2001 LAND ROVER FREELANDER lock

GENERAL DATA
04-13
⇒⇒ Grade C (Blue)*
⇒ Grade 9 57.665 - 57.659 mm (2.2703 - 2.2700 in.)
⇒⇒ Grade A (Black)
*
⇒⇒ Grade B (Yellow)*
⇒⇒ Grade C (Green)*
†
Cylinder block / bearing ladder bore diameter grades* Crankshaft big-end journal grades
Main bearings
Quantity 4
Material / type Glacier AS15 - oil grooves in upper half shells, plain lower half shells
Clearance in bearings 0.021 - 0.039 mm (0.0008 - 0.0015 in.)
Thrust washers:
⇒ Type / position Glacier AS15 - thrust washer halves at top and bottom of rear main
bearing, oil grooves in top and bottom halves
⇒ Thrust washer halves thickness 2.61 - 2.65 mm (0.103 - 0.104 in.)
Main bearing thickness:
⇒ Red 1.930 - 1.927 mm (0.0760 - 0.0759 in.)
⇒ Blue 1.927 - 1.924 mm (0.0759 - 0.0757 in.)
⇒ Green 1.924 - 1.921 mm (0.0757 - 0.0756 in.)
⇒ Yellow 1.921 - 1.918 mm (0.0756 - 0.0755 in.)
⇒ Black 1.918 - 1.915 mm (0.0755 - 0.0754 in.)
Big-end bearings
Material / Type Glacier AS15 - plain upper and lower half shells with locating tags
Clearance in bearings 0.022 - 0.040 mm (0.0009 - 0.0016 in.)
Big-end bearing thicknesses:
⇒ Red 1.803 - 1.800 mm (0.0710 - 0.0709 in.)
⇒ Blue 1.800 - 1.797 mm (0.0709 - 0.0707 in.)
⇒ Green 1.797 - 1.794 mm (0.0707 - 0.0706 in.)
⇒ Yellow 1.794 - 1.791 mm (0.0706 - 0.0705 in.)
⇒ Black 1.791 - 1.788 mm (0.0705 - 0.0704 in.)
Big-end end-float 0.19 - 0.29 mm (0.007 - 0.011 in.)
Connecting rods
Type Forged steel H-sections with horizontally split big-ends
Distance between centres 151.31 - 151.41 mm (5.957 - 5.961 in.)
Gudgeon pins
Type Semi-floating offset towards thrust side
Fit in connecting rods Interference
⇒ Diameter - Red coded 17.997 - 18.000 mm (0.7085 - 0.7087 in.)
⇒ Diameter - Green coded 17.994 - 17.997 mm (0.7084 - 0.7085 in.)
⇒ Length 52.3 - 52.6 mm (2.059 - 2.071 in.)
⇒ Clearance in piston 0.011 mm (0.0004 in.)
Pistons
Type Aluminium alloy, tin plated, thermal expansion with offset gudgeon pin
Piston diameter (at right angle to gudgeon pin and 10
mm (0.4 in. from bottom of skirt):
⇒ Grade A 79.965 - 79.980 mm (3.1482 - 3.1488 in.)
⇒ Grade B 79.981 - 79.995 mm (3.1489 - 3.1494 in.) General

