2001 LAND ROVER FREELANDER timing belt

TORQUE WRENCH SETTINGS
06-7
† Tighten in sequence
*New bolts must be fitted
+ Apply sealant, Part No. STC50552 to threads
++ Apply sealant, Part No. STC 4600 to threads
+++ Apply sealant, Part No. STC 50550 to threads
Ignition coils to LH inlet manifold nut and bolts 9 Nm 7 lbf.ft
Ignition plug top coils to spark plug bolts 9 Nm 7 lbf.ft
Inlet manifold to cylinder head nuts and bolts 25 Nm 18 lbf.ft
IRD support bracket to front mounting plate bolts 45 Nm 33 lbf.ft
IRD support bracket to sump bolts 45 Nm 33 lbf.ft
LH mounting to body bolts 48 Nm 35 lbf.ft
LH mounting bracket to gearbox bolts 85 Nm 63 lbf.ft
LH mounting to gearbox bracket through bolt 100 Nm 74 lbf.ft
Oil cooler to sump mounting bracket nuts 25 Nm 18 lbf.ft
Oil cooler pipes to oil filter and oil cooler unions 26 Nm 19 lbf.ft
Oil dipstick tube bracket to cylinder block bolt 9 Nm 7 lbf.ft
Oil pick-up strainer to bearing ladder bolts
+8 Nm 6 lbf.ft
Oil pressure relief valve plug nut
+25 Nm 18 lbf.ft
Oil pressure switch 14 Nm 10 lbf.ft
Oil pump to cylinder block bolts
†
⇒ Stage 1
⇒ Stage 25 Nm
9 Nm4 lbf.ft
7 lbf.ft
PAS pipe to engine front mounting plate bolt 25 Nm 18 lbf.ft
PAS pipe support bracket to RH hydramount nut 85 Nm 63 lbf.ft
Sump to lower crankcase bolts
†++35 Nm 26 lbf.ft
Timing belt cover (front LH and RH) bolts 4 Nm 3 lbf.ft
Timing belt cover (lower) to cylinder block bolts 9 Nm 7 lbf.ft
Timing belt cover (rear LH and RH) bolts 4 Nm 3 lbf.ft
Rear timing belt cover backplate bolts 9 Nm 7.5 lbf.ft
Top arm to RH hydramount nut 85 Nm 63 lbf.ft
Top arm bracket to engine front plate and RH mounting bolts 100 Nm 74 lbf.ft

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-4
Sealants
The following table lists those sealants which are
used during repair / overhaul procedures covered in
this manual; it is essential that the sealant specified
for a particular procedure is used at all times.
Component Application Land Rover
Part No.
Td4 Engine Camshaft cover
gasket joint linesSTC 50550
Td4 Engine Sump gasket joint
linesSTC 50550
K 1.8 Engine Oil pressure switch
threadsSTC 50552
K 1.8 Engine Oil pressure relief
valve plug threadsSTC 50552
K 1.8 Engine Oil temperature
sensor threadsSTC 50552
K 1.8 Engine Oil pump cover
plate screwsSTC 50552
K 1.8 Engine Camshaft carrier to
cylinder headSTC 4600
K 1.8 Engine Bearing ladder to
cylinder blockSTC 4600
K 1.8 Engine Sump to bearing
ladderSTC 4600
K 1.8 Engine Oil rail to bearing
ladderSTC 4600
K 1.8 Engine Crankshaft rear oil
seal STC 50550
K 1.8 Engine Cylinder liners to
cylinder blockRTC 3347
KV6 Engine Camshaft timing
belt backplate
cover boltsSTC 50552
KV6 Engine Oil pressure relief
valve plug threadsSTC 50552
KV6 Engine Oil pump cover
plate screwsSTC 50552
KV6 Engine Camshaft carrier to
cylinder headSTC 4600
KV6 Engine Sump to lower
crankcaseSTC 4600
KV6 Engine Oil pick-up strainer
boltSTC 50552
KV6 Engine Lower crankcase to
cylinder blockSTC 50550
KV6 Engine Cylinder liners to
cylinder blockRTC 3347
KV6 Engine Coolant stub pipe to
cylinder blockSTC 50554
Engine
Management
System -
MEMSSensor - Engine
Coolant
temperature (ECT)STC 50552
Cooling
System - KV6Cylinder block drain
plugSTC 50552
Manual
Gearbox - PG12 top bolts -
gearbox to engineSTC 50552
Manual
Gearbox -
GetragRear cover to
gearcaseSTC 4600
Manual
Gearbox -
GetragGearshift cover STC 4600
Intermediate
Reduction
DriveEnd cover gasket -
IRD housingSTC 4600
Automatic
Gearbox -
JatcoFluid pan to
gearcaseSTC 4600
Rear Axle and
Final DriveDifferential cover to
casingSTC 3811

MAINTENANCE
MAINTENANCE 10-15
Ancillary Drive Belt – KV6
Check
1.Check ancillary drive belts for tension, signs of
fraying, damage and for any oil contamination.
Replace
1.Replace ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - KV6.
Camshaft Timing Belt – K1.8
Check
1.Check camshaft drive belt and renew if
necessary.

