2001 LAND ROVER FREELANDER exhaust

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
OVERHAUL 30-3-25
OVERHAUL
Seals - manifold chamber - up to 03MY
$% 30.15.37.01
Remove
1.Disconnect multiplug from purge control valve.
2.Disconnect small vacuum hose from purge
control valve.
3.Depress locking collar and release vacuum
hose from IACV housing .
4.Disconnect multiplug from IACV.
5.Disconnect multiplug from TP sensor.
6.Depress locking collars and release vacuum/
breather hose from purge control valve and LH
camshaft cover. Release clip securing hose to
'T' piece and remove hose.
7.Depress locking collars and release vacuum/
breather hoses from throttle body, LH and RH
camshaft cover and remove hose.8.Disconnect multiplugs from VIS motors.
9.Remove 2 screws securing engine harness
brackets to inlet manifold chamber and position
harness aside.
10.Remove 2 bolts securing inlet manifold
chamber rear support brackets to RH camshaft
cover.

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
30-3-26 OVERHAUL
11.Release 2 clips securing RH plug top coil
harness to inlet manifold camber rear support
brackets.
12.Remove 4 bolts securing inlet manifold
chamber to LH inlet manifold.
13.Release and raise inlet manifold chamber from
inlet manifolds.
14.Remove inlet manifold chamber.15.Remove and discard seals from inlet manifold
chamber and 'O' rings from RH inlet manifold.
Refit
1.Clean seal faces on inlet manifold chamber and
inlet manifolds.
2.Fit new 'O' rings to RH inlet manifold and new
seals to manifold chamber.
3.Position inlet manifold chamber, secure RH coil
harness clips in inlet manifold chamber support
brackets.
4.Align inlet manifold chamber to inlet manifolds,
fit and tighten bolts to 18 Nm (13 lbf.ft).
5.Align inlet manifold chamber support brackets
to RH camshaft cover, fit and tighten bolts to 10
Nm (7.5 lbf.ft).
6.Position engine harness brackets to inlet
manifold chamber, fit and tighten screws.
7.Connect multiplugs to VIS motors.
8.Connect vacuum/breather hoses to LH and RH
camshaft covers and to throttle body.
9.Connect vacuum hose to IACV housing.
10.Connect multiplugs to TP and IACV sensors.
11.Connect vacuum/breather hoses to LH
camshaft cover, 'T' piece and purge control
valve.
12.Connect small vacuum hose to purge control
valve.
13.Connect multiplug to purge control valve .

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
OVERHAUL 30-3-27
Seals - manifold chamber - from 03MY
$% 30.15.37.01
Remove
1.Release clip and disconnect vacuum enhancer
from intake hose.
2.Depress plastic collar and disconnect brake
servo vacuum hose from inlet manifold.
CAUTION: Always fit plugs to open
connections to prevent contamination.
3.Remove vacuum enhancer.
4.Disconnect multiplug from purge control valve.
5. Non NAS models: Disconnect small vacuum
pipe from purge control valve.
6. Non NAS models: Depress locking collar and
release vacuum pipe from IACV housing.
CAUTION: Always fit plugs to open
connections to prevent contamination.
7. Non NAS models: Disconnect multiplug from
IACV.8. Non NAS models: Disconnect multiplug from
TP sensor.
9. Non NAS models: Depress locking collars and
release vacuum/breather pipe from purge
control valve and LH camshaft cover. Release
clip securing hose to 'T' piece and remove pipe.
CAUTION: Always fit plugs to open
connections to prevent contamination.
10. Non NAS models: Depress locking collars and
release vacuum/breather pipes from throttle
body, LH and RH camshaft cover and remove
pipe.
CAUTION: Always fit plugs to open
connections to prevent contamination.
11. NAS models: Depress locking collars and
release vacuum/breather pipes from LH and
RH camshaft covers and release pipe from clip.
M30 1177
M30 1171
M30 1172

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
30-3-28 OVERHAUL
12. NAS models: Remove clip securing vacuum/
breather pipe to engine air intake hose and
disconnect vacuum/breather pipe from air
intake hose. Discard clip.
CAUTION: Always fit plugs to open
connections to prevent contamination.
13. NAS models: Depress locking collars and
release vacuum/breather pipe from LH
camshaft cover, RH camshaft cover link pipe
and inlet manifold chamber. Remove pipe.
CAUTION: Always fit plugs to open
connections to prevent contamination.
14. NAS models: Disconnect multiplug from IAT
and MAF sensors.
15. NAS models: Disconnect multiplug from
throttle body.
16. NAS models: Remove clip securing intake
hose to throttle body, remove intake hose and
MAF sensor assembly. Discard clip.
17. NAS models: Release harness and fuel feed
pipe from clip on inlet manifold chamber.
18.Disconnect multiplugs from VIS motors.19.Remove 2 screws securing engine harness
brackets to inlet manifold chamber and position
harness aside.
20.Release 3 locking clips and disconnect 3
multiplugs from RH plug top coils.
21.Release 2 clips securing RH plug top coil
harness to inlet manifold chamber support
brackets.
M30 1173
M30 1176

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
OVERHAUL 30-3-29
22.Remove 2 bolts securing inlet manifold
chamber rear support brackets to RH camshaft
cover.
23.Remove 4 bolts securing inlet manifold
chamber to LH inlet manifold.24.Remove and discard seals from inlet manifold
chamber and 'O' rings from RH inlet manifold.
M30 1175

