2001 LAND ROVER FREELANDER alternator

PANEL REPAIRS
REPAIRS 77-2-61
Front roof assembly - 3 door
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove LH and RH front roof panel finishers.
5.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
6.Remove sunroof assembly.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
7.Remove windscreen.

+ SCREENS, REPAIRS, Windscreen.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. There are
no plug welds used in this procedure, spot
welds only.
Refit
1.Fit windscreen.

+ SCREENS, REPAIRS, Windscreen.
2.Fit sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
3.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
4.Fit LH and RH front roof panel finishers.
5.Connect all ECUs.
6.Connect alternator.
7.Connect battery earth lead.
Rear roof assembly - 3 door
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove soft/hard top.
5.Remove LH and RH rear roof panel finishers.
6.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
7.Remove sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
8.Remove aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 3 door.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. There are
no plug welds used in this procedure, spot
welds only.
Refit
1.Fit aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 3 door.
2.Fit sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
3.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
4.Fit LH and RH rear roof panel finishers.
5.Fit soft/hard top.
6.Connect all ECUs.
7.Connect alternator.
8.Connect battery earth lead.

Roof assembly - 5 door
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove tail door glass upper finisher.
5.Remove LH and RH roof panel finishers.

+ EXTERIOR FITTINGS, REPAIRS,
Moulding - roof - 5 door.
6.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
7.If applicable, remove sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 5 door.
8.Remove aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 5 door.
9.Remove windscreen.

+ SCREENS, REPAIRS, Windscreen.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown. Refit
1.Fit windscreen.

+ SCREENS, REPAIRS, Windscreen.
2.Fit aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 5 door.
3.If applicable, fit sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 5 door.
4.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
5.Fit LH and RH roof panel finishers.

+ EXTERIOR FITTINGS, REPAIRS,
Moulding - roof - 5 door.
6.Fit tail door glass upper finisher.
7.Connect all ECUs.
8.Connect alternator.
9.Connect battery earth lead.

AIR CONDITIONING
82-8REPAIRS
Refit
1.If a new compressor is being installed, drain the
required amount of refrigerant oil from the new
compressor.

+ GENERAL INFORMATION, Air
conditioning compressor replacement.
2.A new compressor is sealed and pressurised
with Nitrogen gas, slowly release the sealing
cap, gas pressure should be heard to release
as the seal is broken.
3.Clean compressor and mating face on front
mounting plate and cylinder block.
4.Position compressor, fit but do not fully tighten
lower bolt.
5.Position heat shield and fit compressor upper
securing bolts. Tighten compressor upper and
lower securing bolts to 25 Nm (18 lbf.ft).
6.Remove caps from compressor and high
pressure pipe.
7.Clean compressor high pressure pipe
connection.
8.Lubricate new 'O' ring with refrigerant oil and fit
to high pressure pipe.
9.Connect high pressure pipe to compressor, fit
and tighten bolt to 25 Nm (18 lbf.ft).
10.Connect multiplug to compressor.
11.Remove caps from compressor and low
pressure pipe.
12.Clean compressor low pressure pipe
connection.
13.Lubricate new 'O' ring with refrigerant oil and fit
to low pressure pipe.
14.Connect low pressure pipe to compressor, fit
and tighten bolt to 25 Nm (18 lbf.ft).
15.Clean pulley 'V's and tensioner pulley running
surface.
16.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
17.Fit splash shield and secure with bolts.
18.Fit RH road wheel and tighten nuts to 115 Nm
85 lbf.ft).
19.Replace receiver drier.

+ AIR CONDITIONING, REPAIRS,
Receiver drier.
20.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
21.Connect battery earth lead.
22.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
Compressor - K1.8
$% 82.10.20
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Recover refrigerant from A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
5.Remove alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - K1.8.
6.Disconnect multiplug from compressor.
7.Remove 2 bolts securing A/C pipes to
compressor, release A/C pipes from
compressor.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
8.Remove and discard 'O' rings from A/C pipes.

M82 0730

AIR CONDITIONING
REPAIRS 82-9
9.Remove 3 bolts securing compressor to
mounting bracket.
10.Release compressor from mounting bracket
and remove from under vehicle.
11.Drain oil from old compressor and record the
amount drained.Refit
1.If a new compressor is being installed, drain the
required amount of refrigerant oil from the new
compressor.

+ GENERAL INFORMATION, Air
conditioning compressor replacement.
2.A new compressor is sealed and pressurised
with Nitrogen gas, slowly release the sealing
cap, gas pressure should be heard to release
as the seal is broken.
3.Ensure mating faces of A/C pipes and
compressor are clean.
4.Lubricate new A/C pipe 'O' rings with clean
refrigerant oil.

