2001 LAND ROVER FREELANDER coolant

TORQUE WRENCH SETTINGS
06-2
Engine – Td4
TORQUE DESCRIPTION METRIC IMPERIAL
Acoustic cover to engine 8 Nm 6 lbf.ft
Ancillary drive belt jockey pulley Allen bolt
*24 Nm 18 lbf.ft
Ancillary drive belt tensioner arm nut 10 Nm 7.5 lbf.ft
Big end bearing cap bolts:
⇒ Stage 15 Nm 3.5 lbf.ft
⇒ Stage 225 Nm 18 lbf.ft
⇒ Stage 3+70°+70°
Camshaft bearing cap bolts
† 10 Nm 7.5 lbf.ft
Camshaft cover bolts
† 10 Nm 7.5 lbf.ft
Camshaft sprocket retaining screw:
⇒ Stage 120 Nm 15 lbf.ft
⇒ Stage 2+35°+35°
Chain lubrication jet bolt 10 Nm 7.5 lbf.ft
Coolant rail to exhaust manifold bolts 20 Nm 15 lbf.ft
Coolant rail to exhaust manifold bolts 8 Nm 6 lbf.ft
Crankshaft pulley:
⇒ Stage 1100 Nm 74 lbf.ft
⇒ Stage 2+60 °+60 °
⇒ Stage 3+60 °+60 °
⇒ Stage 4+30 °+30 °
Crankshaft rear oil seal housing:
⇒ M6 bolts10 Nm 7.5 lbf.ft
⇒ M8 bolts22 Nm 16 lbf.ft
Cylinder block reinforcing plate 22 Nm 16 lbf.ft
Cylinder head bolts: (Stages 1 to 5 relate to bolts 1 to 11. Stage 6 is for bolt 12 only.)
⇒ Stage 1
†80 Nm 59 lbf.ft
⇒ Stage 2 - loosen all bolts
†-1/2 turn -1/2 turn
⇒ Stage 3
†50 Nm 37 lbf.ft
⇒ Stage 4
†+90°+90°
⇒ Stage 5
†+90°+90°
⇒ Stage 6 – tighten 41 mm bolt in position 12 110 Nm 81 lbf.ft
Cylinder head to timing cover Allen screws 15 Nm 11 lbf.ft
Dipstick tube to oil filter housing bolt 10 Nm 7.5 lbf.ft
Drive plate to crankshaft bolts
† 115 Nm 85 lbf.ft
EGR cooler to cylinder head and lifting bracket bolts 25 Nm 18 lbf.ft
Engine breather pipe to air cleaner housing bolt 10 Nm 7.5 lbf.ft
Engine lifting eye bolts 20 Nm 15 lbf.ft
Engine mounting bracket assembly to engine bolts 100 Nm 74 lbf.ft
Engine mounting bracket to hydramount nut 85 Nm 63 lbf.ft
Engine lower steady bracket bolts:
⇒ M1045 Nm 33 lbf.ft
⇒ M1250 Nm 37 lbf.ft
Engine steady mounting bolt 100 Nm 74 lbf.ft
Exhaust manifold to cylinder head nuts 24 Nm 18 lbf.ft
Flywheel to crankshaft bolts
† 115 Nm 85 lbf.ft
Fuel pipe bracket to oil filter housing bolt 10 Nm 7.5 lbf.ft
Fuel pipe union nuts 30 Nm 22 lbf.ft
Fuel pump drive chain lower guide Allen bolt 24 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-3
† Tighten in sequence
* Fit new bolt
Fuel pump sprocket retaining nut 65 Nm 48 lbf.ft
Fuel rail Allen screws 24 Nm 18 lbf.ft
Fuel rail to coolant rail bolts 10 Nm 7.5 lbf.ft
Fuel rail to support bracket bolts 10 Nm 7.5 lbf.ft
Glow plugs18 Nm 13 lbf.ft
Heatshield to coolant rail Allen screws 8 Nm 6 lbf.ft
Hose adaptor to cylinder head bolts 8 Nm 6 lbf.ft
LH engine mounting to gearbox bracket through bolt 100 Nm 74 lbf.ft
