2001 SUZUKI GRAND VITARA clutch

AUTOMATIC TRANSMISSION (4 A/T) 7B1-51
DISASSEMBLY
1) After removing retaining ring (1), remove direct clutch input
hub (2) and forward clutch hub (3).
2) Remove bearing race and thrust bearing.
3) Install direct clutch input hub (1) and retaining ring (2).
4) Install forward clutch (2) to O/D case (1). Apply 4 – 8 kg/cm
2
air pressure into fluid hole at the right of cut in O/D case and
measure movement of forward clutch piston.
If measured value is not within standard range, use either
1.8 mm (0.071 in.) or 2.0 mm (0.079 in.) clutch disc to adjust
it to standard value.
Standard forward clutch piston movement :
1.40 – 1.70 mm (0.056 – 0.067 in.)
1. Thrust bearing No. 2
2. Thrust forward clutch bearing
3. Thrust rear race

7B1-52 AUTOMATIC TRANSMISSION (4 A/T)
5) Remove retaining ring (1) and then remove direct clutch
input hub.
6) Remove retaining ring and then remove all clutch discs.
7) Using special tool and hydraulic press, compress forward
clutch piston return spring and remove retaining return
spring.
Special tool
(A) : 09926-98310
8) Remove forward clutch piston return spring.
9) Install forward clutch to O/D case. Blow low pressure air into
fluid hole at the right of cut in O/D case to remove forward
clutch piston.
CAUTION:
Be careful when applying pressure, for overpressure will
cause plate section of piston return spring to deform.

AUTOMATIC TRANSMISSION (4 A/T) 7B1-53
DIRECT CLUTCH
DISASSEMBLY
1) Install direct clutch assembly (1) to center support (2) and
with 4 – 8 kg/cm
2 air pressure applied to second fluid hole
from the left, measure stroke of direct clutch piston as shown
in figure.
If it is not within standard range, use 3.55 mm, 3.75 mm or
4.0 mm (0.140 in., 0.147 in. or 0.157 in.) clutch backing plate
to adjust it to standard stroke.
Standard direct clutch piston stroke :
0.90 – 1.30 mm (0.035 – 0.051 in.)
2) Remove direct clutch assembly from center support and
then remove retaining ring.
3) Remove clutch backing plate (1) and then remove clutch
disc (3) and clutch plate (2).
4) Using special tool and hydraulic press (1), compress direct
clutch piston return spring (3) and remove retaining return
spring ring (2).
Special tool
(A) : 09926-98310
5) Remove direct clutch piston return spring.
CAUTION:
Be careful when applying pressure, for overpressure will
cause plate section of piston return spring to deform.

7B1-54 AUTOMATIC TRANSMISSION (4 A/T)
6) Install direct clutch cylinder to center support.
Remove direct clutch piston by blowing air into the second
hole from the left as shown in the figure. Also, remove direct
clutch inner piston by blowing air into hole at the extreme
right. And then remove O-rings from pistons.
Front upper valve body
ASSEMBLY
Assemble each component by reversing disassembly procedure
and noting the following points.
•Coil outer diameter and free length of each valve spring
should be as listed below. Be sure to use each one of correct
size.
Coil outer diameter and free length of each valve spring
•Install as many throttle valve compensating rings as written
down when disassembled.
•Tighten throttle cam bolt (1) to specified torque.
Tightening torque
Throttle cam bolt (a) : 7.5 N·m (0.75 kg-m, 5.5 lb-ft)
•Tighten pressure relief valve bolts (1) to specified torque.
Tightening torque
Pressure relief valve bolt (b) : 5.5 N·m (0.55 kg-m, 4.0 lb-ft)
Name of spring Outer diameter Free length
Secondary regulator
valve spring17.43 mm
(0.681 in.)71.27 mm
(2.806 in.)
Cut back valve spring 6.85 mm
(0.259 in.)23.0 mm
(0.906 in.)
Throttle valve
secondary spring8.56 mm
(0.337 in.)18.86 mm
(0.743 in.)
Throttle valve
primary spring10.90 mm
(0.429 in.)39.55 mm
(1.557 in.)

