2001 BUICK LESABRE driver seat adjustment

1-2
Seats and Seat Controls
This section tells you about the power seats -- how to
adjust them and also about reclining seatbacks, lumbar
adjustments, heated seats and head restraints.
Manual Front Seat
CAUTION:
You can lose control of the vehicle if you try to
adjust a manual driver's seat while the vehicle is
moving. The sudden movement could startle and
confuse you, or make you push a pedal when you
don't want to. Adjust the driver's seat only when
the vehicle is not moving.
Pull up on the control bar located under the front of the
seat to unlock it. Slide the seat to where you want it.
Then release the bar and try to move the seat with your
body to make sure the seat is locked into place.
Manual Lumbar Support
The knob that controls this feature is located on the
outboard side of the seat. Turn the knob towards the front
of the vehicle to increase lumbar support. Turn the knob
towards the rear of the vehicle to decrease lumbar support.

1-4 Memory Seat and Mirrors (If Equipped)
If your vehicle has this feature, the controls on the driver's
door panel are used to program and recall previous settings.
You can use this feature to save your driver's seat position,
lumbar adjustment, outside mirror positions, personalization
features, comfort controls and radio settings.
Adjust the driver's seat (including the lumbar adjustments)
and both outside mirrors to the position you would like
for driving. Then press and hold memory button 1 for more
than three seconds. A double beep will sound when the
memory is set.
To set the seat and mirror positions for a second driver,
follow the previous steps, but press button 2 instead.You can also store an exit position for each driver.
The exit position is programmed by moving the seat to
the desired exit position and then holding the exit button
for more than three seconds. The exit position set will be
for the most recently selected driving position (1 or 2).
Please note that mirror and lumbar positions will not be
stored or recalled for the exit position.
To recall your memory positions, your vehicle must be in
PARK (P). Push and release the memory button (1 or 2)
corresponding to the desired driving position. The seat and
mirrors will move to the position previously stored for the
identified driver. You will hear one beep.
To recall the exit position, your vehicle must be in
PARK (P). Push and release the EXIT button and the
seat will move to the exit position previously stored for
the current identified driver. You will hear one beep.
If an exit position has not been stored for the current
identified driver, the seat will move all the way back.
To stop recall movement of the seat at any time, press
the driver's power seat control located on the outboard
side of the front seat.
If you would like your stored driving or exit position to be
recalled when unlocking your vehicle with the transmitter,
see ªDIC Personal Choice Programmingº in the Index.

6-35
If your vehicle is damaged in an accident, the headlamp
aim may be affected. Aim adjustment to the low beam
may be necessary if it is difficult to see lane markers
(for horizontal aim), or if oncoming drivers flash their
high beams at you (for vertical aim). If you believe your
headlamps need to be re
-aimed, we recommend that
you take your vehicle to your dealer for service.
However, it is possible for you to re
-aim your
headlamps as described in the following procedure.
NOTICE:
To make sure your headlamps are aimed
properly, read all the instructions before
beginning. Failure to follow these instructions
could cause damage to headlamp parts.
The vehicle should be properly prepared as follows:

The vehicle should be placed so the headlamps
are 25 ft. (7.6 m) from a light colored wall or
other flat surface.

The vehicle must have all four tires on a perfectly
level surface which is level all the way to the wall or
other flat surface.

The vehicle should be placed so it is perpendicular to
the wall or other flat surface.

The vehicle should not have any snow, ice or mud
attached to it.

The vehicle should be fully assembled and all other
work stopped while headlamp aiming is being done.

The vehicle should be normally loaded with a full
tank of fuel and one person or 160 lbs. (75 kg) on
the driver's seat.

Tires should be properly inflated.
Headlamp aiming is done with the vehicle low beam
lamps. The high beam lamps will be correctly aimed
if the low beam lamps are aimed properly.