2001 LAND ROVER FREELANDER ECU

ENGINE - K SERIES KV6
REPAIRS 12-3-49
Torque converter drive plate
$% 12.53.13
Remove
1.Remove automatic gearbox.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Gearbox - KV6.
2.Assemble LRT-12-161 to LRT-12-199 and
secure with clamp bolt.
3.Position LRT-12-161 and LRT-12-199 to
crankshaft pulley to restrain crankshaft.
4.Remove and discard 6 Patchlok bolts securing
drive plate to crankshaft.
5.Remove drive plate from crankshaft.Refit
1.Clean bolt holes in crankshaft using an old
drive plate bolt with two saw cuts at an angle of
45° to the bolt shank.
2.Clean drive plate and mating face of
crankshaft.
3.Position LRT-12-161 and LRT-12-199 to
crankshaft pulley to restrain crankshaft.
4.Position drive plate to crankshaft.
5.Fit new Patchlok bolts securing drive plate to
crankshaft and tighten in sequence shown to:
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - 100 Nm (74 lbf.ft)
6.Remove LRT-12-161 and LRT-12-199 from
crankshaft pulley.
7.Fit automatic gearbox.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Gearbox - KV6.

ENGINE - K SERIES KV6
REPAIRS 12-3-51
Gasket - oil pump
$% 12.60.25
Remove
1.Disconnect battery earth lead.
2.Drain engine oil.

+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.
3.Remove camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
4.Remove crankshaft gear.
5.Disconnect multiplug from oil pressure switch.
6.Loosen and remove oil cooler pipe unions from
oil filter housing, remove and discard 2 'O'
rings.
7.Using strap wrench, remove and discard oil
filter.8.Using sequence shown, remove and discard 16
bolts securing oil pump to cylinder block.
9.Remove oil pump.
10.Remove and discard oil pump gasket.
11.Remove and discard crankshaft front oil seal
from oil pump housing.

ENGINE - K SERIES KV6
REPAIRS 12-3-53
Sump - reseal
$% 12.60.38
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Drain engine oil.

+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.
4.Remove 3 bolts securing RH splash shield to
body and remove shield.
5.Remove 4 nuts securing engine oil cooler to
mounting bracket and position oil cooler aside.6.Remove bolt securing dipstick tube to cylinder
block.
7.Depress and hold down dipstick collar, remove
dipstick tube from sump.
8.Remove 3 bolts securing IRD support bracket
to sump.
9.Using sequence shown and noting their fitted
position, remove 10 bolts securing sump to
lower crankcase.
M12 6614
M12 7916
M12 6672

ENGINE - K SERIES KV6
12-3-54 REPAIRS
10.Using a mallet, gently tap sump sideways to
break sealant bond, remove sump.
CAUTION: Do not lever between sump and
lower crankcase.
Refit
1.Using a suitable cleaning solvent, clean sump
and mating face on lower crankcase. DO NOT
use a metal scraper on sealing surfaces.
2.Apply a 2 mm (0.1 in) bead of sealant, Part No.
STC 4600 along centre of sump flange, then
spread to an even film using a roller.
CAUTION: To avoid contamination,
assembly must be completed immediately
after application of sealant.
3.Position sump, fit bolts and tighten
progressively in the sequence shown to 35 Nm
(26 lbf.ft).
4.Fit bolts securing IRD support bracket to sump
and tighten to 88 Nm (65 lbf.ft).
5.Position engine oil cooler to mounting bracket,
fit and tighten nuts to 25 Nm (18 lbf.ft).
6.Position dipstick tube to sump and cylinder
block, fit bolt and tighten to 9 Nm (7 lbf.ft).
7.Fit splash shield and secure with bolts.
8.Fill engine with correct quantity and grade of oil.

+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.
9.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
10.Connect battery earth lead.
Switch - oil pressure
$% 12.60.50
Remove
1.Disconnect battery earth lead.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Remove RH front road wheel.
4.Remove 3 bolts securing RH splash shield to
body and remove shield.
5.Place container below oil pressure switch to
collect spillage.
6.Disconnect multiplug from oil pressure switch.
7.Remove oil pressure switch and discard
sealing washer.
M12 6675
10
9
135
8
4
7
26
M12 6614

ENGINE - K SERIES KV6
REPAIRS 12-3-55
Refit
1.Ensure oil pressure switch and mating face is
clean.
2.Fit oil pressure switch using a new sealing
washer and tighten to 14 Nm (10 lbf.ft).
3.Connect multiplug to oil pressure switch.
4.Remove oil container from underneath of
engine.
5.Fit splash shield and secure with bolts.
6.Fit RH road wheel and tighten nuts to 115 Nm
(85 lbf.ft).
7.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
8.Check engine oil level, top-up if necessary.
9.Connect battery earth lead.
Oil pressure relief valve
$% 12.60.56
Remove
1.Disconnect battery earth lead.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Remove RH front road wheel.
4.Remove 3 bolts securing RH splash shield to
body and remove shield.
5.Place suitable container under oil filter to collect
spillage.
6.Using strap wrench, remove and discard oil
filter.
M12 6614
M12 6660