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
30-3-30 OVERHAUL
Refit
1.Clean seal faces on inlet manifold chamber and
inlet manifolds.
2.Fit new 'O' rings to RH inlet manifold and new
seals to inlet manifold chamber.
3.Fit inlet manifold chamber to inlet manifolds
and tighten bolts to 18 Nm (13 lbf.ft).
4.Align inlet manifold chamber support brackets
to RH camshaft cover, fit and tighten bolts to 10
Nm (7 lbf.ft).
5.Position engine harness brackets to inlet
manifold chamber, fit and tighten screws.
6.Secure RH plug top coil harness to manifold
chamber support brackets.
7.Connect multiplugs to plug top coils and secure
with locking clips.
8.Connect multiplugs to VIS motors.
9. NAS models: Align harness and fuel feed pipe.
Secure harness and pipe in clip on manifold
chamber.
10. NAS models: Using a new clip, fit intake hose
to throttle body and secure hose with clip.
11. NAS models: Connect multiplug to throttle
body.
12. NAS models: Connect multiplugs to IAT and
MAF sensors.13. NAS models: Fit vacuum/breather pipe and
connect to LH camshaft cover, RH camshaft
cover link pipe and inlet manifold chamber.
14. NAS models: Using a new clip, fit vacuum/
breather pipe to engine air intake hose and
secure pipe with clip.
15. NAS models: Connect vacuum/breather pipe
to LH and RH camshaft covers. Fit pipe into
clip.
16. Non NAS models: Fit vacuum/breather pipe to
throttle body and connect pipe to LH and RH
camshaft covers.
17. Non NAS models: Fit vacuum/breather pipe to
purge control valve and LH camshaft cover.
Using a new clip, connect pipe to 'T' piece and
secure pipe with clip.
18. Non NAS models: Connect multiplug to TP
sensor.
19. Non NAS models: Connect multiplug to IACV.
20. Non NAS models: Connect vacuum pipe to
IACV.
21. Non NAS models: Connect small vacuum pipe
to purge control valve..
22.Connect multiplug to purge control valve .
23.Fit vacuum enhancer and connect to inlet
manifold chamber.
24.Using a new clip, connect vacuum enhancer to
intake hose and secure hose with clip.

INTERMEDIATE REDUCTION DRIVE
REPAIRS 41-3
REPAIRS
Intermediate reduction drive (IRD) unit -
Td4
$% 41.25.01.99
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove rear beam.

+ FRONT SUSPENSION, REPAIRS,
Rear beam.
4.Remove exhaust front pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- Td4, REPAIRS, Exhaust pipe - front.
5.Drain fluid from IRD.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) fluid - drain & refill -
Non NAS.
6.Drain gearbox fluid.

+ MANUAL GEARBOX - GETRAG,
ADJUSTMENTS, Gearbox oil - drain and
refill.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
7.Remove 3 bolts securing RH splash shield to
body and remove shield.8.Secure LRT-54-026 to drive shaft inboard joint.
Using a suitable lever, release drive shaft from
IRD.
9.With assistance, pull hub outwards and release
drive shaft from IRD.
10.Remove and discard drive shaft circlip.
11.Reference mark front propeller shaft for
reassembly.
12.Raise one rear wheel for rotation of propeller
shaft to access bolts.

INTERMEDIATE REDUCTION DRIVE
41-6 REPAIRS
Refit
1.Clean mating faces of IRD and gearbox.
2.Lubricate and fit new 'O' ring
3.With assistance, fit IRD.
4.Fit bolts securing IRD to gearbox and tighten
sufficiently only to pull mating faces of IRD and
gearbox together at this stage.
5.Fit IRD support brackets, tighten sufficiently to
pull mating faces together.
6.Final tighten bolts securing IRD to gearbox to
90 Nm (66 lbf.ft).
7.Final tighten bolts securing IRD support
brackets in the following sequence:
lM8 bolts securing support brackets to IRD
37 Nm (22 lbf.ft)
lM10 bolts securing support brackets to IRD
50 Nm (22 lbf.ft)
l3 bolts securing support bracket to cylinder
block 25 Nm (18 lbf.ft)
l3 bolts securing support bracket to sump at
45 Nm (33 lbf.ft).
8.Position lower engine steady, 'TOP' mark
uppermost. Fit bolt but do not tighten at this
stage.
9.Connect coolant hoses and secure with clips.
10.Connect breather hose to IRD housing.
11.Clean propeller shaft flange and mating face.
12.Fit propeller shaft to IRD flange and align
marks. Tighten nuts and bolts to 40 Nm (30
lbf.ft).
13.Inspect drive shaft oil seal, renew if worn or
damaged.14.Clean drive shaft and flange splines.
15.Fit new circlip to drive shaft.
16.With assistance, pull hub outwards, align drive
shaft and fit to IRD taking care not to damage
oil seal.
17.Fit splash shield and secure with bolts.
18.Fit exhaust front pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- Td4, REPAIRS, Exhaust pipe - front.
19.Fit rear beam.

+ FRONT SUSPENSION, REPAIRS,
Rear beam.
20.Final tighten bolt securing lower engine steady
to IRD support bracket to 100 Nm (74 lbf.ft).
21.Remove stand(s) and lower vehicle.
22.Fill IRD to correct level with fluid.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) fluid - drain & refill -
Non NAS.
23.Fill gearbox with fluid.

+ MANUAL GEARBOX - GETRAG,
ADJUSTMENTS, Gearbox oil - drain and
refill.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
24.Connect battery earth lead.
25.Refill cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.