2001 PEUGEOT 106 Brake

PRACTICAL INFORMATION7676
16-valves 1587 cm3
engine
4
1
3
6
87 2
5
1
.Air Þlter
2 .Brake ßuid
3 .Battery
4 .Power steering
5 .Dipstick
6 .Engine oil Þller
7 .Coolant
8 .Reservoir for front/rear screen and headlamp wash-wipe*
06-05-2002

PRACTICAL INFORMATION7777
1527 cm3
diesel engine
4
1
3
5
6
87 2
1
.Air Þlter
2 .Brake ßuid
3 .Battery
4 .Power steering
5 .Dipstick
6 .Engine oil Þller
7 .Coolant
8 .Reservoir for front/rear screen and headlamp wash-wipe*
06-05-2002

CHECKING THE LEVELS 1. Air filter
The air filter element must be changed at the recommendedintervals. If you drive in a dustyatmosphere, change it twice asoften. Follow the recommendations given in the maintenance schedule. 2. Brake fluid
The level must always be above the
DANGER mark on the reservoir. Inthe event of a signiÞcant drop in theßuid level, consult a PEUGEOT
dealer immediately. Use fluids
approved by the manufacturer,which conform to DOT 3 or DOT 4standards. 3. Battery
At the beginning of winter, have the battery checked by a PEUGEOT
dealer. In summer (30¡C and above) or if the battery is in heavy use, checkthe level of electrolyte; it must coverthe separator plates at all times. If
necessary, top up with distilled
water. 4. Power steering* When the engine is cold, the level must always be above the MINmark, close to the MAX mark. 5. Dipstick Check the oil level on ßat ground, with the engine cold and preferably
before the Þrst journey of the day. Never exceed the maximum level.
Check the level regularly.
6. T
opping up with oil
Y our oil must be changed in accor-
dance with the maintenance sche- dule. The oil must be topped up between oil changes. Regularly check and top-up the oil level. Maximum oil consumption is 0.5 litres per 600 miles (1000 km). 7. Coolant Engine cold: the coolant level must be between the min and max marksin the expansion chamber with the
cap removed. To close, turn the capto the second notch*. Cooling circuit Always use the coolant which is approved by the manufacturer
(PROCOR TM108 / GLYSANTING33 or REVKOGEL 2000). If this isnot possible, top up with distilledwater and have the protection level
checked by a PEUGEOT dealer. When the engine is hot, the coolant temperature is regulated by the fan.As the fan can operate with theignition key removed, and as thecooling circuit is pressurised,
do
not carry out any work for atleast an hour after switching offthe engine .
Note: the coolant does not need tobe renewed.
8. Front/rear screen and headlamp wash reservoir*
For optimum cleaning quality and
for your safety, it is best to use cleaning products approved byPEUGEOT (capacity 4.5 litreswithout headlamp wash, 5.5 litreswith headlamp wash). * According to speciÞcation
PRACTICAL INFORMATION7878
06-05-2002

PRACTICAL INFORMATION79
Visual brake pad wear indicator*
The front brakes are Þtted with visual wear indicators. Regularly check the thickness of the brake pads.
To check: turn the wheels to full lock on the side to be checked. The thickness of pad remaining is represented by the measu-
rement X. When the measurement is zero, the brake pads must be changed. Advice As brake pad wear depends on the way in which the vehicle is driven, particularly if the vehicle is used for urban driving or f or
short journeys, or is driven in a very sporty manner, it may be necessary to check the thickness of the pads even between ser- vice intervals. * According to speciÞcation
79
06-05-2002

Special procedure for Sport model Positioning the jack ÐClose the jack completely.
Ð Position the jack under the vehicle at the jacking points tilting it by 90¡, so that the jack handle hinge is at the same height as the sill trim, then straighten it.
Ð Check that the jack is in correct contact with the sill.
Replacing the wheel in the carrier Ð Position the jack storage box with the arrow pointing forwards.
PRACTICAL INFORMATION8181
For your safety, always change a wheel:
Ð on level, solid, non-slipperyground,
Ð with the handbrake applied,
Ð
with Þrst or reverse gear engaged,
Ð Chock the vehicle.
Ð Never position yourself undera vehicle which is supportedonly by a jack. Use a ramp.
After changing the wheel Ð Have the wheel bolts and the tyre pressure checked assoon as possible.
Ð Have the damaged tyrerepaired so that it can bereturned to the vehicle assoon as possible.
Ð The Òspace-savingÓ* type ofspare wheel is Þtted with a115/70R 15 tyre and is for
temporary use only. - Pressure: 61 lbf. in 2
(4.2 bars).
- Maximum speed: 50 m.p.h. (80 km/h).
* According to speciÞcation
3
Never place the jack in contact with the sill trim.
06-05-2002

PRACTICAL INFORMATION
Direction indicator bulbs PY21W Access to the bulbs is from inside the wheel arch. Turn the wheels to full lock (to the
left to change the right hand bulb and vice versa). Open the access ßap.T urn the socket 1/4 turn.
Change the bulb. Ensure that the flap is closed
correctly. Side repeater W5W* Pull the rear part of the transparent
cover and detach the assembly. Support the connector and turn the transparent cover 1/4 turn. Change the bulb.
Rear lights Direction indicators
PY21W
Reversing lights P21W
Fog lamp P21W
T ail lights P5W
Brake/tail lights P21/5W
From inside the luggage com- partment: Remove the plastic protector 1.
Remove the air outlet grille 2using
a cross-head screwdriver. Slacken the two wing nuts 3and
release the light block 4.
Pinch the lugs 5to remove the
bulb-holder. Change the bulbs. * According to speciÞcation
84
4
3
1
2
5
06-05-2002

PRACTICAL INFORMATION
Additional brake light 5 W5W bulbs Access to the light is easier if the luggage compartment is open. Remove the plastic protector by pressing the side tabs. Pinch the lugs to release the bulb-
holder. Change the bulbs.Front fog lamps/long range lights H1/55W* Access to the bulbs is from under- neath the vehicle. T
urn the socket a 1/4 turn.
Change the bulb. * According to speciÞcation
85
06-05-2002

PRACTICAL INFORMATION
Direction indicator bulbs PY21W Access to the bulbs is from inside the wheel arch. Turn the wheels to full lock (to the
left to change the right hand bulb and vice versa). Open the access ßap.T urn the socket 1/4 turn.
Change the bulb. Ensure that the flap is closed
correctly. Side repeater W5W* Pull the rear part of the transparent
cover and detach the assembly. Support the connector and turn the transparent cover 1/4 turn. Change the bulb.
Rear lights Direction indicators
PY21W
Reversing lights P21W
Fog lamp P21W
T ail lights P5W
Brake/tail lights P21/5W
From inside the luggage com- partment: Remove the plastic protector 1.
Remove the air outlet grille 2using
a cross-head screwdriver. Slacken the two wing nuts 3and
release the light block 4.
Pinch the lugs 5to remove the
bulb-holder. Change the bulbs. * According to speciÞcation
84
4
3
1
2
5
06-05-2002