2001 LAND ROVER FREELANDER wheel

BRAKES
70-26 REPAIRS
7.Release 2 grommets from wing valance and
damper brackets
8.Release harness from brake hose clips.
9.Remove bolt securing ABS sensor to hub, if
fitted.
10.Release ABS sensor from hub.
11.Remove ABS sensor and harness.
12.Remove bush from front hub.Refit
1.Clean ABS sensors and mating faces.
2.Fit new bush to front hub.
3.Apply anti-seize grease to sensor.
4.Fit sensor to hub, ensure sensor is fully seated
in hub.
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
pole wheel teeth.
5.Fit and tighten bolt securing ABS sensor to hub,
if fitted.
6.Secure harness grommets to brackets.
7.Pass sensor harness through wing valance and
secure grommet.
8.Ensure 'O' ring is in place and connect sensor
multiplug to body harness.
9.Secure multiplug in body clip.
10.Secure harness to brake hose clip.
11.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
12.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
13.Remove stand and lower vehicle.
14.To ensure correct operation, the ABS system
MUST be tested using TestBook/T4.

BRAKES
REPAIRS 70-27
Sensor & harness - front wheel - LH
$% 70.65.30
Remove
1.Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
5.Locate ABS sensor harness on inner wing.
6.Release ABS sensor multiplug from body clip
and disconnect multiplug.
7.Release grommet from wing valance and pull
harness through.8.Release 2 grommets from wing valance and
damper brackets
9.Release harness from brake hose clips.
10.Remove bolt securing ABS sensor to hub, if
fitted.
11.Release ABS sensor from hub.
12.Remove ABS sensor and harness.
13.Remove bush from front hub.

BRAKES
70-28 REPAIRS
Refit
1.Clean ABS sensors and mating faces.
2.Fit new bush to front hub.
3.Apply anti-seize grease to sensor.
4.Fit sensor to hub, ensure sensor is fully seated
in hub.
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
pole wheel teeth.
5.Fit bolt securing ABS sensor to hub, if fitted.
6.Secure harness grommets to brackets.
7.Pass sensor harness through wing valance and
secure grommet.
8.Ensure 'O' ring is in place and connect sensor
multiplug to body harness.
9.Secure multiplug in body clip.
10.Secure harness to brake hose clip.
11.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
12.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
13.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
14.Remove stand and lower vehicle.
15.To ensure correct operation, the ABS system
MUST be tested using TestBook/T4.

BRAKES
REPAIRS 70-29
Sensor & harness - rear wheel
$% 70.65.31
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Release ABS sensor multiplug from body clip
and disconnect multiplug.
4.Release ABS sensor harness from 3 grommets
on suspension and body brackets.
5.Release harness from clip on rear brake hose.6.Remove bolt securing ABS sensor to hub, if
fitted.
7.Release sensor from rear hub and remove
sensor and harness.
8.Remove bush from rear hub.
Refit
1.Clean sensor and rear hub mating faces.
2.Fit new bush to rear hub.
3.Apply anti-seize grease to sensor.
4.Fit sensor to hub, ensure sensor is fully seated
in hub.
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
pole wheel teeth.
5.Fit bolt securing ABS sensor to hub, if fitted.
6.Ensure 'O' ring is in place and connect sensor
multiplug to body harness.
7.Secure multiplug in body clip.
8.Secure harness grommets to brackets.
9.Secure harness to brake hose clip.
10.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
11.Remove stands and lower vehicle.
12.To ensure correct operation, the ABS system
MUST be tested using TestBook/T4.

RESTRAINT SYSTEMS
REPAIRS 75-13
Air bag - steering wheel
$% 76.74.01
Remove
WARNING: It is imperative that before any
work is undertaken on the SRS system the
appropriate information is read thoroughly.
WARNING: When removing, testing or
installing an airbag module, do not lean
directly over it.
1.Make the SRS system safe.

+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove 2 Torx bolts securing airbag module to
steering wheel.
3.Release airbag module from steering wheel.
CAUTION: Do not allow the airbag module
to hang by the airbag harness.
4.Disconnect SRS connector from air bag
module.
5.Remove airbag module.
WARNING: Store the airbag module with the
deployment side uppermost. If it is stored
deployment side down, accidental
deployment will propel the airbag module
with enough force to cause serious injury.Refit
1.Position airbag module and fit connector with
harness pointing upwards.
NOTE: If the airbag module is to be replaced,
the bar code of the new module must be
recorded.
2.Fit airbag module to steering wheel and tighten
Torx bolts to 9 Nm (7 lbf.ft).
3.Connect battery leads, earth lead last.