LH engine mounting to body 45 Nm 33 lbf.ft
Lower coolant rail support bracket bolts 15 Nm 11 lbf.ft
Main bearing cap bolts:
⇒ 1st. Stage
† 20 Nm 15 lbf.ft
⇒ 2nd Stage
† +70°+70°
Oil cooler to oil filter housing bolts 22 Nm 16 lbf.ft
Oil feed guide rail bolts 10 Nm 7.5 lbf.ft
Oil filter cap25 Nm 18 lbf.ft
Oil filter housing bolts 25 Nm 18 lbf.ft
Oil pick-up strainer to oil pump bolts 10 Nm 7.5 lbf.ft
Oil pressure switch 38 Nm 28 lbf.ft
Oil pump drive gear to oil pump drive shaft Torx bolt 25 Nm 18 lbf.ft
Oil pump to cylinder block 25 Nm 18 lbf.ft
PAS pipe clip to engine lifting eye bolt 10 Nm 7.5 lbf.ft
Sump: †
⇒ M6 bolts10 Nm 7.5 lbf.ft
⇒ M8 bolts28 Nm 21 lbf.ft
Sump drain plug28 Nm 21 lbf.ft
Sump plate bolts10 Nm 7.5 lbf.ft
Timing chain support guides 20 Nm 15 lbf.ft
Timing chain tensioner access plug 30 Nm 22 lbf.ft
Timing chain tensioner bolt 10 Nm 7.5 lbf.ft
Timing cover bolts
† 15 Nm 11 lbf.ft
Turbocharger to exhaust manifold bolts 45 Nm 33 lbf.ft
Turbocharger outlet pipe fixing bolts:
⇒ 6mm10 Nm 7.5 lbf.ft
⇒ 8mm25 Nm 18 lbf.ft
Vacuum pump bolts 22 Nm 16 lbf.ft

TORQUE WRENCH SETTINGS
06-4
Engine – K1.8
TORQUE DESCRIPTION METRIC IMPERIAL
Big end bearing cap dowel bolts:
⇒ Stage 120 Nm 15 lbf.ft
⇒ Stage 2+45°+45°
Bearing ladder to cylinder block bolts:
⇒ Stage 1
†++5 Nm 3.5 lbf.ft
⇒ Stage 2
† ++30 Nm 22 lbf.ft
Camshaft carrier to cylinder head bolts
†++10 Nm 7.5 lbf.ft
Camshaft cover to carrier bolts
†8 Nm 6 lbf.ft
Camshaft gear bolt 65 Nm 48 lbf.ft
Camshaft rear oil seal cover plate bolts:
⇒ Exhaust25 Nm 18 lbf.ft
⇒ Inlet6 Nm 4.5 lbf.ft
Camshaft sensor bolt 8 Nm 6 lbf.ft
Camshaft timing belt lower front cover bolts 9 Nm 7 lbf.ft
Camshaft drive belt upper front cover bolts 5 Nm 3.5 lbf.ft
Camshaft timing belt rear cover bolts 9 Nm 7 lbf.ft
Camshaft timing belt tensioner bolt
* 25 Nm 18 lbf.ft
Camshaft upper cover to rear cover bolts 5 Nm 3.5 lbf.ft
Coolant outlet elbow to cylinder head bolts 9 Nm 7 lbf.ft
Crankshaft pulley bolt 205 Nm 151 lbf.ft
Cylinder head bolts
⇒ Stage 1
†20 Nm 15 lbf.ft
⇒ Stage 2
†+180 °+180 °
⇒ Stage 3
†+180 °+180 °
Dipstick tube to cylinder block 10 Nm 7.5 lbf.ft
Dipstick tube bracket and thermostat housing to cylinder block bolt 10 Nm 7.5 lbf.ft
Engine earth lead to body nut 9 Nm 7 lbf.ft
Engine harness to oil pump housing bolts 10 Nm 7.5 lbf.ft
Engine LH gearbox mounting bracket through bolt 80 Nm 59 lbf.ft
Engine LH mounting bracket to body bolts 45 Nm 33 lbf.ft
Engine lower steady to sump mounting bracket bolt 80 Nm 59 lbf.ft
Engine lower steady bracket to sump bolts 100 Nm 74 lbf.ft
