2001 LAND ROVER FREELANDER wheel

FUEL DELIVERY SYSTEM - PETROL
19-2-42 REPAIRS
Switch - engagement (on/off) - from
04MY
$% 19.75.30
Remove
1.Release 2 clips and remove fascia mounted
switch cover.
2.Remove 2 screws securing switch carrier to
fascia.
3.Release switch carrier from fascia and
disconnect switch multiplug.
4.Remove switch assembly from carrier.
Refit
1.Fit switch to carrier.
2.Connect multiplug to switch.
3.Secure switch carrier to fascia with screws.
4.Fit and secure switch cover.
Switch - multi-purpose
$% 19.75.33
Remove
1.Remove airbag module from steering wheel.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
2.Release cruise control switch leads from clip
and disconnect multiplug.
3.Remove 2 screws securing cruise control
switch and remove switch.
Refit
1.Fit cruise control switch and secure with
screws.
2.Connect switch multiplug and fit leads in clip.
3.Fit drivers airbag.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
M19 3672

INTERMEDIATE REDUCTION DRIVE
REPAIRS 41-3
REPAIRS
Intermediate reduction drive (IRD) unit -
Td4
$% 41.25.01.99
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove rear beam.

+ FRONT SUSPENSION, REPAIRS,
Rear beam.
4.Remove exhaust front pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- Td4, REPAIRS, Exhaust pipe - front.
5.Drain fluid from IRD.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) fluid - drain & refill -
Non NAS.
6.Drain gearbox fluid.

+ MANUAL GEARBOX - GETRAG,
ADJUSTMENTS, Gearbox oil - drain and
refill.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
7.Remove 3 bolts securing RH splash shield to
body and remove shield.8.Secure LRT-54-026 to drive shaft inboard joint.
Using a suitable lever, release drive shaft from
IRD.
9.With assistance, pull hub outwards and release
drive shaft from IRD.
10.Remove and discard drive shaft circlip.
11.Reference mark front propeller shaft for
reassembly.
12.Raise one rear wheel for rotation of propeller
shaft to access bolts.

INTERMEDIATE REDUCTION DRIVE
41-8 REPAIRS
10.Reference mark front propeller shaft for
reassembly.
11.Raise one rear wheel for rotation of propeller
shaft to access bolts.
12.Remove 6 nuts and bolts securing propeller
shaft to IRD drive flange.
13.Release propeller shaft from IRD drive flange
and tie shaft aside.
CAUTION: Care must be taken to support
the Tripode joint when removed from the
IRD unit. To avoid damage to gaiter or steel
can, the joint should not be allowed to fully
extend or be dropped.
14.Remove 3 nuts securing mass damper to
pinion housing.
15.Remove mass damper.
16.Disconnect breather hose from IRD housing.
17.Position container to collect coolant spillage.
18.Release clips and disconnect coolant hoses
from IRD.19.Remove bolt securing engine lower steady to
bracket on sump.
20.Remove engine lower steady.
21.Remove 3 bolts securing lower engine steady
bracket to sump and remove bracket.
22.Remove upper bolt securing IRD support
bracket to cylinder block.
23.Remove 5 bolts securing support bracket to
IRD.
M12 7142M12 7144
M12 7165
M12 7166

INTERMEDIATE REDUCTION DRIVE
REPAIRS 41-11
12.Reference mark front propeller shaft for
reassembly.
13.Raise one rear wheel for rotation of propeller
shaft to access bolts.
14.Remove 6 nuts and bolts securing propeller
shaft to IRD drive flange.
15.Release propeller shaft from IRD drive flange
and tie shaft aside.
CAUTION: Care must be taken to support
the Tripode joint when removed from the
IRD unit. To avoid damage to gaiter or steel
can, the joint should not be allowed to fully
extend or be dropped.
16.Remove nut securing manifold heat shield to
IRD unit.
17.Remove nut securing heat shield to IRD pinion
housing.
18.Remove 2 bolts securing heat shield and
remove heat shield.19.Disconnect breather hose from IRD housing.
20.Position container to collect coolant spillage.
21.Release clips and disconnect coolant hoses
from IRD.
22.Remove bolt securing engine lower steady to
IRD support bracket.
23.Remove lower engine steady noting that 'TOP'
mark on engine steady faces uppermost.