7B1-60 AUTOMATIC TRANSMISSION (4 A/T)
Accumulator piston and spring specification :
Tightening Torque Specification
Used forPiston outer
diameter “a”Spring free length “b”
Direct clutch accumulator (2)31.80 – 31.85 mm
(1.252 – 1.254 in.)Upper spring 43.56 mm (1.715 in.)
Lower spring 30.00 mm (1.181 in.)
Forward clutch accumulator (1)31.80 – 31.85 mm
(1.252 – 1.254 in.)Upper spring 57.18 mm (2.251 in.)
Lower spring 30.50 mm (1.201 in.)
Second brake accumulator (3)34.80 – 34.85 mm
(1.370 – 1.372 in.)Upper spring 56.16 mm (2.211 in.)
Lower spring 18.5 mm (0.728 in.)
Fastening partTightening torque
Nm kg-m lb-ft
Automatic transmission fluid drain plug 23 2.3 17.0
Transfer oil level/filler and drain plugs 23 2.3 17.0
Transmission case plug 17 1.7 12.5
Manual select lever nut 13 1.3 9.5
Manual select cable nut 7 0.7 5.5
Manual selector assembly bolts 18 1.8 13.5
Transmission to engine bolts and nuts 85 8.5 61.5
Engine rear mounting bolts
Engine rear mounting member bolts50 5.0 36.5
Universal joint flange bolts and nuts 50 5.0 36.5
Torque converter mounting bolts 65 6.5 47.0
Adapter case or extension case bolts 42 4.2 30.0
Transmission range switch lock bolt 5.5 0.55 4.0
Oil pipe union bolts 35 3.5 22.5
Drive plate bolts 78 7.8 56.5
Interlock cable clamp screw 2.2 0.22 1.5
Interlock cable outer mounting nut 13 1.3 9.5

CLUTCH 7C1-1
7C1
SECTION 7C1
CLUTCH
NOTE:
The clutch of this model is the same as that of H25 engine in the construction and operation.
Refer to the same section of the Service Manual mentioned in the FOREWORD of this manual for ser-
vice procedure.

7C1-2 CLUTCH

CRUISE CONTROL SYSTEM 8E-1
6F1
6F2
6G
6H
6K
7A
7A1
7B1
7C1
7D
7E
8E
8A
8B
8C
8D
8B
9
10
10A
10B
SECTION 8E
CRUISE CONTROL SYSTEM
CONTENTS
General Description ....................................... 8E-2
Cautions in Servicing ................................... 8E-2
Symbols and Marks ...................................... 8E-2
Abbreviations ............................................... 8E-2
Wiring Color Symbols ................................... 8E-2
Joint Connector ............................................ 8E-2
Fuse Box and Relay ..................................... 8E-2
Power Supply Diagram ................................ 8E-2
Cruise Control System ................................. 8E-3
Cruise control system circuit .................... 8E-3
Components and functions....................... 8E-4
Cancel Conditions .................................... 8E-5
Diagnosis ........................................................ 8E-5
Diagnosis Table ........................................... 8E-5
Note on System Circuit Inspection ............... 8E-7
Cruise Main Switch Indicator Lamp
Circuit Check ................................................ 8E-8
“Cruise” Indicator Lamp Circuit Check ......... 8E-9
Cruise Main Switch, Coast/Set,
Resume/Accel and Cancel Switches
Circuits Check ............................................ 8E-10
VSS Circuit Check ...................................... 8E-11
Stop Lamp Switch (with Pedal Position
Switch) Circuits Check ............................... 8E-12Transmission Range Switch Circuit Check 8E-13
Clutch Pedal Position Switch Circuit Check 8E-14
Throttle Valve Opening Signal Circuit
Check ......................................................... 8E-15
Overdrive and TCC off Command Signal
Circuit Check.............................................. 8E-16
Cruise Control Module Power and Ground
Circuits Check ............................................ 8E-16
Cruise Control Module and Its Circuit
Inspection................................................... 8E-17
Cruise Cable Play Inspection and
Adjustment ................................................. 8E-19
On-Vehicle Service ...................................... 8E-19
Cruise Main Switch .................................... 8E-19
Coast/Set, Resume/Accel and Cancel
Switches..................................................... 8E-20
Vehicle Speed Sensor (VSS) ..................... 8E-20
Transmission Range Switch ...................... 8E-20
Clutch Pedal Position (CPP) Switch .......... 8E-21
Stop Lamp Switch (with Pedal Position
Switch) ....................................................... 8E-22
Cruise Control Actuator Assembly
(with Control Module) ................................. 8E-23
Cruise Cable .............................................. 8E-24

WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:
Service on and around the air bag system components or wiring must be performed only by an
authorized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under
“General Description” in air bag system section in order to confirm whether you are performing ser-
vice on or near the air bag system components or wiring. Please observe all WARNINGS and “Ser-
vice Precautions” under “On-Vehicle Service” in air bag system section before performing service
on or around the air bag system components or wiring. Failure to follow WARNINGS could result in
unintentional activation of the system or could render the system inoperative. Either of these two
conditions may result in severe injury.
Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system
may be activated by reserve energy in the Sensing and Diagnostic Module (SDM).