2001 LAND ROVER FREELANDER radiator

ENGINE - K SERIES KV6
12-3-44 REPAIRS
35.Fit rear beam.

+ FRONT SUSPENSION, REPAIRS,
Rear beam.
36.Fill IRD to correct level with fluid.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) lubrication system -
drain & refill - NAS.
37.Fit exhaust front pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Front pipe - NAS.
38.With assistant depressing the brake pedal,
tighten front hub nuts to 400 Nm.
39.Stake nuts to drive shafts
40.Fit front road wheels, fit and tighten nuts to 115
Nm.
41.Lower vehicle on lift.
42.Connect brake servo vacuum hose to inlet
manifold chamber.
43.Connect coolant hose to underside of
expansion tank and secure with clip.
44.Connect expansion tank hose to inlet manifold
and secure clip.
45.Connect top hose to radiator and secure with
clip. Position hose in bracket.
46.Connect heater feed and return hoses and
secure with clips.
47.Connect throttle inner cable to throttle cam and
secure outer cable in abutment bracket.
48.Connect hose to purge valve.
49.Fit purge hose into clip.
50.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
51.Connect gearbox harness multiplugs and
secure multiplugs in mounting bracket clips.
52.Connect Lucar connector to starter solenoid.
53.Position earth lead to gearbox housing, fit and
tighten bolt to 25 Nm.
54.Position engine harness to 'E' box mounting
bracket and secure with clips.
55.Connect earth header multiplug.
56.Connect multiplug to under bonnet fuse box.
57.Position battery and starter motor lead to under
bonnet fuse box, fit and tighten bolts to 8 Nm.
58.Fit under bonnet fuse box cover.
59.Position 'E' box, secure in retaining clip, fit and
tighten nut to 9 Nm.
60.Fit carrier to 'E' box.
61.Fit air ducting to 'E' box.
62.Fit body harness to 'E' box, secure grommet
and harness clip.
63.Connect 'E' box cooling fan multiplug.
64.Connect multiplug to 'E' box temperature
sensor.
65.Connect multiplug to gearbox ECU.
66.Position engine harness to 'E' box and secure
grommet.67.Fit engine harness clamp and secure with
screws.
68.Connect engine harness multiplug to body
harness multiplug and fit multiplug to 'E' box.
69.Fit heated front screen harness to battery
positive cable and tighten bolt to 15 Nm (11
lbf.ft).
70.Fit engine ECM.

+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - fuel - NAS.
71.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
72.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
73.Connect the battery earth lead.
74.Fill gearbox with fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
75.Fit the engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
76.Untie and close bonnet.

COOLING SYSTEM - K SERIES KV6
ADJUSTMENTS 26-3-1
COOLING SYS TEM - K SER IES KV6 ADJUST ME NTS
Coolant - drain and refill
$% 26.10.01
Drain
1.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Visually check engine and cooling system for
signs of coolant leaks.
WARNING: Since injury such as scalding
could be caused by escaping steam or
coolant, do not remove the filler cap from
the coolant expansion tank while the
system is hot.
3.Examine hoses for signs of cracking, distortion
and security of connections.
4.Remove expansion tank filler cap.
5.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
6.Position container to collect coolant.
7.Remove cylinder block drain plug.
8.Release clip and remove bottom hose from
radiator.
9.Allow cooling system to drain.Refill
1.Flush system with water under low pressure.
Do not use water under high pressure as it
could damage the radiator.
2.Clean cylinder block drain plug and apply
sealant, Part No. STC 50552 to first 3 threads.
3.Fit cylinder block drain plug and tighten to 20
Nm (15 lbf.ft).
4.Fit bottom hose to radiator and secure with clip.
5.Prepare coolant to required concentration.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS, Fluids.
6.Remove bleed screw from heater return hose.
7.Slowly fill the system through the coolant
expansion tank until a steady flow of coolant is
emitted from the bleed hole.
8.Fit and close bleed screw in heater return hose.
9.Continue to fill system through the expansion
tank until coolant reaches to the base of the
expansion tank bleed hose.
10.Fit expansion tank filler cap.
11.Start and run engine at idle speed for 5
minutes.
CAUTION: DO NOT operate air conditioning
12.Switch off engine.
13.Squeeze bottom hose several times to remove
any trapped air.
14.Start engine and run at speeds varying
between idle speed and 3500 rev/min for 7
minutes.
15.Switch off engine and allow to cool.
16.Remove expansion tank filler cap and add
coolant until it reaches the 'MAX' mark on the
expansion tank.
17.Fit expansion tank filler cap.
18.Start and run engine until normal operating
temperature is reached.
CAUTION: The bottom hose must be warm/
hot, this will ensure the thermostat is fully
open.

COOLING SYSTEM - K SERIES KV6
REPAIRS 26-3-3
REPAIRS
Cooling fan and motor
$% 26.25.22
Remove
1.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
2.Remove 3 bolts securing LH cooling fan and
motor assembly to fan cowl. Remove fan and
motor assembly.
Refit
1.Position fan and motor assembly to fan cowl, fit
and tighten bolts to 5 Nm (4 lbf.ft).
2.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
Control unit - radiator cooling fan - 2002
MY On
$% 26.25.43
Remove
1.Disconnect battery earth lead.
2.Release multiplugs from clips and disconnect
2 body harness multiplugs.
3.Disconnect multiplugs from cooling fan motors
and release harness from clips on cooling fan
cowl.
4.Remove screw securing control unit.
5.Release control unit from fan cowl.
Refit
1.Carefully position control unit in cowl and
secure with screw.
2.Connect body harness multiplugs and secure
to cowl.
3.Secure LH and RH harness to retaining clips
and connect multiplugs.
4.Connect battery earth lead.