RESTRAINT SYSTEMS
REPAIRS 75-19
Rotary coupler - (SRS) air bag system
$% 76.74.20
Remove
WARNING: It is imperative that before any
work is undertaken on the SRS system the
appropriate information is read thoroughly.
1.Make the SRS system safe.

+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
CAUTION: Before disconnecting any part of
the steering linkage, ensure the road wheels
are positioned straight ahead and the
steering wheel is prevented from turning.
Unrestricted turning of the steering wheel
will damage the SRS rotary coupler.
2.Remove steering wheel.

+ STEERING, REPAIRS, Steering
wheel.
CAUTION: Use adhesive tape to prevent
rotation of the rotary coupler once the
steering wheel is removed.
3.Remove steering column nacelle.

+ STEERING, REPAIRS, Nacelle -
column.
4.Disconnect 2 multiplugs from rotary coupler.
5.Remove 4 screws and remove rotary coupler.
CAUTION: Do not dismantle the rotary
coupler, it has no serviceable parts and
must be replaced as a complete assembly.Refit
1.Ensure the rotary coupler is installed in its
centred position. To obtain centre position,
rotate coupler gently clockwise and
anticlockwise until the white segment appears
on the indicator wheel.
CAUTION: Ensure front road wheels are in
the straight ahead position.
2.Fit rotary coupler and secure with screws.
3.Connect multiplugs to rotary coupler.
4.Fit steering column nacelle.

+ STEERING, REPAIRS, Nacelle -
column.
5.Fit steering wheel.

+ STEERING, REPAIRS, Steering
wheel.
6.Connect battery leads, earth lead last.

RESTRAINT SYSTEMS
75-20 REPAIRS
Airbag module - steering wheel -
deployment - off vehicle
$% 76.74.16
These guidelines are written to aid authorised
personnel to carry out the safe disposal of airbag
modules when removed from the vehicle.
Deploy
WARNING: It is imperative that before any
work is undertaken on the SRS system, the
appropriate information is read thoroughly.
1.Make the SRS system safe.

+ GENERAL INFORMATION, SRS
component manual deployment.
2.Remove airbag module from steering wheel.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
3.Check condition of deployment tool LRT-86-
003 and associated flyleads.
4.Position toolLRT-86–007–02 in vice, ensuring
that vice jaws grip tool above bottom flange to
prevent possibility of tool being forced upwards
from vice. Tighten vice.
5.Secure airbag module to tool LRT-86–007–02
using both fixings LRT-86–007–05.
6.Ensure airbag module mounting brackets are
secure.
WARNING: Ensure the deployment tool is
not connected to the battery.7.Connect deployment tool flylead LRT-86–003–
08 to driver airbag module.
8.Connect deployment tool flylead LRT-86–003–
08 to deployment tool LRT-86–003.
9.Connect tool LRT-86–003 to battery.
WARNING: Ensure all personnel are at least
15 metres (50 ft) away from the airbag
module.

RESTRAINT SYSTEMS
REPAIRS 75-21
10.Press deployment tool operating button to
deploy airbag module.
WARNING: During deployment parts of the
airbag module become hot enough to burn
you. Wait 30 minutes after deployment
before touching the airbag module.
11.Disconnect deployment tool flylead LRT-86–
003–08 from driver airbag module.
12.Using gloves and face mask, remove airbag
module from tool LRT-86–007–02, place airbag
module in plastic bag and seal bag.
13.Wipe down tool with damp cloth.
14.Transport deployed airbag module to
designated area for incineration.
NOTE: Do not transport deployed SRS
components in the vehicle passenger
compartment.
15.DO NOT re-use or salvage any parts of the
SRS system including steering wheel or
steering column.
Airbag module - steering wheel -
deployment - in-vehicle
$% 76.74.15
These guidelines are written to aid authorised
personnel to carry out the safe deployment and
disposal of airbag modules when still fitted to the
vehicle.
Deploy
WARNING: It is imperative that before any
work is undertaken on the SRS system, the
appropriate information is read thoroughly.
1.Make the SRS system safe.

+ GENERAL INFORMATION, SRS
component manual deployment.
2.Check condition of deployment tool LRT-86–
003and associated flyleads.
3.Remove steering column nacelle.
4.Disconnect SRS harness connector from back
of rotary coupler.
WARNING: Ensure airbag module is secure
within steering wheel.
WARNING: Ensure the deployment tool is
not connected to the battery.