2001 LAND ROVER FREELANDER battery replacement

PANEL REPAIRS
REPAIRS 77-2-57
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown. Refit
1. LH side: Fit tail door striker.
2. RH side: Fit fuel tank.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Tank - Non NAS.
3. RH side: Fit fuel filler neck.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Filler neck.
4. RH side: Fit tail door.

+ DOORS, REPAIRS, Door - tail
assembly - remove for access & refit.
5.Secure vehicle harness to 'E' post.
6.Fit rear body side glass.

+ SCREENS, REPAIRS, Glass - body
side - rear.
7.Fit loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
8.Fit rear quarter upper casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
9.Fit rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
10.Fit tail door aperture seal.
11.Fit tail door glass side finisher.

+ DOORS, REPAIRS, Finisher - rear
screen - side - 5 door.
12.Fit tail door glass upper finisher.
13.Fit roof panel finisher.

+ DOORS, REPAIRS, Finisher - rear
screen - side - 5 door.
14.Fit tail lamp.

+ LIGHTING, REPAIRS, Lamp
assembly - tail.
15.Fit rear wheel arch liner.
16.Fit rear bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper valance - rear - up to 04MY.
17.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
18.Connect all ECUs.
19.Connect alternator.
20.Connect battery earth lead.

PANEL REPAIRS
77-2-58 REPAIRS
Rear floor crossmember assembly
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove tail door.

+ DOORS, REPAIRS, Door - tail
assembly - remove for access & refit.
5.Remove tail door aperture seal.
6.Remove LH and RH rear quarter lower casings.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
7.Remove loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
8.Release vehicle harness from rear body lower
closing and position aside.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown. Refit
1.Secure vehicle harness to rear body lower
closing.
2.Fit loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
3.Fit LH and RH rear quarter lower casings.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
4.Fit tail door aperture seal.
5.Fit tail door.

+ DOORS, REPAIRS, Door - tail
assembly - remove for access & refit.
6.Connect all ECUs.
7.Connect alternator.
8.Connect battery earth lead.

PANEL REPAIRS
REPAIRS 77-2-59
Rear floor
In this procedure, the inner quarter to rear floor
gussets are replaced in conjunction with the rear
floor. If required, the safe well can be replaced
separately.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove tail exhaust pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- Td4, REPAIRS, Exhaust pipe - tail.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES 1.8, REPAIRS, Exhaust pipe -
tail.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Tail pipe &
silencer.
5.Remove tail door.

+ DOORS, REPAIRS, Door - tail
assembly - remove for access & refit.
6.Remove tail door aperture seal.
7.Remove LH and RH rear quarter lower casings.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
8.Remove loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
9.Remove fuel tank.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Tank - Non NAS.
10.Release vehicle harness from rear body lower
closing and position aside. Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
Refit
1.Secure vehicle harness to rear body lower
closing.
2.Fit fuel tank.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Tank - Non NAS.
3.Fit loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
4.Fit LH and RH rear quarter lower casings.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
5.Fit tail door aperture seal.
6.Fit tail door.

+ DOORS, REPAIRS, Door - tail
assembly - remove for access & refit.
7.Fit tail exhaust pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- Td4, REPAIRS, Exhaust pipe - tail.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES 1.8, REPAIRS, Exhaust pipe -
tail.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Tail pipe &
silencer.
8.Connect all ECUs.
9.Connect alternator.
10.Connect battery earth lead.

PANEL REPAIRS
77-2-60 REPAIRS
Floor longitudinal
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove tail exhaust pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- Td4, REPAIRS, Exhaust pipe - tail.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES 1.8, REPAIRS, Exhaust pipe -
tail.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Tail pipe &
silencer.
5.Remove tail door.

+ DOORS, REPAIRS, Door - tail
assembly - remove for access & refit.
6.Remove tail door aperture seal.
7.Remove LH and RH rear quarter lower casings.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
8.Remove loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
9.Remove fuel tank.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Tank - Non NAS.
10.Release vehicle harness from rear body lower
closing and position aside. Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
Refit
1.Secure vehicle harness to rear body lower
closing.
2.Fit fuel tank.
+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Tank - Non NAS.
3.Fit loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
4.Fit LH and RH rear quarter lower casings.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
5.Fit tail door aperture seal.
6.Fit tail door.

+ DOORS, REPAIRS, Door - tail
assembly - remove for access & refit.
7.Fit tail exhaust pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- Td4, REPAIRS, Exhaust pipe - tail.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES 1.8, REPAIRS, Exhaust pipe -
tail.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Tail pipe &
silencer.
8.Connect all ECUs.
9.Connect alternator.
10.Connect battery earth lead.

PANEL REPAIRS
REPAIRS 77-2-61
Front roof assembly - 3 door
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove LH and RH front roof panel finishers.
5.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
6.Remove sunroof assembly.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
7.Remove windscreen.

+ SCREENS, REPAIRS, Windscreen.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. There are
no plug welds used in this procedure, spot
welds only.
Refit
1.Fit windscreen.

