative (±) terminal cable to the battery.
(c) Turn the ignition switch to ON.
CHECK:
Measure the voltage between body ground and LA terminal of
the harness side connector of the airbag sensor assembly.
OK:
Voltage: 10 ± 14 V
NG Check combination meter or repair SRS warn-
ing light circuit.
OK
Replace airbag sensor assembly.

DI±640
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
2001 PRIUS (RM778U)
4 Is new AM2 fuse burnt out again?
NO Using simulation method, reproduce malfunc-
tion symptoms (See page IN±30).
YES
Check harness between AM2 fuse and SRS
warning light.

H15526
J11
J/C AW±B 2KW±BJ24
J/C
W±BDLC3
P±BJ26
J/C
P±B
Tc
8 2D 8AA
413 CGTc
E
E19
A18
Instrument Panel J/BAirbag Sensor
Assembly
ID
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±641
2001 PRIUS (RM778U)
Tc Terminal Circuit
CIRCUIT DESCRIPTION
By connecting terminals Tc and CG of the DLC3 the airbag sensor assembly is set in the DTC output mode.
The DTCs are displayed by blinking the SRS warning light.
WIRING DIAGRAM
DI6Q0±06

AB0117AB0119H15218H15700
LOCK
ON
AB0119H10688H10654
ON
CG
Tc
(+) (±)
DI±642
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
2001 PRIUS (RM778U)
INSPECTION PROCEDURE
If the DTC is not displayed, do the following troubleshooting.
1 Does SRS warning light light up for approx. 6 seconds?
PREPARATION:
Check operation of the SRS warning light after ignition switch
is turned from LOCK position to ON position.
NO Check SRS warning light system (See page
DI±632).
YES
2 Check voltage between terminals Tc and CG of DLC3.
PREPARATION:
Turn the ignition switch to ON.
CHECK:
Measure the voltage between terminals Tc and CG of DLC3.
OK:
Voltage: 10 ± 14 V
OK Go to step 4.
NG

AB0119H10689H10656
ON
Tc
(+) (±)
AB0117 AB0119H01302H12918
LOCK
ON
Airbag Sensor Assembly
Tc
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±643
2001 PRIUS (RM778U)
3 Check voltage between terminal Tc of DLC3 and body ground.
CHECK:
Measure the voltage between terminal Tc of DLC3 and body
ground.
OK:
Voltage: 10 ± 14 V
OK Check harness between terminal E1 of DLC3
and body ground.
NG
4 Check airbag sensor assembly.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect negative (±) terminal cable from the battery,
and wait at least for 90 seconds.
(c) Disconnect the airbag sensor assembly connector.
(d) Insert service wire into terminal Tc from back side as
shown in the illustration.
(e) Connect the airbag sensor assembly connector with ser-
vice wire.
(f) Connect negative (±) terminal cable to the battery.
(g) Turn the ignition switch to ON and wait at least for 20 se-
conds.
(h) Connect service wire of terminal Tc to body ground.
CHECK:
Check operation of the SRS warning light.
OK:
SRS waning light comes on.
NOTICE:
Pay due attention to the terminal connecting position to
avoid a malfunction.
OK Check harness between the airbag sensor as-
sembly and DLC3.
NG
Replace airbag sensor assembly.

DI7XS±01
DI±674
± DIAGNOSTICSCOMBINATION METER SYSTEM
2001 PRIUS (RM778U)
PROBLEM SYMPTOMS TABLE
TROUBLESHOOTING:
Flow chart No.SymptomSee page
1Check the communication between the combination meter and the multiplex com-
munication circuit.DI±671
2The whole meter does not functionDI±672
3The margin of error in speedometer is large. Or it remains as 0 mph.DI±673
4Fuel receiver gauge is inoperative or improper.DI±674
5Indicators or warning lights do not light up.DI±676
Fuel gauge:
SymptomSuspect AreaSee page
Displayed level is higher or lower than the actual level.1. Inclination sensor resetting
2. Body ECUBE±47
IN±41
General:
SymptomSuspect area
Meter display does not properly function.3. Combination meter ECU
Entirely black screen appears.1. Fuse
2. Wire harness and connector
3. Combination meter ECU
Turning the light control switch ON does not dim the light.1. Illumination switch
2. Wire harness and connector
3. Combination meter ECU
Brightness cannot be changed by the illumination switch operation.1. Illumination switch
2. Wire harness and connector
3. Combination meter ECU
Speedometer:
SymptomSuspect area
Improper display (Remained as 0 km/h)1. Accessory that utilizes vehicle speed signals
2. Brake ECU
3. Combination meter ECU
4. Wire harness and connector
Speedometer only does not light up.1. Combination meter ECU
Abnormal display (Incomplete numbers displayed)1. Combination meter ECU
DIsplayed value changes frequently or sharply.1. Accessory that utilizes vehicle speed signals
2. Brake ECU
3. Combination meter ECU
4. Wire harness and connector
Margin of error in speedometer is large.1. Accessory that utilizes vehicle speed signals
2. Brake ECU
3. Combination meter ECU
4. Wire harness and connector
ODO/TRIP Meter:
SymptomSuspect area
ODO/TRIP only does not light up.1. Combination meter ECU
Abnormal display (Incomplete number displayed)1. Combination meter ECU
Both meters do not integrate values. (When speedometer is normal)1. Combination meter ECU
Trip meter only does not integrate values.1. ODO/TRIP switch
2. Combination meter ECU