Engine lower steady to subframe bolt 80 Nm 59 lbf.ft
Engine steady to LH mounting bolt 25 Nm 18 lbf.ft
Engine steady (lower) to rear beam bolt 80 Nm 59 lbf.ft
Engine steady (lower) to sump mounting bracket bolt 80 Nm 59 lbf.ft
Engine steady (upper RH) to body bolt 80 Nm 59 lbf.ft
Engine steady (upper RH) to top arm bolt 80 Nm 59 lbf.ft
Engine to gearbox top and front cover plate bolts and nuts 80 Nm 59 lbf.ft
Flywheel to crankshaft bolts
†*80 Nm 59 lbf.ft
Front cover plate to gearbox M6 bolt 9 Nm 7 lbf.ft
Ignition coils to camshaft cover bolts 8 Nm 6 lbf.ft
Oil pick-up strainer bolt 12 Nm 9 lbf.ft
Oil pick-up strainer support bracket to oil rail bolt 12 Nm 9 lbf.ft
Oil pressure switch
+17 Nm 12.5 lbf.ft
Oil pressure relief valve plug
+25 Nm 18 lbf.ft
Oil pump to cylinder block bolts
†*10 Nm 7.5 lbf.ft
Oil rail to bearing ladder nuts
++9 Nm 7 lbf.ft

TORQUE WRENCH SETTINGS
06-8
Emission Control
TORQUE DESCRIPTION METRIC IMPERIAL
Depression limiter valve and filter assembly Allen screws 8 Nm 6 lbf.ft
EGR cooler to mounting bolts 25 Nm 18 lbf.ft
EGR valve Allen screws 10 Nm 7.5 lbf.ft
EGR solenoid valve bolts 10 Nm 7.5 lbf.ft
EGR pipe to lifting bracket and cylinder head bolts 25 Nm 18 lbf.ft
Fuel rails to support bracket bolt 10 Nm 7.5 lbf.ft
Turbocharger outlet pipe to support bracket bolt 10 Nm 7.5 lbf.ft
Turbocharger pipe to coolant rail bolts 25 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-9
Engine Management System – EDC
TORQUE DESCRIPTION METRIC IMPERIAL
Camshaft position (CMP) sensor Torx screw 8 Nm 6 lbf.ft
Crankshaft position (CKP) sensor Allen screw 8 Nm 6 lbf.ft
'E' box cover Allen screws 2 Nm 1.5 lbf.ft
Engine coolant temperature sensor (ECT) 15 Nm 11 lbf.ft
Engine breather pipe to air cleaner housing bolt 6 Nm 4.4 lbf.ft
Mass air flow / inlet air temperature MAF/IAT sensor to air cleaner housing 6 Nm 4.4 lbf.ft
Throttle pedal to stud nuts 25 Nm 18 lbf.ft
Throttle Position (TP) sensor nuts and bolts 10 Nm 7 lbf.ft
TP sensor release lever nut 10 Nm 7 lbf.ft

TORQUE WRENCH SETTINGS
06-10
Engine Management System – MEMS
+ Apply sealant, Part No. STC 50552 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Camshaft position (CMP) sensor bolt 8 Nm 6 lbf.ft
Crankshaft position sensor (CKP) to housing bolt 8 Nm 6 lbf.ft
'E' box retaining clip nut 9 Nm 7 lbf.ft
Engine coolant temperature (ECT) sensor to housing bolt
*15 Nm 11 lbf.ft
Fuel cut-off (inertia) switch nuts 2 Nm 1.5 lbf.ft
Idle air control (IAC) valve to manifold Torx screws 1.5 Nm 1.1 lbf.ft
Ignition coil and ht lead cover bolts 10 Nm 7.5 lbf.ft