+ SCREENS, REPAIRS, Windscreen.
2.Fit sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
3.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
4.Fit LH and RH front roof panel finishers.
5.Connect all ECUs.
6.Connect alternator.
7.Connect battery earth lead.
Rear roof assembly - 3 door
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove soft/hard top.
5.Remove LH and RH rear roof panel finishers.
6.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
7.Remove sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
8.Remove aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 3 door.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. There are
no plug welds used in this procedure, spot
welds only.
Refit
1.Fit aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 3 door.
2.Fit sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
3.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
4.Fit LH and RH rear roof panel finishers.
5.Fit soft/hard top.
6.Connect all ECUs.
7.Connect alternator.
8.Connect battery earth lead.

Roof assembly - 5 door
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove tail door glass upper finisher.
5.Remove LH and RH roof panel finishers.

+ EXTERIOR FITTINGS, REPAIRS,
Moulding - roof - 5 door.
6.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
7.If applicable, remove sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 5 door.
8.Remove aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 5 door.
9.Remove windscreen.

+ SCREENS, REPAIRS, Windscreen.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown. Refit
1.Fit windscreen.

+ SCREENS, REPAIRS, Windscreen.
2.Fit aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 5 door.
3.If applicable, fit sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 5 door.
4.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
5.Fit LH and RH roof panel finishers.

+ EXTERIOR FITTINGS, REPAIRS,
Moulding - roof - 5 door.
6.Fit tail door glass upper finisher.
7.Connect all ECUs.
8.Connect alternator.
9.Connect battery earth lead.

AIR CONDITIONING
82-6REPAIRS
Compressor - Td4
$% 82.10.20
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Disconnect battery earth lead.
3.Recover refrigerant from A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
4.Remove compressor drive belt.

+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
WARNING: Under no circumstances should
refrigerant hoses be disconnected without
first discharging the system.
5.Remove 2 bolts securing A/C pipes to
compressor. Release pipes from compressor.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
6.Remove and discard 'O' rings from A/C pipes.7.Loosen bolt securing compressor support
bracket to sump, do not remove.
8.Remove 3 bolts and remove compressor from
mounting bracket. Move support strap aside,
disconnect compressor multiplug and remove
compressor.
Refit
1.If a new compressor is being installed, drain the
required amount of refrigerant oil from the new
compressor.

+ GENERAL INFORMATION, Air
conditioning compressor replacement.
2.A new compressor is sealed and pressurised
with Nitrogen gas, slowly release the sealing
cap, gas pressure should be heard to release
as the seal is broken.
3.Ensure mating faces of A/C pipes and
compressor are clean.
4.Fit A/C compressor to mounting bracket, align
support strap and tighten bolts to 25 Nm (18
lbf.ft).
5.Connect multiplug to compressor.
6.Lubricate new 'O' rings with clean refrigerant oil
and fit to evaporator pipes
7.Position A/C pipes to compressor, fit bolts and
tighten to 22 Nm (16 lbf.ft).
8.Replace receiver drier.

+ AIR CONDITIONING, REPAIRS,
Receiver drier.
9.Fit compressor drive belt.

+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
10.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
11.Connect battery earth lead.
12.Remove stands and lower vehicle.

AIR CONDITIONING
82-8REPAIRS
Refit
1.If a new compressor is being installed, drain the
required amount of refrigerant oil from the new
compressor.

+ GENERAL INFORMATION, Air
conditioning compressor replacement.
2.A new compressor is sealed and pressurised
with Nitrogen gas, slowly release the sealing
cap, gas pressure should be heard to release
as the seal is broken.
3.Clean compressor and mating face on front
mounting plate and cylinder block.
4.Position compressor, fit but do not fully tighten
lower bolt.
5.Position heat shield and fit compressor upper
securing bolts. Tighten compressor upper and
lower securing bolts to 25 Nm (18 lbf.ft).
6.Remove caps from compressor and high
pressure pipe.
7.Clean compressor high pressure pipe
connection.
8.Lubricate new 'O' ring with refrigerant oil and fit
to high pressure pipe.
9.Connect high pressure pipe to compressor, fit
and tighten bolt to 25 Nm (18 lbf.ft).
10.Connect multiplug to compressor.
11.Remove caps from compressor and low
pressure pipe.
12.Clean compressor low pressure pipe
connection.
13.Lubricate new 'O' ring with refrigerant oil and fit
to low pressure pipe.
14.Connect low pressure pipe to compressor, fit
and tighten bolt to 25 Nm (18 lbf.ft).
15.Clean pulley 'V's and tensioner pulley running
surface.
16.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
17.Fit splash shield and secure with bolts.
18.Fit RH road wheel and tighten nuts to 115 Nm
85 lbf.ft).
19.Replace receiver drier.

+ AIR CONDITIONING, REPAIRS,
Receiver drier.
20.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
21.Connect battery earth lead.
22.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
Compressor - K1.8
$% 82.10.20
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Recover refrigerant from A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
5.Remove alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - K1.8.
6.Disconnect multiplug from compressor.
7.Remove 2 bolts securing A/C pipes to
compressor, release A/C pipes from
compressor.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
8.Remove and discard 'O' rings from A/C pipes.

M82 0730