2001 HONDA ACCORD SEDAN engine

Cooling System

Adding Engine Coolant
If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system for leaks.
This coolant should always be a mixture of 50 percent antifreeze and50 percent water. Never add straight
antifreeze or plain water. Always use Genuine Honda All
Season Antifreeze/Coolant Type 2.
This coolant is pre-mixed with 50 percent antifreeze and 50 percent
water. It does not require anyadditional mixing. If it is not available,
you may use another major-brand non-silicate coolant as a temporary
replacement. Make sure it is a high-quality coolant recommended for
aluminum engines. However,
continued use of any non-Honda coolant can result in corrosion,
causing the cooling system to malfunction or fail. Have the cooling
system flushed and refilled with
Honda antifreeze/coolant as soon as

possible.

If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
CONTINUED
Maintenance
4-cylinder models

RESERVE TANK
RESERVE TANK

6-cylinder models

Cooling System

1. Make sure the engine and radiator
are cool.

2. Turn the radiator cap counter- clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
3. Remove the radiator cap by
pushing down and turning

counterclockwise.

4. The coolant level should be up to the base of the filler neck. Add
coolant if it is low.
5. Put the radiator cap back on. Tighten it fully.
Maintenance
RADIATOR CAP

4-cylinder models 6-cylinder models

RADIATOR CAP
Removing the radiator cap
while the engine is hot can cause the coolant to spray out,
seriously scalding you.
Always let the engine and radiator cool down before
removing the radiator cap.

Cooling System
6. Pour coolant into the reserve tank. Fill it to halfway between the MAX
and MIN marks. Put the cap back
on the reserve tank. Do not add any rust inhibitors or
other additives to your car's cooling
system. They may not be compatible
with the coolant or engine compo- nents. Replacing Engine Coolant
The cooling system should be completely drained and refilled with
new coolant according to the timeand distance recommendations in
the maintenance schedule. Only use Honda All season Antifreeze/
Coolant Type 2.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance done by a skilled mechanic.

CONTINUED

Maintenance

4 cylinder models
RESERVE TANK

6-cylinder models
RESERVE TANK

Cooling System

1. Open the hood. Make sure the engine and radiator are cool to the

touch.

Except EX- V6 model

Turn the ignition ON (II). Turn the temperature control Dial all
the way clockwise. Turn off theignition and remove the key.
EX-V6 model

Turn the ignition ON (II). Turn the temperature control dial to90°F (32° C). Turn off the ignition
and remove the key.
2. Remove the radiator cap.
4-cylinder models

3. Loosen the drain plug on the bottom of the radiator. Thecoolant will drain through the
splash guard. Remove the drain
bolt and washer from the engine
block.

Maintenance
DRAIN

BOLT

DRAIN

PLUG

6-cylinder models
4-cylinder models

4-cylinder models

Cooling System

5. When the coolant stops draining, tighten the drain plug at the
bottom of the radiator.

6. 4-cylinder models
Put a new washer on the drain bolt,
then reinstall the drain bolt in the
engine block. Tighten it securely.
Tightening torque:
61 Ibf.ft (83 N.m , 8.5 kgf.m)
6-cylinder models

Tighten the drain bolt at the rear of the engine cylinder block
securely.

Tightening torque:
7 Ibf.ft (10 N.m, 1.0 kgf.m)
7. 4-cylinder models

Loosen the bleeder bolt on top of
the engine.
Pour Honda All Season
Antifreeze/Coolant Type 2 into the radiator. This coolant is a
mixture of 50 percent anti-freezeand 50 percent water. Pre-mixing
is not required.
Tighten the bleeder bolt when coolant comes out in a steadystream with no bubbles.

Maintenance

RESERVE TANK
RESERVE TANK CAP
HOLDER

6-cylinder models 4-cylinder models

Fill up to here
FILLER NECK
FILLER NECK
Fill up to here

6-cylinder models

Cooling System

6-cylinder models

Pour coolant into the radiator up

to the base of the filler neck.

The cooling system capacity is:
With 5-speed manual transmission:
1.45 US gal (5.5 ,1.21 Imp gal)

With automatic transmission:
1.43 US gal (5.4 ,1.19 Imp gal)
6-cylinder models 1.48 US gal (5.6 ,1.23 Imp gal) 8. Start the engine and let it run for
about 30 seconds. Then turn off
the engine.
9. Fill the radiator with coolant up to the base of the filler neck.
10. Fill the reserve tank to the MAX mark. Install the reserve tank cap.
11.Install the radiator cap, and tighten it to the first stop.
12.Start the engine and let it run until the radiator cooling fan comes onat least twice. Then stop the

engine.

13.Remove the radiator cap. Pour coolant into the radiator up to the
base of the filler neck and into the
reserve tank up to the MAX mark. 14.Start the engine and hold it at
1,500 rpm until the cooling fan
comes on. Turn off the engine. Check the coolant level in the
radiator and add coolant if needed.
15.Install the radiator cap, and tighten it fully.
16.If necessary, fill the reserve tank to the MAX mark. Install thereserve tank cap.

Maintenance

4-cylinder models

BLEEDER BOLT

Windshield Washers

Check the level in the windshield
washer reservoir at least monthly
during normal usage. In bad weather,

when you use the washers often,
check the level every time you stop

for fuel.

The windshield washer reservoir is
located behind the headlight.

Check the reservoir's fluid level by

removing the cap and looking at the
level gauge attached to the cap.

Canadian Models
The low washer level indicator will light when the level is low (see page 57 ).
Fill the reservoir with a good-quality
windshield washer fluid. This increases the cleaning capability and
prevents freezing in cold weather.
Do not use engine antifreeze or a
vinegar/water solution in the

windshield washer reservoir.

Antifreeze can damage your car's paint,
while a vinegar/water solution can

damage the windshield washer pump.

Use only commercially-available

windshield washer fluid.
When you refill the reservoir, clean
the edges of the windshield wiper
blades with windshield washer fluid on a clean cloth. This will help to
condition the blade edges.
Maintenance LEVEL GAUGE
4-cylinder models 6-cylinder models

NOTICE

Transmission Fluid

Automatic Transmission
4-cylinder models

Check the fluid level with the engine
at normal operating temperature.
1. Park the car on level ground. Shut off the engine.
2. Remove the dipstick (yellow loop) from the transmission and wipe it
with a clean cloth. 3. Insert the dipstick all the way into
the transmission securely asshown in the illustration.
4. Remove the dipstick and check the fluid level. It should be
between the upper and lower marks. 5. If the level is below the lower
mark, add fluid into the tube to
bring it to the upper mark. Always use Honda ATF-Z1 (Automatic
Transmission Fluid). If it is not available, you may use a
DEXRON ®
III automatic
transmission fluid as a temporary
replacement. However, continued
use can affect shift quality. Have
the transmission drained and refilled with Honda ATF-Z1as soon as it is convenient.
To thoroughly flush the transmission, the technician should drain and refillit with Honda ATF-Z1 (Automatic
Transmission Fluid), then drive the vehicle a short distance.Do this three times. Then drain and
refill the transmission a final time.

CONTINUED

Maintenance

DIPSTICK

UPPER MARK
LOWER MARK