2001 LAND ROVER FREELANDER fuel

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-39
Injectors - set - K1.8
$% 19.60.12
Remove
1.Disconnect battery earth lead.
2.Release clip and disconnect vacuum pipe from
fuel pressure regulator.
3.Remove engine oil dipstick.
4.Position absorbent cloth beneath fuel rail.
5.Release fuel feed hose from fuel rail.
CAUTION: Always fit plugs to open
connections to prevent contamination.6.Remove 2 bolts securing fuel rail to inlet
manifold.
7.Release fuel rail and injectors from inlet
manifold.
8.Release and remove injector spacer.
9.Disconnect multiplug from injectors.
10.Remove the fuel rail complete with injectors.
11.Release spring clips securing injectors to fuel
rail and remove fuel injectors.
12.Remove and discard 2 'O' rings from each
injector.
13.Fit protective caps to each end of injectors.

FUEL DELIVERY SYSTEM - PETROL
19-2-40 REPAIRS
Refit
1.Remove protective caps from each injector.
2.Clean injectors and recesses in fuel rail and
inlet manifold.
3.Lubricate new 'O' ring with castor oil and fit to
injector.
4.Fit injectors to fuel rail and secure with spring
clips.
5.Position fuel rail assembly and connect injector
multiplugs.
6.Fit injector spacer.
7.Push each injector into inlet manifold.
8.Fit bolts securing fuel rail to inlet manifold and
tighten to 8 Nm ( 6 lbf.ft).
9.Connect fuel feed hose to fuel rail.
10.Fit engine oil dipstick.
11.Connect vacuum pipe to fuel pressure regulator
and secure with clip.
12.Connect battery earth lead.
Actuator unit - cruise control - KV6 - non
NAS
$% 19.75.05
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Disconnect vacuum hose from actuator.
4.Remove nut securing actuator to mounting
bracket.
5.Release operating rod from throttle cam and
remove actuator.
Refit
1.Position actuator and connect operating rod to
throttle cam.
2.Position actuator into mounting bracket, fit and
tighten nut.
3.Connect vacuum hose to actuator.
4.Check pull rod to retainer clearance, with lever
fully returned, pull rod should just be held by
retainer.
5.Release retainer by turning anti-clockwise,
eliminate clearance then rotate retainer half
turn clockwise. Check pull rod is just held and
rotate retainer a further quarter turn clockwise
to lock.
6.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
7.Connect battery earth lead.

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-41
Vacuum pump - cruise control - KV6 -
non NAS
$% 19.75.06
Remove
1.Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
2.Release 3 rubber mountings securing vacuum
pump to battery carrier and remove vacuum
pump.
3.Remove 3 rubber mountings from vacuum
pump.
Refit
1.Fit rubber mountings to vacuum pump.
2.Position vacuum pump to battery carrier and
secure with rubber mountings.
3.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
Switch - cruise control - KV6 - up to 04MY
$% 19.75.30
Remove
1.Remove radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.
2.Remove selector knobs from heater controls.
3.Remove 2 screws securing heater control
finisher to heater controls and remove finisher.
4.Release cruise control switch, disconnect
multiplug and remove switch.
Refit
1.Position cruise control switch, connect
multiplug and secure switch.
2.Fit heater control finisher to heater controls and
secure with screws.
3.Fit heater control knobs.
4.Fit radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.

FUEL DELIVERY SYSTEM - PETROL
19-2-42 REPAIRS
Switch - engagement (on/off) - from
04MY
$% 19.75.30
Remove
1.Release 2 clips and remove fascia mounted
switch cover.
2.Remove 2 screws securing switch carrier to
fascia.
3.Release switch carrier from fascia and
disconnect switch multiplug.
4.Remove switch assembly from carrier.
Refit
1.Fit switch to carrier.
2.Connect multiplug to switch.
3.Secure switch carrier to fascia with screws.
4.Fit and secure switch cover.
Switch - multi-purpose
$% 19.75.33
Remove
1.Remove airbag module from steering wheel.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
2.Release cruise control switch leads from clip
and disconnect multiplug.
3.Remove 2 screws securing cruise control
switch and remove switch.
Refit
1.Fit cruise control switch and secure with
screws.
2.Connect switch multiplug and fit leads in clip.
3.Fit drivers airbag.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
M19 3672

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-43
ECU - cruise control - KV6
$% 19.75.49
Remove
1.Slide RH front seat fully rearwards.
2.Remove 2 screws securing ECU cover.
3.Remove cover.
4.Release interface ECU from bracket and move
aside.
5.Remove 2 screws securing cruise control ECU.
6.Disconnect multiplug from ECU and remove
ECU.
Refit
1.Connect multiplug to ECU.
2.Position ECU and tighten screws.
3.Secure interface ECU to bracket.
4.Fit ECU cover and secure with screws.
5.Position seat to mid position.
Interface ECU - cruise control - KV6
$% 19.75.55
Remove
1.Slide RH front seat fully rearwards.
2.Remove 2 screws securing ECU cover.
3.Remove cover.
4.Release interface ECU from bracket,
disconnect multiplug and remove ECU.
Refit
1.Position ECU, connect multiplug and secure
ECU to bracket.
2.Fit ECU cover and secure with screws.
3.Position seat to mid position.

