2001 SUBARU LEGACY service

Maintenance and service11-33
–
CONTINUED –

Recommended clutch fluid
FMVSS No. 116, fresh DOT 3 or 4 brake fluid
Brake booster
If the b rake b ooster d oes not op erate as d esc rib ed b elow, have it
c hec ked b y your SUBARU d ealer.
1. With the eng ine off, d ep ress the b rake p ed al seve ral times, ap p lying
the same p ed al forc e eac h time. The d istanc e the p e d al travels should
not vary.
2. With the b rake p ed al d ep ressed , start the eng ine. The p ed al should
move slig htly d own to the floor.
3. With the b rake p ed al d ep ressed , stop the eng ine a nd keep the p ed al
d ep ressed for 30 sec ond s. The p ed al heig ht should n ot c hang e.
4. Start the eng ine ag ain and run for ab out one minu te then turn it off.
Dep ress the b rake p ed al several times to c hec k the b rake b ooster.
Brake b ooster op erates p rop erly if the p ed al stroke d ec reases with eac h
d ep ression.

Maintenance and service11-35
–
CONTINUED –
and measure the d istanc e b etween the up p er surfac e
of the p ed al
p ad and the floor.
When the measurement is smaller than the sp ec ific at ion, or when the
p ed al d oes not op erate smoothly, c ontac t with your SUBARU d ealer.
Clutch pedal (Manual transmission vehicles)
Chec k the c lutc h p ed al free p lay and reserve d istan c e ac c ord ing to the
maintenanc e sc hed ule in the “Warranty and Maintenanc e Booklet ”.
Checking the clutch function
Chec k the c lutc h eng ag ement and d iseng ag ement.
1. With the eng ine id ling , c hec k that there are no a b normal noises
when the c lutc h p ed al is d ep ressed , and that shifti ng into 1st or re-
verse feels smooth.
2. Start the vehic le b y releasing the p ed al slowly t o c hec k that the en-
g ine and transmission smoothly c oup le without any s ig n of slip p ag e.
Checking the clutch pedal free play
OM-H0224
0.16 —
0.51 in
(4.0 — 13.0 mm)
Lig htly p ress the c lutc h p ed al d own with your fing e r until you feel re-
sistanc e, and c hec k the free p lay.
If the free p lay is not within p rop er sp ec ific ation , c ontac t your
SUBARU d ealer.

Maintenance and service11-37
–
CONTINUED –
n
Parking brake lining
WARNING
A safe location and situation should be selected for break-in driv- ing.
CAUTION
Pulling the parking brake lever too forcefully may cause the rear
wheels to lock. To avoid this, be certain to pull the lever up slowly
and gently.
1. Drive the vehic le at a sp eed of ab out 22 mp h (35 km/h).
2. With the p arking b rake release b utton p ushed in, p ull the p arking
b rake lever SLOWLY and GENTLY. (Pulling with a forc e of ap p roxi-
mately 33 lb [ 147 N, 15 kg ] .)
3. Drive the vehic le for ab out 220 yard s (200 meters ) in this c ond ition.
4. Wait 5 to 10 minutes for the p arking b rake to c oo l d own. Rep eat
this p roc ed ure.
5. Chec k the p arking b rake stroke. If the p arking b r ake stroke is out
of the sp ec ified rang e, ad just it b y turning the ad justing nut loc ated
on the p arking b rake lever.
Parking b rake stroke: 7 — 8 notc hes / 44 lb (196 N, 20 kg )
Parking brake stroke
Chec k the p arking b rake stroke ac c ord ing to the mai ntenanc e sc hed ule
in the “Warranty and Maintenanc e Booklet ”. When the p arking b rake is
p rop erly ad justed , b raking p ower is fully ap p lied b y p ulling the lever up
seven to eig ht notc hes g ently b ut firmly (ab out 44 lb , 196 N, 20 kg ). If the
p arking b rake lever stroke is not within the sp ec if ied rang e, have the
b rake system c hec ked and ad justed at your SUBARU d e aler.

Maintenance and service11-39
–
CONTINUED –

Tire pressure
For the b est b alanc e b etween fuel ec onomy, tire lif e, rid e c omfort, and
hand ling , tire p ressure should b e maintained in ac c ord anc e with sp ec ifi-
c ations. Chec k the tire p ressure when the tires are c old . Cold means that
the vehic le has b een p arked for three hours or has b een d riven less than
1 mile (1.6 km).
HB0382
The rec ommend ed tire p ressure and sizes are p rovid e d on the tire p lac -
ard , whic h is loc ated und er the d oor latc h on the d river’s sid e.
Tire rotation
Tire wear will vary with eac h wheel. To inc rease th e life of tires and keep
wear uniform, it is b est to rotate them every 7,500 mile (12,500 km).
When rotating tires, rep lac e any unevenly worn or d amag ed tire. After
rotating the tires, ad just tire p ressure and b e sur e to c hec k wheel nut
tig htness.