INTERMEDIATE REDUCTION DRIVE
REPAIRS 41-25
Seal - driveshaft - RH
$% 41.29.09
Remove
1.Remove RH drive shaft.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - RH.
2.Carefully remove and discard oil seal, take care
not to damage oil seal recess.
Refit
1.Clean oil seal recess.
2.Locate seal on tool LRT-37-031 and replacer
LRT-37-027 with sealing lip facing towards
housing.
3.Carefully drift oil seal into housing until fully
seated in recess.
4.Fit RH drive shaft.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - RH.
Seal - pinion gear housing - Td4
$% 41.29.11
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Drain fluid from IRD.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) fluid - drain & refill -
Non NAS.
4.Raise one rear wheel for rotation of propeller
shaft to access bolts.
5.Reference mark front propeller shaft for
reassembly.
6.Remove 6 nuts and bolts securing propeller
shaft to IRD drive flange.
7.Release propeller shaft from IRD drive flange
and tie shaft aside.
CAUTION: Care must be taken to support
the Tripode joint when removed from the
IRD unit. To avoid damage to gaiter or steel
can, the joint should not be allowed to fully
extend or be dropped.

INTERMEDIATE REDUCTION DRIVE
REPAIRS 41-27
Seal - pinion gear housing - K1.8
$% 41.29.11
Remove
1.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
2.Drain fluid from IRD.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) fluid - drain & refill -
Non NAS.
3.Raise one rear wheel for rotation of propeller
shaft to access bolts.
4.Reference mark front propeller shaft for
reassembly.
5.Remove 6 nuts and bolts securing propeller
shaft to IRD drive flange.
6.Release propeller shaft from IRD drive flange
and tie shaft aside.
CAUTION: Care must be taken to support
the Tripode joint when removed from the
IRD unit. To avoid damage to gaiter or steel
can, the joint should not be allowed to fully
extend or be dropped.7.Remove 3 nuts securing mass damper to
pinion housing.
8.Remove mass damper.
9.Remove 2 remaining nuts securing pinion
housing.
10.Remove pinion housing.
11.Remove and discard 'O' ring.
12.Remove and retain spacing washer.
Refit
1.Clean pinion housing and mating face on IRD
casing.
2.Clean spacing washer.
3.Fit spacing washer to IRD.
4.Lubricate new 'O' ring with IRD fluid and fit to
groove in pinion housing.
5.Fit pinion housing.
6.Fit mass damper and fit nuts finger tight.
7.Fit remaining nuts securing pinion housing and
tighten all nuts to 25 Nm (18 lbf.ft).
8.Ensure mating face of propeller shaft and IRD
drive flange are clean.
9.Fit propeller shaft to IRD flange and align
marks. Tighten nuts and bolts to 40 Nm (30
lbf.ft).
10.Fill IRD to correct level with fluid.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) fluid - drain & refill -
Non NAS.
11.Lower axle and remove jack.
12.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
M12 7142

INTERMEDIATE REDUCTION DRIVE
41-28 REPAIRS
Seal - pinion gear housing - KV6 - Non
NAS
$% 41.29.11
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Drain fluid from IRD.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) fluid - drain & refill -
Non NAS.
4.Raise one rear wheel for rotation of propeller
shaft to access bolts.
5.Reference mark front propeller shaft for
reassembly.
6.Remove 6 nuts and bolts securing propeller
shaft to IRD drive flange.
7.Release propeller shaft from IRD drive flange
and tie shaft aside.
CAUTION: Care must be taken to support
the Tripode joint when removed from the
IRD unit. To avoid damage to gaiter or steel
can, the joint should not be allowed to fully
extend or be dropped.8.Remove nut securing exhaust heat shield to
mounting bracket.
9.Remove 2 nuts securing heat shield to IRD
pinion housing.
10.Remove heat shield.
11.Remove nut securing manifold heat shield to
IRD unit.
12.Remove nut securing heat shield to IRD pinion
housing.
13.Remove 2 bolts securing heat shield and
remove heat shield.

INTERMEDIATE REDUCTION DRIVE
41-30 REPAIRS
Seal - pinion gear housing - KV6 - NAS
$% 41.29.11
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Remove front exhaust pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Front pipe - NAS.
4.Drain fluid from IRD.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) lubrication system -
drain & refill - NAS.
5.Raise one rear wheel for rotation of propeller
shaft to access bolts.
6.Reference mark front propeller shaft for
reassembly.
7.Remove 6 nuts and bolts securing propeller
shaft to IRD drive flange.
8.Release propeller shaft from IRD drive flange
and tie shaft aside.
CAUTION: Care must be taken to support
the Tripode joint when removed from the
IRD unit. To avoid damage to gaiter or steel
can, the joint should not be allowed to fully
extend or be dropped.
9.Remove 2 nuts from pinion housing securing
front exhaust pipe bracket, remove bracket.
10.Remove nut securing heat shield to IRD unit,
remove shield.11.Remove 2 remaining nuts securing pinion
housing.
12.Remove pinion housing.
13.Remove and discard 'O' ring.
14.Remove and retain spacing washer.