2001 Peugeot Partner VU tow

3
2
1
0
4
5
6
Front wipers 0Stop
1 Intermittent wipe
2 Normal wipe
3 Rapid wipe
4 Single stroke wipe
Press downwards Front windscreen washPull the stalk towards you. This starts a timed wiping operation. Note : - Position 1: the intermittent wipe
will automatically adjust according to the vehicle speed.
- Positions 1, 2 and 3: when statio-
nary, the wipe speed will automati-cally reduce.
- The engaging of reverse gear, when the front wiper is operating,makes the rear wiper operate. 5 Rear screen wiper For intermittent wipe: twist the ring forwards. 6 Rear screen wash
For screen wash and wipe: turn the ring for-wards.
On release: approximately fourwipes, then it stops. Electric demister* : Electric demister for rear screen or rear view mirrors or both simulta-
neously, according to specifica-
tion. The light indicating operation
switches off automatically afterapproximately 12 minutes to pre-vent excessive power consump-tion. Press once to stop thedemisting function. Press onceagain to restart for 12 minutes. The electric demister will only ope- rate when the engine is running.
* According to specification or country.
39I-17VISIBILITY

C
Interior mirror Anti-dazzle position. Pivot the lever towards you. Reading of cards * The athermal windscreen featuresa special zone Clocated above
the rear view mirror allowing theelectronic reading of access per-mits (for example : motorwaycards). Exterior mirrors Manually controlled The mirrors can be adjusted in allfour directions from inside. Folding down when parked The exterior mirrors can be folded
down manually from outside. Thisoperation does not in any way
affect the initial adjustment.Electrically controlled Passenger side mirror This mirror can be adjusted in all four directions from the driver'sseat by operating the directionalknob. Demisting of the mirrors is con- trolled by the rear screen demisterbutton, located in the centre of thefascia.
23I-12MIRRORS
* According to model

A
B
Repriming the circuit
To reprime after running out of diesel : - Fill the tank with at least five litres of diesel, with the vehicle parked on as level a surface as possible. - Operate the manual repriming pump until resistance is felt.
- Operate the starter, pressing the accelerator lightly until the engine starts. If the engine fails to start at the first attempt, wait for 15 seconds and then try again. If it fails to start after several attempts, repeat the operation from the beginning. With the engine at idle, press the accelerator lightly to bleed the system.
86V- 3DIESEL INJECTION SYSTEM
1.9 Diesel engine, removal of the engine undertray- Pull the securing clip Atowards the front
of the vehicle.
- Remove the dipstick.
- Unscrew bolt Band remove it.
- Remove the undertray.
- Reprime the circuit.
- Refit the undertray (engine not running).

ABS system*
This system increases safety by preventing the wheels from locking in the event of harsh braking or in conditions of poor grip. It enables the driver to maintain control of the steering.
The operating capacity of all the essential electrical elements of the ABS system is controlled by an electronic moni-
toring system both before and during driving. The ABS light comes on when the ignition is switched on, and should
go out after approximately two seconds. If the light does not go out, this indicates that the ABS is disconnected due
to a fault. Likewise, if the light comes on while driving, this indicates that the ABS is not operating. In both cases,
the normal braking system remains effective, as on a vehicle without ABS. However, to avoid the occurrence of other
faults with unknown consequences, the ABS should be inspected as soon as possible by an approved dealer.
It is still necessary to drive carefully on slippery surfaces (loose stones, snow, ice, etc.)..
67III-3BRAKES
Handbrake
The handbrake is operated by pulling the lever upwards. The greater the slope you are on, the greater the force that should be applied in pulling the
lever.
To ease the action of the handbrake lever, it is recommended that you press the brake pedal at the same time. As a precaution, 1st gear should be engaged in all cases. On steep slopes, you should also turn the wheels towards the kerb.
To release the handbrake, pressthe button while pulling the lever up, then
lower the lever to the fully down position.The warning light comes on if the handbrake is on or not fully released, with the ignition on.
* According to model or country.

Ashtray
To empty, press the locking tongue and slide the ashtray unit towardsyou. Push it back into position. Lighter Push in and wait a few moments for the lighter to release automati-
cally.
WARNING :keep children away
from the cigar lighter as it can ope- rate even with the ignition swit-
ched off (see fuse F23 - F23B). Storage compartments andbottle holder (for 1.5 litre bottle + 1 cup or 33 cl bottle).
Sun visor
To avoid sun glare through the windscreen, fold the sun visordownwards. In case of side glare,through the door windows, releasethe sun visor from its inside faste-ning and pivot it to the side.
74IV-3COMFORT

97
Front direction indicators and side lamps Open the bonnet, press the tab and push the lamp unit outwards. Turn the bulb base one quarterturn and change the bulb. Replace the lamp unit, engaging the two upper and lower guides.Push the lamp unit into position.Direction indicator siderepeaters Push the unit forwards to unclip it and pull it towards you.
Turn the bulb holder one quarterturn.
VI-4CHANGING BULBS

1
2
3
4
A
98
Rear lamps Note the position of the faulty bulb. Bulbs : 1 Fog lamp
2 Direction indicator lamp
3 Reversing lamp
4 Brake lamp - Side lamp Open the rear door to 180¡ on the side of the faulty bulb (see ÒOPEN-
ING THE DOORSÓ). Unscrew the butterfly nut
A.
Gently push the lamp unit towards the inside of the vehicle to releasethe two side retaining lugs. Remove and disconnect the lamp unit. Unclip the bulb holder as indicatedby the arrows. Change the faultybulb.When refitting, ensure that thegrommet is properly seated andclose the rear doors in the correct
sequence (see ÒOPENING THEDOORSÓ).VI-4CHANGING BULBS

100
Number plate lamp Unscrew the translucent cover to gain access to the bulb. Additional brake lamp* (Third brake lamp) Remove the cover by pressing on the tab (round section) at the endof the lamp (in the direction of thearrows).
Pull the cover towards the rear.Remove the bulb holder by squee- zing the two tabs. Pull out the faulty bulb and change it.
To refit, proceed in the reverse
order. * Option depending on version.VI-4CHANGING BULBS