Maintenance and service11-41
–
CONTINUED –

Installing the wheel cover
HGA013BA
Alig n the valve with the valve hole in the c over, t hen fit the c over on
the wheel b y tap p ing your hand evenly around the c i rc umferenc e of
the c over.
NOTE When any of the wheels is removed and replaced for tire rotation or to change a flat tire, always check the tightness of the wheel nutsafter driving approximately 600 miles (1,000 km). If any nut is loose,tighten it to the specified torque.
Aluminum wheels (If equipped)
Aluminum wheels c an b e sc ratc hed and d amag ed easily . Hand le them
c arefully to maintain their ap p earanc e, p erformanc e , and safety.
When any of the wheels is removed and rep lac ed for tire rotation or to
c hang e a flat, always c hec k the tig htness of the wh eel nuts after d riving
ap p roximatly 600 miles (1,000 km). If any nut is lo ose, tig hten it to the
sp ec ified torq ue. Never ap p ly oil to the thread ed p arts, wheel nuts, or tap ered surfac e
of the wheel. Never let the wheel rub ag ainst sharp p rotrusions o r c urb s.
Be sure to fit tire c hains on uniformly and c omp let ely around the tire,
otherwise the c hains may sc ratc h the wheel.

Maintenance and service11-43
–
CONTINUED –
Replacement of windshield wiper blades
Grease, wax, insec ts, or other materials on the win
d shield or the wip er
b lad e results in jerky wip er op eration and streakin g on the g lass. If you
c annot remove the streaks after op erating the wind s hield washer or if the
wip er op eration is jerky, c lean the outer surfac e o f the wind shield (or rear
wind ow) and the wip er b lad es using a sp ong e or soft c loth with a neutral
d eterg ent or mild -ab rasive c leaner. After c leaning , rinse the wind shield
and wip er b lad es with c lean water. The wind shield i s c lean if b ead s d o
not form when you rinse the wind shield with water.
CAUTION
Do not clean the wiper blades with gasoline or a solvent, such as
paint thinner or benzene. This will cause deterioration of thewiper blades.
If you c annot eliminate the streaking even after fo llowing this method ,
rep lac e the wip er b lad es using the following p roc ed ures:
1. Raise the wip er arm off the wind shield .
2. Remove the wip er b lad e assemb ly b y hold ing its p i vot area and p ush-
ing it in the d irec tion shown b y the arrow while d e p ressing the wip er
b lad e stop p er.
HS0190
Stopper
3. Grasp the loc ked end of the b lad e rub b er assemb ly and p ull it firmly
until the stop p ers on the rub b er are free of the me tal sup p ort.

Maintenance and service11-45
–
CONTINUED –
HS0194
HS0193
Stopper
6. Install the wip er b lad e assemb ly to the wip er arm . Make sure that it
loc ks in p lac e.
7. Lower the wip er arm. Battery
WARNING
Before beginning work on or near any battery, be sure to extin-
guish all cigarettes, matches, and lighters. Never expose a bat- tery to an open flame or electric sparks. Batteries give off a gaswhich is highly flammable and explosive. For safety, in case an explosion does occur, wear eye protec-
tion or shield your eyes when working near any battery. Never
lean over a battery. Do not let battery fluid contact eyes, skin, fabrics, or paint be-
cause battery fluid is a corrosive acid. If battery fluid gets on yourskin or in your eyes, immediately flush the area with water thor-
oughly. Seek medical help immediately if acid has entered theeyes.If battery fluid is accidentally swallowed, immediately drink a
large amount of milk or water, and seek medical attention
immediately. To lessen the risk of sparks, remove rings, metal watchbands,

Maintenance and service11-47
–
CONTINUED –
two fuse b oxes. The one is loc ated und er the instru
ment p anel b ehind
the c oin tray on the d river ’s seat sid e. The other one is housed in the
eng ine c omp artment. The fuse p uller and sp are fuses are stored in the
main fuse b ox c over in the eng ine c omp artment.
If any lig hts, ac c essories or other elec tric al c ont rols d o not op erate, in-
sp ec t the c orresp ond ing fuse. If a fuse has b lown, rep lac e it.
HS0208
HS0204
Good
BlownFuse puller
Spare fuses
1. Turn the ig nition switc h to the “LOCK ” p osition and turn off all elec tri-
c al ac c essories.
2. Remove the c over.
(For b ehind the c oin tray: op en the c oin tray and p ull it horizontally to
remove it.)
3. Determine whic h fuse may b e b lown. The b ac k sid e of eac h fuse b ox
c over and the “Fuse and c irc uits ” sec tion in c hap ter 12 in this manual
show the c irc uit for eac h fuse.
HS0207
Fuse puller