GENERAL DATA
04-22
Manual Gearbox - PG1
Gear ratios:
⇒ First 3.250 : 1 (19.902 : 1 overall)
⇒ Second 1.894 : 1 (11.598 : 1 overall)
⇒ Third 1.222 : 1 (7.483 : 1 overall)
⇒ Fourth 0.848 : 1 (5.019 : 1 overall)
⇒ Fifth 0.649 : 1 (3.974 : 1 overall)
⇒ Reverse 3.000 : 1
Reverse idler gear to selector fork clearance 0.5 to 1.1 mm (0.020 - 0.043 in)
Selector fork prong width 13.0 to 13.3 mm (0.512 - 0.524 in)
Selector fork groove to pin clearance:
⇒ Standard 0.05 to 0.35 mm (0.002 - 0.014 in)
⇒ Service limit 0.50 mm (0.020 in)
Selector fork groove width 7.05 to 7.25 mm (0.278 - 0.285 in)
Gearshift arm to guide clearance:
⇒ Standard 0.20 to 0.30 mm (0.008 - 0.012 in)
⇒ Service limit 0.55 mm (0.022 in)
Interlock shift guide groove width 8.10 to 8.20 mm (0.319 - 0.323 in)
Synchro ring to gear clearance:
⇒ Standard 0.85 to 1.10 mm (0.033 - 0.043 in)
⇒ Service limit (minimum clearance) 0.40 mm (0.016 in)
Selector shaft forks in synchro sleeve grooves
clearance:
⇒ Standard 0.45 to 0.65 mm (0.018 - 0.026 in)
⇒ Service limit 1.00 mm (0.039 in)
Gearshift arm guide to selector fork clearance:
⇒ Standard 0.20 to 0.50 mm (0.008 - 0.020 in)
⇒ Service limit 0.80 mm (0.031 in)
Gearshift arm guide tongue width 11.90 to 12.00 mm (0.469 - 0.472 in)
Gearshift arm guide to interlock assembly clearance:
⇒ Standard 0.05 to 0.35 mm (0.002 - 0.014 in)
⇒ Service limit 0.60 mm (0.024 in)
Gearshift arm guide groove width 13.05 to 13.25 mm (0.514 - 0.522 in)
Interlock ball to gearshift arm guide clearance:
⇒ Standard 0.05 to 0.25 mm (0.002 - 0.010 in)
⇒ Service limit 0.50 mm (0.020 in)
Interlock ball outside diameter 12.05 to 12.15 mm (0.474 - 0.478 in)
2nd to 3rd gear clearance:
⇒ Standard 0.06 to 0.21 mm (0.002 - 0.008 in)
⇒ Service limit 0.30 mm (0.012 in)
3rd gear thickness:
⇒ Standard 35.42 to 35.47 mm (1.394 - 1.396 in)
⇒ Service limit 35.30 mm (1.390 in)

GENERAL DATA
04-25
Automatic Gearbox - Jatco
Gear Ratios - Td4 engine:
⇒ First 3.801:1
⇒ Second 2.131:1
⇒ Third 1.364:1
⇒ Fourth 0.935:1
⇒ Fifth 0.685:1
⇒ Reverse 2.970:1
Gear ratios - KV6 engine
⇒ First 3.474 : 1
⇒ Second 1.948 : 1
⇒ Third 1.247 : 1
⇒ Fourth 0.854 : 1
⇒ Fifth 0.685 : 1
⇒ Reverse 2.714 : 1
Final drive ratio:
⇒ Td4 engine
⇒ KV6 engine2.91 : 1
3.66 : 1
Torque converter lock-up
Td4
KV6Engaged in fourth and fifth gears.
50% throttle - 80 Kph (50 mph) in normal drive mode
50% throttle - 110 Kph (69 mph) in normal drive mode

GENERAL DATA
04-27
Steering
* The steering geometry settings are given in degrees and minutes, decimal parts of a degree and millimetres.
Steering and suspension geometry settings are for a vehicle at unladen weight.
Type Power assisted rack and pinion
Steering column Height adjustable by 3.5° or 30 mm vertical movement of steering
wheel
Turns - lock to lock 3.20
Turning circle: 11.38 m (37 ft 1.2 in) - with a 215/65 tyre
Overall ratio 19.5: 1
Wheel alignment*
Front
⇒ Camber angle (negative): -0° 15' ± 0° 45' (-0.25° ± 0.75°)
⇒ Cross camber angle 1° (1°) Maximum
⇒ Castor angle: 3° 30' ± 1° (3.92° ± 1.0°)
⇒ Cross castor angle 1° (1°) Maximum
⇒ King pin inclination 12° 18' (12.3°)
⇒ Front wheel alignment - total toe-out: - 0° 14' ± 0° 14' (- 0.23° ± 0.23°)
Rear
⇒ Camber angle (negative): -0° 30' ± 0° 45' (0.5° ± 0.75°)
⇒ Cross camber angle 1° (1°) Maximum
⇒ Thrust angle: 0° 0' ± 0° 6' (0° ± 0.10°)
⇒ Rear wheel alignment - total toe-in: 0° 20' ± 0° 15' (0.3° ± 0.25°)
Power assisted steering
Maximum Operating Pressure ( limited by pressure
relief valve in pump):
⇒ K1.8 90 - 100 bar (1305 - 1450 lbf/in
2)
⇒ KV6 & Td4 90 - 100 bar (1305 - 1450 lbf/in
2)
Pressure at idle 5 - 7 bar (72.5 - 101.5 lbf/in
2)
Maximum flow 5.5 ± 0.5 litres/min. (1.45 ± 0.13 US gal/min), limited by flow control
valve in pump