+ ENGINE - K SERIES 1.8, REPAIRS,
Camshaft timing belt.

MAINTENANCE
10-16 MAINTENANCE
Camshaft Timing Belt – KV6
Check
1.Check camshaft drive belt and renew if
necessary.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
Brake/Clutch Reservoir
Check/Top-up
RHD shown, LHD similar
1.Check fluid level in brake/clutch fluid reservoir.
2.Clean area around filter cap, remove cap.
3.Top-up if necessary to correct level on reservoir
using recommended fluid.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS, Fluids.
4.Fit filler cap.

ENGINE - K SERIES KV6
REPAIRS 12-3-3
REPAIRS
Camshafts - LH cylinder head
$% 12.13.02
Remove
1.Disconnect battery earth lead.
2.Remove camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
3.Remove LH camshaft rear timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft rear timing belt - LH cylinder
head.
4.Remove LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
5.Remove 4 bolts and remove front camshaft
drive belt cover backplate from cylinder head.
6.Remove 2 bolts securing LH rear camshaft
drive belt cover backplate to cylinder head and
remove backplate.7.Using sequence shown, progressively loosen
22 bolts securing camshaft carrier to cylinder
head until valve spring pressure is released,
remove bolts.
8.Release camshaft carrier from dowels and
remove carrier.
9.Remove camshafts and discard oil seals.
10.Using a stick magnet, remove 12 hydraulic
tappets from cylinder head.
CAUTION: Store hydraulic tappets in their
fitted order and store upright. Maintain
absolute cleanliness when handling
hydraulic tappets. Failure to observe these
precautions can result in engine failure.
11.Clean camshafts and bearing running surfaces
in camshaft carrier and cylinder head.
12.Inspect camshafts and replace camshafts if
scored, pitted or excessively worn.
Note: Camshafts are colour coded - Inlet -
ORANGE; Exhaust - BLUE.
M12 6905
M12 6906

ENGINE - K SERIES KV6
12-3-4 REPAIRS
Refit
1.Thoroughly clean and lubricate hydraulic
tappets with clean engine oil. Fit hydraulic
tappets to original bores in cylinder head.
2.Ensure that mating faces of camshaft carrier
and cylinder head are clean and dry.
3.Lubricate camshafts and bearing journals with
clean engine oil.
4.Position camshafts in cylinder head with rear
timing gear drive slots in each camshaft facing
towards the centre as shown.
CAUTION: Ensure camshafts are in their
correct fitted locations, camshafts are
colour coded - Inlet - ORANGE; Exhaust -
BLUE.
5.Apply continuous thin beads of sealant, Part
No. STC 4600, to paths on camshaft carrier as
shown. Spread sealant to an even film using a
roller.
CAUTION: Ensure sealant does not enter oil
feed holes or grooves and that assembly is
completed within 20 minutes.6.Position camshaft carrier, fit and progressively
tighten bolts in the sequence shown to 10 Nm
(7.5 lbf.ft).
7.Noting that the front camshaft oil seals are
black in colour and the rear oil seals are red, fit
new camshaft oil seals using LRT-12-203 and
LRT-12-148A
CAUTION: Oil seals must be fitted dry. Do
not use tool LRT-12-148 for fitting seals.
8.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.
9.Position camshaft timing belt rear cover
backplates to cylinder head, fit and tighten bolts
to 9 Nm (7 lbf.ft).
10.Fit LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
11.Fit camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.

ENGINE - K SERIES KV6
REPAIRS 12-3-5
12.Fit LH camshaft rear timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft rear timing belt - LH cylinder
head.
13.Top-up engine oil.

+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.
14.Connect battery earth lead.
Camshafts - RH cylinder head
$% 12.13.03
Remove
1.Disconnect battery earth lead.
2.Remove camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
3.Remove RH rear camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft rear timing belt - RH cylinder
head.
4.Remove RH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - RH.
5.Remove 4 bolts securing RH front timing belt
cover backplate to cylinder head and remove
backplate.
6.Remove 2 bolts securing RH rear timing belt
cover backplate and remove backplate.
M12 6903
M12 6904

ENGINE - K SERIES KV6
REPAIRS 12-3-7
6.Position camshaft carrier, fit and progressively
tighten bolts in the sequence shown to 10 Nm
(7.5 lbf.ft).
7.Noting that the front camshaft oil seals are
black in colour and the rear oil seals are red, fit
new camshaft oil seals using LRT-12-203 and
LRT-12-148A
CAUTION: Oil seals must be fitted dry. Do
not use tool LRT-12-148 for fitting seals. 8.Clean camshaft timing cover backplate bolts
and apply sealant, Part No. STC 50552 to first
3 threads.
9.Fit camshaft cover backplates fit and tighten
bolts to 9 Nm (7 lbf.ft).
10.Fit RH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - RH.
11.Fit camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
12.Fit RH rear camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft rear timing belt - RH cylinder
head.
13.Top-up engine oil.

+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.
14.Connect battery earth lead.