2001 MAZDA MODEL 626 lock

Form No. 8P95-EA-00G
In Case of Emergency6-22
076-8B2E
3. Turn on the hazard warning flasher.
4. Have everyone get out of thevehicle and away from the vehicle
and traffic.
5. Remove the jack, lug wrench, and spare tire.
6. Block the wheel diagonally opposite the flat tire. When
blocking a front wheel, place the
block in front of the tire. When
blocking a rear wheel, place the
block behind the tire.
Q076-9H1E
J94S60047. Pry off the wheel cover or centercap with the beveled end of the lug
wrench.
NOTEForce the end of the wrench firmly
between wheel and cover or cap,
or removal will be difficult.

Form No. 8P95-EA-00G
In Case of Emergency
6-23
Q076-23CE
CAUTION
!
(Center Cap)
There is a valve-stem mark inside
the center cap. When installing the
center cap, align this mark with the
tire’s valve stem.
(Wheel Cover)
Align the notch on the wheel cover
with the valve stem when
installing it.
Damage could occur during
installation if the center cap or
wheel cover is not properly
aligned.
076-10A1E
J94A5018Lug wrench
8. Loosen the lug nuts by turning them counterclockwise one turn
each, but don’ t remove any until
the tire has been raised off the
ground.
076-11EE
Jacking position
J94A50199. Place the jack under the jacking position closest to the tire being
changed.

Form No. 8P95-EA-00G
In Case of Emergency
6-25

076-13D1E
J94A502010. Insert the lug wrench into the jack
and turn it clockwise until the tire
just clears the ground, less than
25 mm (1 in). Before removing
the lug nuts, make sure your
Mazda is firmly in position and
that it cannot slip or move. 11. Remove the lug nuts by turning
them counterclockwise; then
remove the wheel.
12. Mount the spare tire.
13. Install the lug nuts with the beveled edge inward; tighten
them by hand.
J94A5021
(J18Y5036)
14. Turn the lug wrench
counterclockwise and lower the
vehicle. Use the lug wrench to
tighten the nuts in the order
shown.

Form No. 8P95-EA-00G
I: Inspect and repair, clean, adjust, or replace if necessary
L : Lubricate
Maintenance8-6Schedule 1 (Cont ’d)
MAINTENANCE
INTERVALS
Number of months or miles (kilometers), whichever comes first
INTERVALS
Months
6
12
18
24
30
36
42
48
MAINTENANCE

1000 km
12
24
36
48
60
72
84
96
MAINTENANCE

ITEM
(
1000 miles)
(7.5)
(15)
(22.5)
(30)
(37.5)
(45)
(52.5)
(60)
Drum brakes
I
I
Disc brakes
I
I
Steering operation and linkages
I
I
Front suspension ball joints
I
I
Driveshaft dust boots
I
I
Bolts and nuts on chassis and body
I
I
Exhaust system heat shields
I
I
All locks and hinges
L
L
L
L
L
L
L
L
Air-conditioner refrigerant (if installed)
I
I
I
I
Air-conditioner compressor (if installed)
I
I
I
I

Form No. 8P95-EA-00G
I: Inspect and repair, clean, adjust, or replace if necessary
L : Lubricate
Maintenance
8-9
Schedule 2 (Cont ’d)
MAINTENANCE
INTERVALS
Number of months or miles (kilometers), whichever comes first
INTERVALS
Months
4
8
12
16
20
24
28
32
36
40
44
48
MAINTENANCE

1000 km
8
16
24
32
40
48
56
64
72
80
88
96
MAINTENANCE

ITEM
(
1000 miles)
(5)
(10)
(15)
(20)
(25)
(30)
(35)
(40)
(45)
(50)
(55)
(60)
Brake and clutch fluid level
I
I
I
I
I
I
I
I
I
I
I
I
Drum brakes
I
I
Disc brakes
I
I
I
I
Tire inflation pressure and tire wear
I
I
I
I
I
I
I
I
I
I
I
I
Steering operation and linkages
I
I
Power steering fluid level
I
I
I
I
I
I
I
I
I
I
I
I
Front suspension ball joints
I
I
Driveshaft dust boots
I
I
Bolts and nuts on chassis and body
I
I
I
I
Exhaust system heat shields
I
I
All locks and hinges
L
L
L
L
L
L
L
L
L
L
L
L

Form No. 8P95-EA-00G
Maintenance8-14
083-4AE
 Engine Compartment Overview
Cooling system cap
2.0-liter engine
Engine oil dipstick Air filter
Automatic transaxle fluid-level dipstick
(only for automatic transaxle)
Brake/Clutch fluid reservoir
Fuse block
Battery
Coolant reservoir
Windshield washer fluid reservoir
Power steering fluid reservoir
Engine oil-filler cap
J94A7001A

Form No. 8P95-EA-00G
Maintenance
8-15
Engine oil-filler cap
Engine oil dipstick
Air filter
Automatic transaxle fluid-level dipstick
(only for automatic transaxle)
Brake/Clutch fluid reservoir
Fuse block
Battery
Coolant reservoir
Windshield washer fluid reservoir
J94A7002A2.5-liter engine
Power steering fluid reservoir
Cooling system cap

Form No. 8P95-EA-00G
Maintenance
8-23
For mixture percentage:
Volume
Protection
Antifreezesolution
Water
Above –16° C (3°F)
35%
65%
Above –26° C (–15°F)
45%
55%
Above –40° C (–40°F)
55%
45%
WARNING
!
Removing the Cooling SystemCap:Removing the cooling system cap
or drain plug while the engine is
running or hot is dangerous. This
might lead to cooling system and
(Continued)
engine damage and could result
in serious injury from escaping
hot coolant or steam. Turn off the
engine and wait until it’ s cool.
Even then, be very careful when
removing the cap or drain plug.
Wrap a thick cloth around it and
slowly turn it counterclockwise to
the first stop. Step back while the
pressure escapes. When you’re
sure all the pressure is gone, press
down on the cap — still using a
cloth — turn the cap, and remove
it.

083-12D1E
Cooling system cap
J94A7009A2.0-liter engine
Loosen
Tighten
LoosenTighten
Drain plug
To change coolant
1. Remove the cooling system cap.
2. Only when the engine is cool,
loosen the radiator drain plug and
drain the coolant into a suitable
container.