Page 65 of 86
1
2
3
4
5
6
7
8
9
6-35
PERIODIC MAINTENANCE AND MINOR REPAIR
1
3. Unhook the headlight bulb hold-
er, and then remove the defec-
tive bulb.
EW000119
w
Headlight bulbs get very hot.
Therefore, keep flammable prod-
ucts away from a lit headlight bulb,
and do not touch the bulb until it
has cooled down.
4. Place a new bulb into position,
and then secure it with the bulb
holder.
1. Bulb holder
EC000105
cC
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be
adversely affected. Thoroughly
clean off any dirt and fingerprints
on the headlight bulb using a cloth
moistened with alcohol or thinner.
5. Install the bulb cover, and then
connect the coupler.
1. Do not touch this area
1
6. Install the headlight unit by
installing the screws.
7. Have a Yamaha dealer adjust
the headlight beam if necessary.
5JX-9-E0 4/9/0 4:11 AM Page 63
Page 66 of 86
6-36
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU03218
Replacing a turn signal light
bulb
1. Remove the turn signal lens by
removing the screws.
1. Screw (´2)
1
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
cC
Do not overtighten the screws,
otherwise the lens may break.
1. Bulb
1
1
EAU01623
Replacing the tail/brake light
bulb
1. Remove the tail/brake light lens
by removing the screws.
1. Screw (´2)
5JX-9-E0 4/9/0 4:11 AM Page 64
Page 67 of 86
1
2
3
4
5
6
7
8
9
6-37
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
cC
Do not overtighten the screws,
otherwise the lens may break.
1. Bulb
EAU01579
Supporting the motorcycle
Since this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other main-
tenance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed
under the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.To service the rear wheel
Raise the rear wheel off the ground
by using a motorcycle stand or, if a
motorcycle stand is not available, by
placing a jack either under each side
of the frame in front of the rear wheel
or under each side of the swingarm.
5JX-9-E0 4/9/0 4:11 AM Page 65
Page 68 of 86
6-38
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU03239
Front wheel
To remove the front wheelEW000122
w
8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so that there is no danger
of it falling over.
1. Disconnect the speedometer
cable from the front wheel.
1. Speedometer cable
1
2. Loosen the front wheel axle
pinch bolt, then the wheel axle.
3. Lift the front wheel off the ground
according to the procedure on
page 6-37.
4. Pull the wheel axle out, and then
remove the wheel.
ECA00048
cC
Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
1. Front wheel axle pinch bolt
2. Wheel axle
1 2
EAU01394
To install the front wheel
1. Install the speedometer gear unit
into the wheel hub so that the
projections mesh with the slots.
2. Lift the wheel up between the
fork legs.
NOTE:
Make sure that there is enough
space between the brake pads
before inserting the brake disc and
that the slot in the speedometer gear
unit fits over the retainer on the fork
leg.
5JX-9-E0 4/9/0 4:11 AM Page 66
Page 69 of 86
1
2
3
4
5
6
7
8
9
6-39
PERIODIC MAINTENANCE AND MINOR REPAIR
3. Insert the wheel axle.
4. Lower the front wheel so that it is
on the ground.
5. Push down hard on the handle-
bar several times to check for
proper fork operation.
6. Tighten the wheel axle to the
specified torque.
Tightening torque:
Wheel axle:
59 Nm (5.9 m·kg)
7. Install the front wheel axle pinch
bolt, and then tighten it to the
specified torque.
8. Connect the speedometer cable.
EAU03189
Rear wheel
To remove the rear wheelEW000122
w
8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so that there is no danger
of it falling over.
1. Loosen the axle nut and the
brake torque rod nut at the brake
shoe plate.
1. Axle nut
1
Tightening torque:
Front wheel axle pinch bolt:
20 Nm (2.0 m·kg)
5JX-9-E0 4/9/0 4:11 AM Page 67
Page 70 of 86
6-40
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
2. Lift the rear wheel off the ground
according to the procedure on
page 6-37.
3. Disconnect the brake torque rod
from the brake shoe plate by
removing the nut and the bolt.
4. Remove the brake pedal free
play adjusting nut, and then dis-
connect the brake rod at the
brake camshaft lever.
1. Brake torque rod
2. Brake torque rod nut
3. Brake rod
4. Brake pedal free play adjusting nut
1
2
34
5. Loosen the locknut and the drive
chain adjusting nut on both ends
of the swingarm.
6. Remove the axle nut, and then
pull the wheel axle out.
7. Push the wheel forward, and
then remove the drive chain from
the rear sprocket.
NOTE:
The drive chain does not need to be
disassembled in order to remove and
install the wheel.
8. Remove the wheel.
1. Wheel axle
2. Drive chain adjusting nut
3. Locknut
312
EAU03190
To install the rear wheel
1. Insert the wheel axle from the
left-hand side, and then install
the drive chain onto the rear
sprocket.
2. Install the axle nut, and then
lower the rear wheel so that it is
on the ground.
3. Install the brake rod onto the
brake camshaft lever, and then
install the brake pedal free play
adjusting nut onto the brake rod.
4. Connect the brake torque rod to
the brake shoe plate by installing
the bolt and the nut, and then
tighten the bolt to the specified
torque.
5. Adjust the drive chain slack.
(See page 6-26 for drive chain
slack adjustment procedures.) Tightening torque:
Brake torque rod bolt:
23 Nm (2.3 m·kg)
5JX-9-E0 4/9/0 4:11 AM Page 68
Page 71 of 86
1
2
3
4
5
6
7
8
9
6-41
PERIODIC MAINTENANCE AND MINOR REPAIR
6. Tighten the axle nut to the speci-
fied torque.
7. Adjust the brake pedal position
and free play. (See page 6-21 for
brake pedal position and free
play adjustment procedures.)
EW000103
w
After adjusting the brake pedal
free play, check the operation of
the brake light.
EAU01008
Troubleshooting
Although Yamaha motorcycles
receive a thorough inspection before
shipment from the factory, trouble
may occur during operation. Any
problem in the fuel, compression, or
ignition systems, for example, can
cause poor starting and loss of
power.
The following troubleshooting chart
represents a quick and easy proce-
dure for checking these vital systems
yourself. However, should your
motorcycle require any repair, take it
to a Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service
the motorcycle properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life
and can lead to expensive repair
bills. Tightening torque:
Axle nut:
104 Nm (10.4 m·kg)
5JX-9-E0 4/9/0 4:11 AM Page 69
Page 72 of 86
6-42
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU01297
Troubleshooting chartEW000125
w
Keep away open flames and do not smoke while checking or working on the fuel system.
1. Fuel
2. Compression
3. Ignition
4. Battery
Remove the spark
There is compression.
There is no compression.Check the ignition.
Have a Yamaha dealer check the vehicle.
Wet
DryWipe off with a dry cloth and correct the spark
Have a Yamaha dealer check the vehicle.
The engine turns
The engine turnsThe battery is good.
Check the battely lead connections,
Check the fuel level
There is enough fuel.
There is no fuel.Check the compression.
in the fuel tank.
the electrodes. plugs and check
over quickly.
over slowly. and charge the battery if necessary.Open the throttle halfway and
The engine does not start.Check the battery.operate the electric starter. plug gaps, or replace the spark plugs.
Supply fuel.The engine does not start. Check the compression.
Operate the electric
starter. Operate the
electric starter.
The engine does not start.
Have a Yamaha dealer
check the vehicle.
5JX-9-E0 4/9/0 4:11 AM Page 70
