2001 Lexus ES300 light

INTERIOR EQUIPMENT
78
Vehicles without moon roof
To turn on the personal light, push the switch. To
turn it off, push the switch again.

INTERIOR EQUIPMENT
79
14E052
Vehicles with moon roof
To turn on the personal light, push the switch. To
turn it off, push the switch again.
IGNITION SWITCH LIGHT
14E054

INTERIOR EQUIPMENT
80For easy access to the ignition switch, the ignition
switch light comes on when any of the doors are
opened.
The light remains on for about 15 seconds and goes out
after all the doors are closed. However, the light goes
out immediately when all the doors are locked or the
ignition key is in the ªACCº or ªONº position.

INTERIOR EQUIPMENT
81
CLOCK
14E006a
The digital clock indicates the time with the ignition
key at the ªACCº or ªONº position. To reset the
hour, press the ªHº button. To reset the minutes,
press the ªMº button. To adjust the time to the
nearest hour, press the ª:00º button.
For example, if the ª:00º button is pressed when the time
is between 9:30 ± 9:59 or between 10:01 ± 10:29, the
time will change to 10:00.
With the tail lights on, the brightness of the time
indication will be reduced.
If the electrical power source has been disconnected
from the clock, the time display will automatically be set
to 1:00 (one o'clock).CIGARETTE LIGHTER ANDASHTRAY

INTERIOR EQUIPMENT
82
14E060
Front cigarette lighter and ashtray
To use the cigarette lighter and ashtray, first push
against the ashtray cover. Then when the ashtray
opens out, press in the cigarette lighter. When it
becomes heated, it automatically pops out ready for
use.
Do not hold the cigarette lighter pressed in.
If the engine is not running, the ignition key must be in
the ªACCº position.
When finished with your cigarette, thoroughly extinguish
it in the ashtray to prevent other cigarette butts from
catching fire. After using the ashtray, push it back in
completely.
To remove the ashtray, just pull it up.
Use a Lexus genuine cigarette lighter or equivalent for
replacement.

INTERIOR EQUIPMENT
86
14E061
 1Unlock 2Open 3Lock
To open the glove box door, pull the lever. To lock
the glove box door, insert the master key and turn it
clockwise.
With the tail lights on, the glove box light will come on
when the glove box door is open.
The trunk lid opener main switch is installed inside the
glove box. See page 106 for further information.
For the CD automatic changer, see page 256.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, always keep the glove box door closed
while driving.

INTERIOR EQUIPMENT
88
GARAGE DOOR OPENER
The garage door opener (HomeLinkUniversal
Transceiver) is manufactured under license from
HomeLink
 and can be programmed to operate
garage doors, gates, entry doors, door locks, home
lighting systems, and security systems, etc.
(a) Programming the HomeLink
14E065
 1Indicator light 2 Buttons
The HomeLink in your vehicle has 3 buttons and
you can store one program for each button.
To ensure correct programming into the HomeLink
,
install a new battery in the hand±held transmitter prior to
programming.

INTERIOR EQUIPMENT
89
The battery side of the hand±held transmitter must be
pointed away from the HomeLink
 during the
programming process.
For Canadian users, follow the procedure in
ªProgramming an entrance gate/Programming all
devices in the Canadian marketº.
1. Decide which of 3 HomeLink
 buttons you want to
program.
2. Place your hand±held garage transmitter 25 to 75
mm (1 to 3 in.) away from the surface of the HomeLink
.
Keep the indicator light on the HomeLink
 in view while
programming.
3. Simultaneously press and hold the hand±held garage
transmitter button along with the selected HomeLink

button.
4. When the indicator light on the HomeLink
 changes
from a slow to a rapid flash after 20 seconds, you can
release both buttons.
5. Test the operation of the HomeLink
 by pressing the
newly programmed button. If programming a garage
door opener, check to see if the garage door opens and
closes. If the garage door does not operate, identify if your
garage transmitter is of the ªRolling Codeº type. Press
and hold the programmed HomeLink
 button. The
garage door has the rolling code feature if the indicator
light (on the HomeLink
) flashes rapidly and then
remains lit after 2 seconds. If your garage transmitter is
the ªRolling Codeº type, proceed to the heading
ªProgramming a rolling code systemº.
6. Repeat steps 2 through 5 for each remaining
HomeLink
 button to program another device.
Programming a rolling code system
If your device is ªRolling Codeº equipped, it is
necessary to follow steps 1 through 4 under the
heading ªProgramming the HomeLink
º before
proceeding with the steps listed below.
1. Locate the ªtrainingº button on the ceiling mounted
garage door opener motor. The exact location and color
of the button may vary by brand of garage door opener.
Refer to the owner's guide supplied by the garage door
opener manufacturer for the location of this ªtrainingº
button.
2. Press the ªtrainingº button on the ceiling mounted
garage door opener motor.
Following this step, you have 30 seconds in which to
initiate step 3 below.