Page 486 of 2395
SBT023A
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
BODY FRONT END
Removal and Installation (Cont'd)
BT-13
Page 488 of 2395

Removal and InstallationNBBT0005IBumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
IBack door lock system adjustment: Adjust lock & striker so that they are in the center.
After adjustment, check back door lock operation.
IBack door hatch lock system adjustment: Adjust lock & striker so that they are in the center.
After adjustment, check back door hatch lock operation.
WARNING:
IBe careful not to scratch back door stay and/or back door hatch stay when installing back door
and/or back door hatch. A scratched stay may cause gas leakage.
IThe contents of the back door stay and back door hatch stay are under pressure. Do not take apart,
puncture, apply heat or allow fire near them.
REAR BUMPER ASSEMBLYNBBT0005S011. Remove bolts and screws securing left and right mudguards and remove the mudguards.
2. Remove clips and screws securing left and right sides of wheel protector.
3. Remove clips and bolts securing left and right rear fenders to bumper fascia.
4. Remove bolts securing bumper reinforcement to bumper fascia.
5. Remove clips securing bumper fascia.
6. Extract bumper fascia assembly.
7. Remove bolts and nuts securing bumper reinforcement.
8. Extract bumper reinforcement.
SBT715
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
BODY REAR END AND OPENER
Removal and Installation
BT-15
Page 490 of 2395
SBT717
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
BODY REAR END AND OPENER
Removal and Installation (Cont'd)
BT-17
Page 492 of 2395
Front Door Limit Switch ResetNBBT0027RESET CONDITIONSNBBT0027S01After each of the following operations are performed, reset the limit
switch (with built-in motor).
IRegulator removal and installation
IRemoval of motor from regulator
IOperation of regulator as a single unit
IDoor glass removal and installation
IGlass run removal and installation
SBT041A
RESET PROCEDURESNBBT0027S02After installing parts, proceed as follows:
1. Close the door window completely.
2. Press the reset switch and open the door window completely.
3. Release the reset switch. After making sure the reset switch
has returned to the original position, close the door window
completely.
4. The limit switch is now reset.
CAUTION:
Be sure to manually open or close the door window. (Do not
use the automatic open-close procedures.)
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
FRONT DOOR
Front Door Limit Switch Reset
BT-19
Page 494 of 2395
Removal and InstallationNBBT0008CAUTION:
IDisconnect both battery cables in advance.
IDisconnect air bag system line in advance.
INever tamper with or force air bag lid open, as this may
adversely affect air bag performance.
IBe careful not to scratch pad and other parts.
SBT042A
*1 RS-17 *2 BT-28
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
BT-21
Page 496 of 2395
SBT038A
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
BT-23
Page 498 of 2395
SBT029A
Steering column cover
After removing the screws, release the pawls by pressing on the
upper cover where it meets (the bottom cover) from both sides.
SBT030A
Instrument lower panel on the driver side
Open the pocket after removing the screws. Hold the opening and
the bottom and pull out horizontally.
SBT044A
Cluster lid A
After removing the screws, hold the bottom and pull out.
CAUTION:
Cover the surroundings with a cloth to prevent damage.
SBT031A
Center ventilator
Hook a cloth-covered flat-bladed screwdriver into the right-side
groove section, and pull out.
CAUTION:
To prevent the screwdriver from slipping and causing damage
to the surface, pull out while applying pressure on the screw-
driver towards the right.
SBT045A
Cluster lid C
After removing the screws, place hands on the metal clip section,
and pull forward to remove the metal clips.
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
BT-25
Page 500 of 2395

SBT035A
Defroster grille
REMOVAL
Insert a cloth-covered flat-bladed screwdriver into the grilles of the
outside, center and central grilles, respectively, lift up the front of
the grilles and remove.
INSTALLATION
After inserting the front section, insert the rear section (pawls) to
attach.
CAUTION:
Confirm that the pawls at the rear are securely attached.
SBT036A
Side ventilator-left
Insert a cloth-covered flat-bladed screwdriver into the lower
section, and pull out forward.
SBT037A
Side ventilator-right
Insert a cloth-covered flat-bladed screwdriver into the corner of the
lower section, and pull out forward. (Securely press the screwdriver
against the ventilator.) Or, after removing the instrument lower
panel, push the ventilator out from the back.
Side defroster grille
After removing the side ventilator, reach in with hands from the
opening, push on the pawls from behind the grille, and remove by
pushing out.
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
BT-27