2001 MAZDA MODEL 626 maintenance

Form No. 8P95-EA-00G
Maintenance
8-15
Engine oil-filler cap
Engine oil dipstick
Air filter
Automatic transaxle fluid-level dipstick
(only for automatic transaxle)
Brake/Clutch fluid reservoir
Fuse block
Battery
Coolant reservoir
Windshield washer fluid reservoir
J94A7002A2.5-liter engine
Power steering fluid reservoir
Cooling system cap

Form No. 8P95-EA-00G
J94A7003
(J18T7003)
(ILSAC)
Maintenance8-16

083-5A2E
 Engine Oil
 Recommended oil
Oil container labels provide important
information.
The quality designation “SG”, “SH”,“
SJ ”, or “ILSAC” must be on the label.
Engine oil viscosity, or thickness, has
an effect on fuel economy and
cold-weather operation (starting and
oil flow). Low-viscosity engine oils
can provide improved fuel ec onomy
and cold-weather performance. But high-temperature weather
conditions require higher-viscosity
engine oils for satisfactory lubrication.
When choosing an oil, consider the
temperature range your vehicle will
operate in before the next oil change.
Then select the recommended
viscosity from this chart.
–20 0 20 40 60 80 100 120
–30
–20–10 0 10 20 30 40 50
°C
( ° F)
Oil
5W-30 10W-30
|| | ||| | |||| | | | | | |

Form No. 8P95-EA-00G
Maintenance
8-17
CAUTION
!
Using oils of viscosity besides
those recommended for specific
temperature ranges could result in
engine damage.Energy conserving oils are
recommended. A chief contribution
they make to fuel economy is reducing
the amount of fuel necessary to
overcome engine friction.

083-6A2E
J94A7005
2.0-liter engine
OKInspecting engine oil level
1. Be sure the vehicle is on a level surface.
2. Warm up the engine to normal operating temperature.
OK
J94A7004
2.5-liter engine3. Turn it off and wait 5 minutes forthe oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and reinsert it fully.

Form No. 8P95-EA-00G
Maintenance8-185. Pull it out again and examine thelevel. It’ s OK between L and F.
But if it’ s near at or below L, add
enough oil to bring the level to F.
CAUTION
!
Don’ t add engine oil over F.
This may cause engine damage.NOTEThe distance between L and F on
the dipstick represents 1.0 L (1.06
US qt, 0.88 Imp qt).

083-7CE
Changing engine oil and filter
Change engine oil and filter according
to Scheduled Maintenance (page
8-3).
Please act responsibly—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
WARNING
!
Handling Used Engine Oil:Continuous contact with used
engine oil could be dangerous. It
could cause skin cancer. Always
wash with soap and water
immediately after changing oil
and filter.

Form No. 8P95-EA-00G
J94A7007 (J18T7009)
Loosen
Drain plug Oil-filler cap
Tighten
2.5-liter engine
Maintenance
8-19
J94A7006
(J18T7008)
Loosen
2.0-liter engine
Oil-filler capTighten
Drain plug
Changing engine oil
1. Warm up the engine for a few minutes and turn it off. Remove the
oil-filler cap. 2. Remove the drain plug and drain
the oil into a suitable container.
WARNING
!
Checking or Changing EngineOil:Hot engine oil could be
dangerous. If the engine has been
running, the engine oil becomes
very hot. You could be seriously
burned. Don’ t check or change
the engine oil when the engine is
hot.

Form No. 8P95-EA-00G
Maintenance8-20
083-47B1E
3. Replace the plug tightly after theoil has thoroughly drained.
4. Fill the engine with new oil to the F mark on the dipstick.
5. Securely replace the oil-filler cap.
6. Start the engine and inspect around the drain plug for leaks.
7. Turn it off and wait 5 minutes for the oil to return to the oil pan.

 083-48BE
Check the oil level and fill to the F
mark if necessary.
Oil capacity
(General reference only)
2.0-liter engine:
3.3 L (3.5 US qt, 2.9 Imp qt)
2.5-liter engine: 3.7 L (3.9 US qt, 3.3 Imp qt)
NOTE• The indicated engine oil
capacities are for general
reference purposes only. When
adding or changing oil, verify
the engine oil level with the oil
dipstick.
• Use only specified engine oil
(page 8-16).Changing oil filter
Because you need a special tool to
retighten the filter, an Authorized
Mazda Dealer should do the work.

Form No. 8P95-EA-00G
Maintenance
8-21
083-8C2E
 Engine Coolant
 Inspecting coolant level
WARNING
!
Hot Engine:A hot engine is dangerous. If the
engine has been running, parts of
the engine compartment can
become very hot. You could be
burned. Don’ t inspect the coolant
system or add coolant when the
engine is hot.
Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year—at the beginning of
the winter season—and before
traveling where temperatures may
drop below freezing.
Inspect the condition and connections
of all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.
The coolant should be at full in the
radiator and between the F and L
marks on the coolant reservoir when
the engine is cool.
083-9C1E
2.5-liter engine
J94A7042_a
2.0-liter engine
If it ’s at or near L, add enough coolant
to the coolant reservoir to provide
freezing and corrosion protection and
to bring the level to F.

Form No. 8P95-EA-00G
Maintenance8-22

083-10AE
Do not overfill.
If new coolant is required frequently,
consult an Authorized Mazda Dealer.
CAUTION
!
Radiator coolant will damage
paint. Rinse it off quickly.NOTEMixing green coolant with orange
coolant could decrease the service
life expentancy of the coolant. Use
only genuine Mazda orange
colored or equivalent coolant.


083-11DE
Changing coolant
Change coolant according to
Scheduled Maintenance (page 8-3).
CAUTION
!
• Use only soft (demineralized)
water in the coolant mixture.
Water that contains minerals
will cut down on the coolant’ s
effectiveness.
• Don’ t add only water. Always
add a proper coolant mixture.
CAUTION
!
• The engine has aluminum parts
and must be protected by an
ethylene-glycol-based coolant
to prevent corrosion and
freezing.
• DO NOT USE alcohol or
methanol antifreeze. DO NOT
MIX alcohol or methanol with
the coolant. This could damage
the cooling system.
• Don’ t use a solution that
contains more than 60 percent
antifreeze.
This would reduce
effectiveness.