ENGINE - K SERIES KV6
12-3-56 REPAIRS
7.Remove 4 nuts securing engine oil cooler to
mounting bracket and position oil cooler aside.
8.Remove oil pressure relief valve plug nut.
Note: If a hexagonal head plug and sealing
washer are fitted, discard sealing washer.
9.Remove spring and valve.Refit
1.Clean valve, spring and plug; remove all traces
of sealant from threads in oil pressure relief
valve bore and from threads of plug.
CAUTION: Do not use a tap.
2.Clean valve seating inside oil pump housing.
3.Check that valve slides freely in bore and that
valve and bore are free from scoring and
corrosion.
Note: Light corrosion may be removed using
grade 600 emery cloth soaked in oil.
4.Check free length of spring.

+ GENERAL DATA, Engine - KV6
Petrol.
5.Apply sealant, Part No. STC 50552 to plug
threads.
Note: If a hexagonal head plug and sealing
washer were fitted, fit new sealing washer to
plug.
6.Fit valve, spring and plug to oil pump housing.
Tighten plug to 25 Nm (18 lbf.ft).
7.Fill canister of replacement oil filter with clean
engine oil.
8.Lubricate new oil filter seal with clean engine oil
and fit filter.
9.Position engine oil cooler to mounting bracket,
fit and tighten nuts to 25 Nm (18 lbf.ft).
10.Remove oil container from underneath of
engine.
11.Fit splash shield and secure with bolts.
12.Fit RH road wheel and tighten nuts to 115 Nm
(85 lbf.ft).
13.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
14.Connect battery earth lead.
15.Check engine oil level, top-up if necessary.
M12 7916

ENGINE - K SERIES KV6
REPAIRS 12-3-57
Oil cooler - engine
$% 12.60.68
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
3.Remove RH front road wheel.
4.Remove 3 bolts securing RH splash shield to
body and remove shield.
5.Position container to collect spillage under oil
filter.
6.Loosen and remove oil cooler pipe unions from
oil filter housing, remove and discard 2 'O'
rings.
CAUTION: Failure to retain bosses will
result in damage to oil cooler. Always fit
plugs to open connections to prevent
contamination.
7.Position container to collect coolant spillage.8.Release clips and disconnect coolant hoses
from engine oil cooler.
CAUTION: Always fit plugs to open
connections to prevent contamination.
9.Remove 4 nuts securing engine oil cooler to
mounting bracket and remove oil cooler.
10.Restrain oil cooler pipe bosses on oil cooler
housing, loosen and remove oil cooler pipes
from oil cooler; remove and discard 2 'O' rings.
CAUTION: Always fit plugs to open
connections to prevent contamination.
Refit
1.Clean oil cooler pipe unions and mating faces.
2.Lubricate new 'O' rings with clean engine oil
and fit to oil cooler pipes.
3.Fit pipes to engine oil cooler, restrain bosses on
oil cooler body and tighten unions to 26 Nm (19
lbf.ft).
CAUTION: To prevent damage to
components, use two spanners when
loosening or tightening unions.
4.Position engine oil cooler to mounting bracket,
fit and tighten nuts to 25 Nm (18 lbf.ft).
5.Position oil cooler pipes to oil filter housing and
tighten unions to 26 Nm.
6.Connect coolant hoses to oil cooler and secure
with clips.
7.Fit splash shield and secure with bolts.
8.Fit RH road wheel and tighten nuts to 115 Nm
(85 lbf.ft).
9.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
10.Connect battery earth lead.
11.Check engine oil level and top-up if necessary.
M12 6614
M12 7917

ENGINE - K SERIES KV6
12-3-58 REPAIRS
Camshaft timing belt
$% 12.65.18
Remove
1.Disconnect battery earth lead.
2.Remove ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - KV6.
3.Remove RH front road wheel.
4.Remove 3 bolts securing RH splash shield to
body and remove shield.
5.Remove 3 bolts securing camshaft timing belt
LH rear cover and remove cover.
6.Remove inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - from 03MY.7.Remove 2 bolts securing RH rear timing belt
cover heat shield; remove heat shield.
8.Remove 3 bolts securing RH rear timing belt
cover; remove cover.
9.Using a socket on crankshaft pulley bolt, rotate
crankshaft in a clockwise direction. Align the
engine "SAFE" position, notch on crankshaft
pulley with the "ARROW" on front mounting
plate and the timing marks aligned on the rear
camshaft gears as illustrated.
CAUTION: Do not use camshaft gear bolts
or timing belt to rotate crankshaft.
M12 6614
M12 6694