GENERAL DATA
04-31
Brakes
Front disc brakes
Type Pin-slider caliper with ventilated disc, self-adjusting
Disc diameter 262 mm (10.31 in)
Disc thickness:
⇒ New
⇒ Service limit20.8 - 21.00 mm (0.818 - 0.826 in)
18.00 mm (0.708 in)
Disc run-out (maximum) 0.040 mm (0.0016 in), with wheel on
Pad minimum thickness 3.00 mm (0.118 in)
Rear drum brakes
Drum inside diameter 254 mm (10.00 in)
Drum wear limit 255.49 mm (10.059 in), discard drum
Lining minimum thickness 2.00 mm (0.079 in)
Drum ovality limit 0.012 mm (0.0005 in)
Master cylinder
Bore diameter 23.80 mm (0.937 in)
Brake servo
Servo boost ratio 4.5 : 1
Parking brake
Type Mechanically operated via twin cables on rear drum brakes
Anti-lock braking system
Circuit type Diagonal split, dual circuit, 4-sensor ABS
ABS type TEVES MK20 with ABS, Hill Descent Control (HDC), Electronic
Traction Control (ETC) and Electronic Brakeforce Distribution (EBD)

IDENTIFICATION NUMBERS
05-2
Vehicle identification number -
Example: SALLNABG11A518779
Paint and trim colour codes
Paint code (F): a 3 digit code identifying the original
paint colour is stamped on the VIN plate.
Trim code (G):a code identifying the original trim
type and colour is stamped on the VIN plate.
Identification Number Locations
Engine number
K1.8 engine serial number is stamped on the front
face of the cylinder block adjacent to the gearbox.
K1.8 engines
KV6 engine serial number is stamped on the rear LH
side of the LH cylinder block.
KV6 engines
Td4 engine serial number is stamped on the bottom
LH side of the cylinder block.SALManufacturer's identifier (Land Rover UK)
LNMarque/Model
LN = Freelander
ATrim level
A = Trim level 1
BBody Style
B = 5 door models
GEngine
G = KV6 petrol engine models
1Transmission and Steering
1 = RHD automatic gearbox
1Model Year
1 = 2001 Model year
2 = 2002 Model year
3 = 2003 Model year
AAssembly plant
A = Solihull
6 figures= Serial number

