2001 LAND ROVER FREELANDER wheel alignment

STEERING
57-24 REPAIRS
Track rod
$% 57.55.09
Remove
1. Td4 & KV6 models: Remove steering rack.

+ STEERING, REPAIRS, Power
steering rack.
2.Remove Torx bolt securing track rod to PAS
rack. Discard Torx bolt.
3.Remove track rod and spacer.
CAUTION: Note orientation of spacers
before dismantling.
4.Hold track rod securely and loosen pinch bolt in
track rod end.
NOTE: Do not carry out further dismantling if
component is removed for access only.
5.Remove ball joint, note the number of turns for
refit.
6. Remove pinch bolt from track rod.
7.Remove turnbuckle and note the number of
turns for refit.
NOTE: Thread is left handed.Refit
1.Fit turnbuckle to track rod to number of turns on
remove.
2.Fit pinch bolt but do not tighten at this stage.
3.Fit ball joint to turnbuckle to number of turns
noted in remove.
4.Fit pinch bolt but do not tighten at this stage.
CAUTION: Ensure slots in turn buckle
clamps are aligned.
5.Clean spacer, support plate and track rod ball
joint.
6.Fit spacer to rack.
CAUTION: Ensure spacers are aligned and
fitted correctly.
7.Fit track rod to PAS rack.
8.Hold track rod parallel to PAS rack, fit new Torx
bolt and tighten to 100 Nm (74 lbf.ft).
9. Td4 & KV6 models: Fit steering rack.

+ STEERING, REPAIRS, Power
steering rack.
10.Check and adjust front wheel alignment.

+ STEERING, ADJUSTMENTS, Front
wheel alignment - check & adjust.
WARNING: Ensure all track rod pinch bolts
are tightened to the correct torque on
completion of the front wheel alignment
check.

FRONT SUSPENSION
60-10 REPAIRS
Refit
1.Inspect damper, spring mounting rubbers and
bearing for deterioration and damage.
2.Clean mating faces of spring, mounting and
mounting plate.
3.Clean damper shaft and bump stop plate.
4.Position spring and damper assembly to spring
compressor. Compress spring.
5.Fit damper to spring, ensure spring locates in
cut recess in damper plate.
6.Fit bump cup, bump stop and dust cover to
damper.
7.Fit spring aid and bump plate.
8.Fit mounting plate and rebound washer.
9.Using new nut, hold damper shaft with Allen
key and tighten nut to 57 Nm (42 lbf.ft).
CAUTION: Note alignment of top mounting,
spring and damper dust cover.
10.Release and remove spring from compressor.
11.Clean mating face of top mounting plate.
12.Position damper assembly and align top
mounting to body, fit nuts and tighten to 45 Nm
(33 lbf.ft).
13. LH side: Position fusebox, fit nuts and tighten
to 8 Nm (6 lbf.ft).
14. LH side: Connect positive and negative leads,
fit bolts and tighten to 8 Nm (6 lbf.ft).
15. LH side: Connect multiplug to fusebox.
16. RH side: Position coolant reservoir and secure
with bolt.
17.Fit hub to damper, fit nuts and bolts and tighten
to 205 Nm (151 lbf.ft).
18.Clean anti-roll bar link taper and mating face.
19.Connect anti-roll bar link, fit new nut and tighten
to 55 Nm (41 lbf.ft).
CAUTION: Use a spanner and an Allen key
to prevent ball joint rotating when undoing
link.
20.Clean track rod taper and mating face.
21.Connect track rod end to steering arm using
new nut and tighten nut to 55 Nm (41 lbf.ft).
22.Clean ABS sensor, smear sensor with an anti-
seize grease and fit sensor to hub.
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
pole wheel teeth.
23.Position ABS harness and brake hose in
bracket and secure with clip.
24.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
25.Remove stand and lower vehicle.
26.Connect battery earth lead.
Lower arm assembly
$% 60.35.02
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Release stake in drive shaft nuts.
5.With an assistant applying brakes, remove and
discard drive shaft hub nut.
6.Remove clip securing brake hose to bracket on
damper.
7.Release ABS sensor harness and brake hose
from damper.
8.Release ABS sensor from hub.

FRONT SUSPENSION
60-14 REPAIRS
Refit
1.Position and align beam, fit new bolts securing
beam to body but do not fully tighten at this
stage.
2.Locate lower arm bushes, fit but do not fully
tighten bolts.
CAUTION: Nuts and bolts must be tightened
with weight of vehicle on suspension.
3.Clean bush housing and mating faces on
beam.
4.Align bush housings ensuring roll pin is
correctly located. Fit bolts and tighten to 105
Nm (77 lbf.ft).
5.Tighten bolts securing beam to body to 190 Nm
(140 lbf.ft).
6.Fit saddle clamp bolts and tighten to 23 Nm (17
lbf.ft).
7.Align engine lower steady, fit bolt and tighten to
100 Nm (74 lbf.ft).
8.Lower vehicle.
9.Tighten lower arm front bush bolts to 190 Nm
(140 lbf.ft).
10.Tighten lower arm rear bush nuts to 140 Nm
103 lbf.ft).
11.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
12.Check and if necessary adjust wheel
alignment.