Ignition coil mounting bolts 8 Nm 6 lbf.ft
Spark plugs to cylinder head 27 Nm 20 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 7 Nm 5 lbf.ft
Throttle actuator support bracket to throttle body Torx screws
(vehicles with cruise control only)9 Nm 7 lbf.ft
Throttle position sensor to housing Torx screws 1.5 Nm 1.1 lbf.ft

TORQUE WRENCH SETTINGS
06-11
Engine Management System – Siemens
TORQUE DESCRIPTION METRIC IMPERIAL
Camshaft position (CMP) sensor 8 Nm 6 lbf.ft
CMP sensor mounting bracket bolt 8 Nm 6 lbf.ft
Crankshaft position (CKP) sensor bolt 9 Nm 6.5 lbf.ft
Engine Coolant temperature (ECT) sensor 17 Nm 12.5 lbf.ft
'E' box cover Allen screws 2 Nm 1.5 lbf.ft
'E' box mounting nut 9 Nm 7 lbf.ft
Plug top coils to LH inlet manifold nut and bolt 9 Nm 6.5 lbf.ft
Plug top coils to RH camshaft cover bolts 9 Nm 6.5 lbf.ft
Spark plugs25 Nm 18 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 7 Nm 5 lbf.ft
Throttle pedal assembly to bulkhead nuts 25 Nm 18 lbf.ft
Throttle position (TP) sensor screws 1.5 Nm 1.1 lbf.ft

TORQUE WRENCH SETTINGS
06-14
Cooling System – Td4
Cooling System – K1.8
Cooling System – KV6
†Tighten in sequence.
+ Apply sealant, Part No. STC 50552 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant hose adaptor to cylinder head bolts 8 Nm 6 lbf.ft
Coolant rail (lower) to sump bolts 10 Nm 7.5 lbf.ft
Coolant rail to cylinder head bolt 20 Nm 15 lbf.ft
Coolant rail to exhaust manifold bolt 20 Nm 15 lbf.ft
Coolant pump to cylinder block bolts 10 Nm 7.5 lbf.ft
Fan and motor assembly to fan cowl bolts 5 Nm 4 lbf.ft
Fan cowl to radiator bolts 5 Nm 4 lbf.ft
Fuel cooler to mounting nuts 10 Nm 7.5 lbf.ft
Fuel rail to coolant rail bolt 10 Nm 7.5 lbf.ft
Heatshield to coolant rail Allen screws 8 Nm 6 lbf.ft
Thermostat housing to coolant pump bolts 8 Nm 6 lbf.ft
Upper coolant rail to thermostat housing bolt 8 Nm 6 lbf.ft
TORQUE DESCRIPTION METRIC IMPERIAL
Condenser to radiator bolts 3 Nm 2.2 lbf.ft
Cooling fan control unit mounting bolt 5 Nm 4 lbf.ft
Cooling fan cowl to radiator 5 Nm 4 lbf.ft
Cooling fan and motor assembly to cowl bolts 5 Nm 4 lbf.ft
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant pump to cylinder block bolts
†9 Nm 6.5 lbf.ft
Cooling fan and motor assembly to fan cowl bolts 5 Nm 3.7 lbf.ft
Cooling fan cowl to radiator bolts 5 Nm 3.7 lbf.ft
Cylinder block drain plug
+20 Nm 15 lbf.ft
Injector protection cover to RH fuel rail and inlet manifold bolts 9 Nm 6.5 lbf.ft
Radiator baffle bolts 5 Nm 3.7 lbf.ft
Thermostat housing flange / coolant elbow bolt 18 Nm 13 lbf.ft