TORQUE WRENCH SETTINGS
06-2
Engine – Td4
TORQUE DESCRIPTION METRIC IMPERIAL
Acoustic cover to engine 8 Nm 6 lbf.ft
Ancillary drive belt jockey pulley Allen bolt
*24 Nm 18 lbf.ft
Ancillary drive belt tensioner arm nut 10 Nm 7.5 lbf.ft
Big end bearing cap bolts:
⇒ Stage 15 Nm 3.5 lbf.ft
⇒ Stage 225 Nm 18 lbf.ft
⇒ Stage 3+70°+70°
Camshaft bearing cap bolts
† 10 Nm 7.5 lbf.ft
Camshaft cover bolts
† 10 Nm 7.5 lbf.ft
Camshaft sprocket retaining screw:
⇒ Stage 120 Nm 15 lbf.ft
⇒ Stage 2+35°+35°
Chain lubrication jet bolt 10 Nm 7.5 lbf.ft
Coolant rail to exhaust manifold bolts 20 Nm 15 lbf.ft
Coolant rail to exhaust manifold bolts 8 Nm 6 lbf.ft
Crankshaft pulley:
⇒ Stage 1100 Nm 74 lbf.ft
⇒ Stage 2+60 °+60 °
⇒ Stage 3+60 °+60 °
⇒ Stage 4+30 °+30 °
Crankshaft rear oil seal housing:
⇒ M6 bolts10 Nm 7.5 lbf.ft
⇒ M8 bolts22 Nm 16 lbf.ft
Cylinder block reinforcing plate 22 Nm 16 lbf.ft
Cylinder head bolts: (Stages 1 to 5 relate to bolts 1 to 11. Stage 6 is for bolt 12 only.)
⇒ Stage 1
†80 Nm 59 lbf.ft
⇒ Stage 2 - loosen all bolts
†-1/2 turn -1/2 turn
⇒ Stage 3
†50 Nm 37 lbf.ft
⇒ Stage 4
†+90°+90°
⇒ Stage 5
†+90°+90°
⇒ Stage 6 – tighten 41 mm bolt in position 12 110 Nm 81 lbf.ft
Cylinder head to timing cover Allen screws 15 Nm 11 lbf.ft
Dipstick tube to oil filter housing bolt 10 Nm 7.5 lbf.ft
Drive plate to crankshaft bolts
† 115 Nm 85 lbf.ft
EGR cooler to cylinder head and lifting bracket bolts 25 Nm 18 lbf.ft
Engine breather pipe to air cleaner housing bolt 10 Nm 7.5 lbf.ft
Engine lifting eye bolts 20 Nm 15 lbf.ft
Engine mounting bracket assembly to engine bolts 100 Nm 74 lbf.ft
Engine mounting bracket to hydramount nut 85 Nm 63 lbf.ft
Engine lower steady bracket bolts:
⇒ M1045 Nm 33 lbf.ft
⇒ M1250 Nm 37 lbf.ft
Engine steady mounting bolt 100 Nm 74 lbf.ft
Exhaust manifold to cylinder head nuts 24 Nm 18 lbf.ft
Flywheel to crankshaft bolts
† 115 Nm 85 lbf.ft
Fuel pipe bracket to oil filter housing bolt 10 Nm 7.5 lbf.ft
Fuel pipe union nuts 30 Nm 22 lbf.ft
Fuel pump drive chain lower guide Allen bolt 24 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-3
† Tighten in sequence
* Fit new bolt
Fuel pump sprocket retaining nut 65 Nm 48 lbf.ft
Fuel rail Allen screws 24 Nm 18 lbf.ft
Fuel rail to coolant rail bolts 10 Nm 7.5 lbf.ft
Fuel rail to support bracket bolts 10 Nm 7.5 lbf.ft
Glow plugs18 Nm 13 lbf.ft
Heatshield to coolant rail Allen screws 8 Nm 6 lbf.ft
Hose adaptor to cylinder head bolts 8 Nm 6 lbf.ft
LH engine mounting to gearbox bracket through bolt 100 Nm 74 lbf.ft
LH engine mounting to body 45 Nm 33 lbf.ft
Lower coolant rail support bracket bolts 15 Nm 11 lbf.ft
Main bearing cap bolts:
⇒ 1st. Stage
† 20 Nm 15 lbf.ft
⇒ 2nd Stage
† +70°+70°
Oil cooler to oil filter housing bolts 22 Nm 16 lbf.ft
Oil feed guide rail bolts 10 Nm 7.5 lbf.ft
Oil filter cap25 Nm 18 lbf.ft
Oil filter housing bolts 25 Nm 18 lbf.ft
Oil pick-up strainer to oil pump bolts 10 Nm 7.5 lbf.ft
Oil pressure switch 38 Nm 28 lbf.ft
Oil pump drive gear to oil pump drive shaft Torx bolt 25 Nm 18 lbf.ft
Oil pump to cylinder block 25 Nm 18 lbf.ft
PAS pipe clip to engine lifting eye bolt 10 Nm 7.5 lbf.ft
Sump: †
⇒ M6 bolts10 Nm 7.5 lbf.ft
⇒ M8 bolts28 Nm 21 lbf.ft
Sump drain plug28 Nm 21 lbf.ft
Sump plate bolts10 Nm 7.5 lbf.ft
Timing chain support guides 20 Nm 15 lbf.ft
Timing chain tensioner access plug 30 Nm 22 lbf.ft
Timing chain tensioner bolt 10 Nm 7.5 lbf.ft
Timing cover bolts
† 15 Nm 11 lbf.ft
Turbocharger to exhaust manifold bolts 45 Nm 33 lbf.ft
Turbocharger outlet pipe fixing bolts:
⇒ 6mm10 Nm 7.5 lbf.ft
⇒ 8mm25 Nm 18 lbf.ft
Vacuum pump bolts 22 Nm 16 lbf.ft