COOLING SYSTEM - K SERIES KV6
26-3-6 REPAIRS
Thermostat
$% 26.45.01
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
3.Remove inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
4.Remove 2 bolts securing RH fuel rail to inlet
manifold. Remove injector protection cover if
fitted.
5.Release 2 clips securing engine harness to rear
engine lifting bracket and bracket on RH inlet
manifold.
6.Release clip and disconnect bottom hose from
thermostat housing.
7.Loosen clip and disconnect heater hose from
thermostat housing.8.Release clip and disconnect top hose from
coolant elbow.
9.Remove bolt securing thermostat housing and
coolant elbow to cylinder block.
10.Remove coolant elbow from cylinder block.
11.Remove thermostat housing and coolant pipe
from cylinder block.
12.Release clip and remove coolant pipe from
thermostat housing.
13.Remove and discard 4 'O' rings from
thermostat housing, coolant elbow and coolant
pipe.
Refit
1.Lubricate new 'O' rings with rubber grease and
fit to sealing grooves in thermostat housing,
coolant elbow and coolant pipe.
2.Fit coolant pipe into thermostat housing, ensure
clip connectors are uppermost.
3.Position thermostat housing and coolant pipe
above cylinder block, engage coolant pipe in
cylinder block and press thermostat housing
firmly into position. Ensure mounting flange on
thermostat housing is aligned to bolt hole in
cylinder block.
4.Fit coolant elbow into cylinder block, press
firmly into place. Ensure mounting flange is
aligned correctly to thermostat housing flange.
5.Fit bolt to coolant elbow and thermostat
housing flanges. Tighten bolt to 18 Nm (13
lbf.ft).
6.Connect top hose to coolant elbow and secure
with clip.
7.Connect heater and bottom hoses to
thermostat housing, secure with clips.
8.Position and secure engine harness to brackets
with clips.
9.If fitted, position injector protection cover to RH
fuel rail, fit and tighten bolts to 9 Nm (7 lbf.ft).
10.Fit inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
11.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
12.Connect battery earth lead.

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
30-3-8 REPAIRS
Gasket - inlet manifold - LH
$% 30.15.08
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
3.Remove fuel rail.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - Non
NAS.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - NAS.
4.Depress locking collar and release breather
hose from LH inlet manifold.
5.Release clip and disconnect coolant hose from
LH inlet manifold.
6.Progressively loosen and remove 7 bolts
securing LH inlet manifold to cylinder head.
7.Remove inlet manifold and discard gasket.Refit
1.Clean inlet manifold and cylinder head mating
faces.
2.Fit new inlet manifold gasket to cylinder head,
position inlet manifold, fit and tighten bolts to 25
Nm (18 lbf.ft).
3.Connect breather hose to LH inlet manifold.
4.Connect coolant hose to inlet manifold and
secure clip.
5.Fit fuel rail.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - Non
NAS.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - NAS.
6.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
7.Connect battery earth lead.

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
REPAIRS 30-3-13
13.Remove 4 nuts securing manifold and remove
exhaust manifold.
14.Remove and discard manifold and down pipe
gaskets.
Refit
1.Clean exhaust manifold and mating faces.
2.Using new gaskets, fit exhaust manifold and
tighten nuts to cylinder head to 45 Nm (33 lbf.ft)
and nuts to front pipe to 50 Nm (37 lbf.ft).
3.Connect H02S multiplugs, secure multiplugs to
brackets and harness to clips.
4.Clean compressor and mounting bracket
mating faces.
5.Fit compressor heat shield.
6.Position compressor to mounting and align
heat shield. Fit and tighten bolts to 25 Nm (18
lbf.ft).
7.Using a 3/8" square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
8.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
9.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
10.Connect battery earth lead.
Seals - inlet manifold chamber - up to
03MY
$% 30.15.37
Remove
1.Disconnect battery earth lead.
2.Remove vacuum enhancer.

+ BRAKES, REPAIRS, Vacuum -
enhancer - KV6.
3.Position absorbent cloth around fuel feed pipe
connection to collect spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
4.Pull back rubber sleeve on fuel pipe connector,
release connector and disconnect fuel pipe
from fuel rail pipe.
CAUTION: Always fit plugs to open
connections to prevent contamination.