COOLING SYSTEM - K SERIES KV6
26-3-4 REPAIRS
Radiator assembly
$% 26.40.01
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Drain cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
4. Models without A/C: Remove bumper
valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
5. Models without A/C:Remove 2 bolts securing
PAS fluid cooler to armature.
6. Models without A/C: Remove 4 nuts and 4
bolts securing armature to body and remove
armature.
7. Models with A/C: Remove A/C condenser.

+ AIR CONDITIONING, REPAIRS,
Condenser.
8.Release clips and remove top and bottom
hoses.
CAUTION: Always fit plugs to open
connections to prevent contamination.
9.Release clip and remove expansion hose from
radiator.10. If fitted:Remove 2 bolts and 4 scrivets securing
LH and RH radiator baffles and remove baffles.
11.Remove radiator upper retaining pegs from
bonnet locking platform. Ease top of radiator
forward.
12.Remove 4 bolts securing fan cowl to radiator.
13.Remove 2 cowl retaining clips from radiator.
M26 0947

COOLING SYSTEM - K SERIES KV6
REPAIRS 26-3-5
14.Release radiator from lower mountings and
remove from vehicle.
15.Remove radiator upper mounting extension
brackets.
16.Remove 4 rubber mountings from radiator.Refit
1.Fit mounting rubbers to radiator.
2.Fit upper support brackets to radiator.
3.Position fan cowl to radiator, fit and tighten
bolts to 5 Nm (4 lbf.ft).
4.Secure fan cowl to radiator with clips.
5.Fit radiator and engage lower mountings in
chassis.
6.Fit radiator upper mountings to bonnet locking
platform.
7. If fitted:Position LH and RH radiator baffles,
secure with scrivets, fit and tighten top bolts to
5 Nm (4 lbf.ft).
8.Connect expansion tank hose and secure with
clip.
9.Connect bottom and top hoses to radiator
secure with clips.
10. Models with A/C: Fit A/C condenser.

+ AIR CONDITIONING, REPAIRS,
Condenser.
11. Models without A/C: Position armature, fit and
tighten 4 nuts and bolts securing armature to
body.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
12. Models without A/C: Align PAS fluid cooler
and tighten bolts to 8 Nm (6 lbf.ft).
13. Models without A/C: Fit bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
14.Refill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
15.Fit acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
16.Connect battery earth lead.
M26 0946

PANEL REPAIRS
WELDING PROCEDURES 77-2-15
WE LDING PROCEDURE S
ECU locations (3 door model shown, 5
door model similar)
1Central control unit (on forward side of
passenger compartment fusebox, behind
driver's glove box)
2RF Receiver (on top of instrument pack)
3Immobiliser ECU (rear of fascia)
4DCU (SRS on transmission tunnel below
heater)
5EAT ECU (inside Environmental 'E' box)
6ECM (inside 'E' box)
7Fuel Burning Heater (behind wheelarch liner)
'Diesel only'8Cooling Fan Ecu (rear of radiator housing) all
models except 1.8
9ABS ECU (RH side front of engine
compartment)
10Folding door mirror ECU (on transmission
tunnel under centre console)
11Window lift ECU (on driver `A` post)
12Cruise Control Interface ECU (under R/H seat)
13Cruise control ECU (under R/H seat)

PANEL REPAIRS
REPAIRS 77-2-25
REPAIRS
Front bulkhead assembly
In this procedure, the crossmember gusset plates
are replaced in conjunction with the front bulkhead
assembly.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
5.Remove front bumper armature.
6.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
7.Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
8.Remove LH and RH headlamps.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
9.Release wiring to headlamps and position
aside.
10.Remove LH and RH engine bay shields.
11.Remove bumper valance LH and RH
attachment brackets.
12.Remove battery.

+ CHARGING AND STARTING,
REPAIRS, Battery.
13.Remove air intake hose.
14.Remove horn.

+ SECURITY, REPAIRS, Horn.
15.Remove windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
16.Remove bonnet lock.
17.Support bonnet in open position.
18.Remove bonnet stay. Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.

PANEL REPAIRS
77-2-26 REPAIRS
Refit
1.Fit bonnet stay.
2.Fit bonnet lock.
3.Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
4.Fit horn.

+ SECURITY, REPAIRS, Horn.
5.Fit air intake hose.
6.Fit battery. Do not connect earth lead.

+ CHARGING AND STARTING,
REPAIRS, Battery.
7.Fit bumper valance LH and RH attachment
brackets.
8.Fit LH and RH engine bay shields.
9.Fit LH and RH headlamps.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY. Secure headlamps
wiring.
10.Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
11.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
12.Fit front bumper armature.
13.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
14.Connect all ECUs.
15.Connect alternator.
16.Connect battery earth lead.