FRONT SUSPENSION
REPAIRS 60-15
Bush - lower arm - front
$% 60.35.24
Remove
1.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove 2 bolts securing rear bush housing to
rear beam.
4.Release rear bush housing from body dowel.
5.Remove bolt securing lower arm front
mounting.
6.Release lower arm front mounting from rear
beam.
7.Using LRT-60-008 and adaptors remove lower
arm bush.Refit
1.Ensure bush bore in hub is clean.
2.Using LRT-60-008 fit new bush into lower arm.
3.Align lower arm to rear beam, fit bolt but do not
tighten at this stage.
4.Align rear bush housing to body dowel, fit bolts
but do not tighten at this stage.
5.Tighten rear bush housing bolts to 105 Nm (77
lbf.ft).
CAUTION: Nuts and bolts must be tightened
with the weight of the vehicle on the
suspension.
6.Tighten lower arm front bush bolts to 190 Nm
(140 lbf.ft).
7.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
8.Remove stands and lower vehicle.
9.Check and, if necessary, adjust wheel
alignment.

+ STEERING, ADJUSTMENTS, Front
wheel alignment - check & adjust.

FRONT SUSPENSION
60-16 REPAIRS
Bush - lower arm - rear
$% 60.35.25
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove nut securing lower arm rear bush
housing and remove snubber rubber.
CAUTION: Note orientation of snubber
washer.
3.Remove 2 bolts securing lower arm rear bush
housing.
4.Release bush locating pin from body and
remove bush housing.Refit
1.Clean lower arm and bush housing mating
faces.
2.Fit bush housing to lower arm and locate dowel
into body.
3.Fit bolts securing lower arm rear bush
housings and tighten to 105 Nm (77 lbf.ft).
4.Fit snubber rubber and nut but do not tighten at
this stage.
CAUTION: Ensure correct orientation of
snubber washer. Ensure that 'OUT' is
visible on snubber washer when fitted.
5.Tighten rear bush housing nut to 140 Nm (103
lbf.ft).
CAUTION: Nuts and bolts must be tightened
with the weight of the vehicle on the
suspension.
6.Remove stand and lower vehicle.
7.Check front wheel alignment.

+ STEERING, ADJUSTMENTS, Front
wheel alignment - check & adjust.

REAR SUSPENSION
REPAIRS 64-1
REAR SUSPENSION REPAIRS
Bush - trailing link
$% 64.15.11
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove nut and bolt securing trailing link to
rear hub, collect spacer from under bolt head.
4.Release trailing link from hub and tie aside.
5.Using LRT-64-002 remove trailing link bush
from hub.Refit
1.Ensure bush bore in hub is clean.
2.Using LRT-64-002 fit new bush into hub.
3.Align trailing link to hub, fit nut and bolt but do
not tighten at this stage.
4.Support weight of vehicle with jack under rear
hub.
CAUTION: Nuts and bolts must be tightened
with weight of vehicle on suspension.
5.Fit spacer, nut and bolt to trailing link and
tighten to 120 Nm (89 lbf.ft).
6.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
7.Remove stands and lower vehicle.
8.Check and, if necessary, adjust wheel
alignment.

REAR SUSPENSION
REPAIRS 64-7
17.Remove cover from top mounting.
18.Compress spring by 2 to 3 cm until loose, hold
damper shaft with Allen key, remove and
discard mounting plate nut.
19.Remove top mounting plate.
20.Remove rebound washer and mounting plate.
21.Remove spring aid and bump plate.
22.Remove spring seat, dust cover and bump stop
cup.
23.Remove damper from spring.
24.Release and remove spring from compressor.Refit
1.Inspect damper, spring mounting rubbers and
bearing for deterioration and damage.
2.Clean mating faces of spring, mounting and
mounting plate.
3.Clean damper shaft and bump stop plate.
4.Position spring and damper assembly to spring
compressor. Compress spring.
5.Fit damper to spring, ensure spring locates in
cut recess in damper plate.
6.Fit bump stop, bump stop cup and dust cover to
damper.
7.Fit spring aid and bump plate.
8.Fit mounting plate and rebound washer.
9.Using new nut, hold damper shaft with Allen
key and tighten nut to 57 Nm (42 lbf.ft).
CAUTION: Note alignment of top mounting,
spring and damper dust cover.
10.Fit top mounting cover.
11.Release and remove spring from compressor.
12.Clean mating face of top mounting plate.
13.Fit rubber seal to top mounting.
14.Position damper assembly and align top
mounting to body, fit nuts and tighten to 45 Nm
(33 lbf.ft).
15.Fit rear quarter lower trim casings.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 3 door.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
16.Fit hub to damper and tighten bolts to 205 Nm
(151 lbf.ft).
17.Clean ABS sensor, smear sensor with an anti-
seize grease and fit sensor to hub.
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
pole wheel teeth.
18.Secure brake hose and ABS sensor harness to
damper.
19.Secure brake hose with 'C' clip.
20.Remove plugs and clean brake pipe male end.
21.Align hose to brake pipe and tighten union to 14
Nm (10 lbf.ft).
22.Remove clamp from brake hose.
23.Bleed brake system.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
24.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
25.Remove stands and lower vehicle.

REAR SUSPENSION
64-8 REPAIRS
Trailing arm
$% 64.35.46
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove nut and bolt securing trailing link to
hub.
4.Remove bolt securing trailing link to bracket.
5.Remove trailing link.Refit
1.Fit trailing link.
2.Fit bolt to bracket but do not tighten at this
stage.
3.Align trailing link to hub, fit nut and bolt but do
not tighten at this stage.
4.Support weight of vehicle with jack under rear
hub.
CAUTION: Nuts and bolts must be tightened
with weight of vehicle on suspension.
5.Tighten nuts and bolts to 120 Nm (89 lbf.ft).
6.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
7.Remove stands and lower vehicle.
8.Check and if necessary adjust rear wheel
alignment.