Page 244 of 357

8-202. Move the end sup p ort and inner c lamp to unhook un
d er the b ot-
tom of the roof rail on b oth sid es.
3. Carefully raise the c rossb ar from roof rails. NOTE It may be necessary to move the Front crossbar rearward, near the center of the roof rail for easier removal. Use care not tocross-thread the screw in the insert if it has been removed. n To install the crossbar
Front crossbar:
Front c rossb ar has the Load Lab el on left-hand sid e .
HS1006BB
1. Before p lac ing the c rossb ar on the roof rails, ma ke sure that the
T-30 torx head sc rew is fully loosened from eac h end sup p ort .
2. Slid e the inner c lamp on the end sup p ort outward as far as p os-
sib le.
3. With the front d irec tion arrow lab el on the top r ig ht sid e of the
c rossb ar p ointing toward the front of the vehic le, c arefully p lac e the
c rossb ar ac ross the top of the vehic le so that the c rossb ar end sup -
p orts rest on the top of the roof rails ap p roximate ly 6 inc hes (150 mm)
rearward in the front rad ius of the roof rail.
4. Move the end sup p ort and inner c lamp to hook und e r the b ottom
of the roof rail on b oth sid es and loosely assemb le the T-30 torx
head sc rew with the tool p rovid ed into the thread ed insert in the inner
c lamp on eac h end of the c rossb ar.
Page 245 of 357
Starting and operating8-21
–
CONTINUED –
NOTE It may be necessary to start the inner clamp and end support at the center of the roof rail for easier installation, then move the
crossbar forward. Use care not to cross-thread the screw in theinsert if it has been removed.
5. Ad just the alig nment of the c rossb ar on the roof
rails and tig hten to
30 to 35 inc h lb s. (3.4 to 4.0 N-m, 0.35 to 0.41 kg -m) with the torx
tool p rovid ed . If availab le, you may use a T-30 tor x b it and torq ue
wrenc h to tig hten the c rossb ar torx head sc rew.
Rear crossbar:
HS1007BB
Install the rear c rossb ar in the same manner as the front c rossb ar.
NOTE The rear crossbar should be positioned 6 inches (150 mm) for- ward of the rear radius in the roof rail.
NOTE
Before each use of the roof crossbar, make sure the four T-30 cross- bar clamp screws have been checked, and re-tightened, if neces-
sary, to 35 in. lbs. (4.0 N-m, 0.41 kg-m), as outlined in Step #5 above.
Page 258 of 357

9
In case of emergency Hazard warning flasher9-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flat tires 9-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jump starting 9-8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine overheating 9-10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Towing 9-11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Moonroof – if the moonroof cannot be closed 9-15 . . . . . . . . . . . . . . . . . .
Maintenance tools 9-16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire changing tools 9-16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 272 of 357
In case of emergency9-15
–
CONTINUED –
Moonroof –
if the moonroof cannot be closed
If the moonroof c annot b e c losed with the moonroof switc h, you c an
c lose the sunroof manually.
1. Take out the hex-head ed wrenc h from the g love c om p artment and
sc rewd river from the tool b ag .
HS0360
2. Remove the p lug on the roof trim loc ated to the r ear of the moonroof
b y inserting the end of the reg ular sc red river b etw een the roof and p lug
and p rying it off.
HS0361
3. Insert the wrenc h in the end of the motor shaft.
To c lose the moonroof, turn the wrenc h c ounterc loc k wise.
Have your vehic le c hec ked and rep aired b y an author ized SUBARU
d ealer.
Page 273 of 357