+ GENERAL DATA, Air Conditioning.
5.Fit 'O' rings to A/C pipes.
6.Fit A/C compressor to mounting bracket. Fit
and tighten bolts to 25 Nm (18 lbf.ft).
7.Position compressor mounting bracket, fit bolts
and tighten to 25 Nm (18 lbf.ft).
8.Connect A/C compressor multiplug.
9.Fit alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - K1.8.
10.Replace receiver drier.

+ AIR CONDITIONING, REPAIRS,
Receiver drier.
11.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
12.Remove stands and lower vehicle.
13.Connect battery earth lead.
14.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
M82 0731

CHARGING AND STARTING
ADJUSTMENTS 86-1-1
CHARGING AND STARTING ADJUST ME NTS
Ancillary drive belt - K1.8
$% 86.10.05
Check
1.Disconnect battery earth lead.
2.Turn steering on RH lock.
3.Remove 3 bolts and remove splash shield.
4.Rotate crankshaft a sufficient number of turns
to check condition of drive belt. Renew a drive
belt that shows signs of wear, splitting or oil
contamination.
5.Apply a force of 10 kg to drive belt at position 'X'
and measure deflection between crankshaft
pulley and alternator pulley. Deflection must be
6 - 8 mm.Adjust
1.Loosen alternator pivot nut and bolt.
2.Loosen bolt securing alternator adjustment
bracket to engine.
3.Loosen bolt securing alternator to adjustment
bracket.
4.Increase drive belt tension by rotating
alternator adjustment bolt clockwise.
5.Tighten alternator pivot and adjustment bracket
bolts to 25 Nm (18 lbf.ft).
6.Recheck drive belt tension.
7.Fit splash shield and secure with bolts.
8.Straighten steering.
9.Connect battery earth lead.

CHARGING AND STARTING
REPAIRS 86-1-3
REPAIRS
Alternator - Td4
$% 86.10.02
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
3. Models with A/C: Remove compressor drive
belt.

+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
4.Remove 3 bolts securing coolant rail to sump
and cylinder block.
CAUTION: Care must be taken to ensure
that oil or fluid does not enter or
contaminate the alternator.
5. Models with A/C: Loosen bolt securing
compressor support bracket to sump, do not
remove.
6. Models with A/C: Remove 3 bolts securing
compressor to mounting bracket, release
support bracket and tie compressor aside.7. Models with A/C: Remove 3 bolts and bracket,
securing compressor mounting to casting on
cylinder block.
8.Disconnect alternator multiplug.
9.Remove nut securing battery cable to alternator
and remove cable.
10.Remove 3 bolts and remove alternator.
M86 5309
M86 5311

CHARGING AND STARTING
86-1-4 REPAIRS
Refit
1.Clean alternator mounting points.
2.Fit alternator to mounting bracket.Tighten M10
bolt to 45 Nm (33 lbf.ft) and M8 bolts to 25 Nm
(18 lbf.ft).
CAUTION: Ensure upper bolt is fitted prior
to assembly.
3.Connect alternator multiplug.
4.Fit battery cable to alternator terminal and
tighten to 10 Nm (7.5 lbf.ft).
5. Models with A/C: Clean A/C compressor and
housing mating faces, dowels and dowel holes.
6. Models with A/C: Fit bolts and compressor
mounting to casting, tighten to 25 Nm (18 lbf.ft).
7. Models with A/C: Position A/C compressor, fit
bolts and tighten to 25 Nm (18 lbf.ft).
8. Models with A/C: Align compressor support
bracket to sump and tighten bolt to 10 Nm (7.5
lbf.ft).
9.Fit lower coolant rail to sump and tighten bolts
to 10 Nm (7.5 lbf.ft).
10.Fit compressor drive belt.

+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
11.Refill cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
12.Connect battery earth lead.

CHARGING AND STARTING
REPAIRS 86-1-5
Alternator - KV6
$% 86.10.02
Remove
1.Disconnect battery earth lead.
2.Remove top arm.

+ ENGINE - K SERIES KV6, REPAIRS,
Arm assembly - engine mounting RH.
3.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and release drive
belt from alternator pulley.
4.Release alternator battery lead terminal cover,
loosen terminal nut and disconnect lead from
terminal
5.Disconnect alternator multiplug.
6.Remove lower bolt and upper nut and bolt
securing alternator to front mounting plate.
7.Remove alternator.Refit
1.Position alternator to front mounting plate.
2.Fit bolt and nut and bolt securing alternator to
front mounting plate and tighten to 45 Nm (33
lbf.ft).
3.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
4.Connect alternator multiplug.
5.Position battery cable to alternator, tighten nut
to 10 Nm (7.5 lbf.ft) and position terminal
cover.
6.Fit top arm.

+ ENGINE - K SERIES KV6, REPAIRS,
Arm assembly - engine mounting RH.
7.Connect battery earth lead.