2000 YAMAHA XVS125 wheel

6-26
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU03187
To adjust the drive chain slack
1. Loosen the brake pedal free play
adjusting nut, the axle nut, and
the chain puller locknut at each
end of the swingarm.
1. Brake pedal free play adjusting nut
2. Drive chain puller locknut
2
1
1. Axle nut
1
2. To tighten the drive chain, turn
the adjusting nut at each end of
the swingarm in direction a. To
loosen the drive chain, turn the
adjusting nut at each end of the
swingarm in direction b, and
then push the rear wheel for-
ward.
NOTE:
Using the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same
position for proper wheel alignment.
1. Alignment marks
2. Drive chain adjusting nut
3. Locknut
312
b
a
5JX-9-E0 4/9/0 4:11 AM Page 54

6-30
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
To check the operation
1. Place the motorcycle on a level
surface and hold it in an upright
position.
2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and
rebounds smoothly.
EC000098
cC
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or
repair it.
2. Hold the lower ends of the front
fork legs and try to move them
forward and backward. If any
free play can be felt, have a
Yamaha dealer check or repair
the steering.
EAU00794
Checking the steering
Worn or loose steering bearings may
cause danger. Therefore, the opera-
tion of the steering must be checked
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
1. Place a stand under the engine
to raise the front wheel off the
ground.
EW000115
w
Securely support the motorcycle
so that there is no danger of it
falling over.
5JX-9-E0 4/9/0 4:11 AM Page 58

1
2
3
4
5
6
7
8
9
6-31
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU01144
Checking the wheel bearings
The front and rear wheel bearings
must be checked at the intervals
specified in the periodic maintenance
and lubrication chart. If there is play
in the wheel hub or if the wheel does
not turn smoothly, have a Yamaha
dealer check the wheel bearings.
EAU01271
Battery
This motorcycle is equipped with a
sealed-type (MF) battery, which does
not require any maintenance. There
is no need to check the electrolyte or
to add distilled water.
1. Battery
1
To charge the battery
Have a Yamaha dealer charge the
battery as soon as possible if it
seems to have discharged. Keep in
mind that the battery tends to dis-
charge more quickly if the motorcycle
is equipped with optional electrical
accessories.
5JX-9-E0 4/9/0 4:11 AM Page 59

1
2
3
4
5
6
7
8
9
6-37
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
cC
Do not overtighten the screws,
otherwise the lens may break.
1. Bulb
EAU01579
Supporting the motorcycle
Since this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other main-
tenance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed
under the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.To service the rear wheel
Raise the rear wheel off the ground
by using a motorcycle stand or, if a
motorcycle stand is not available, by
placing a jack either under each side
of the frame in front of the rear wheel
or under each side of the swingarm.
5JX-9-E0 4/9/0 4:11 AM Page 65

6-38
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU03239
Front wheel
To remove the front wheelEW000122
w
8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so that there is no danger
of it falling over.
1. Disconnect the speedometer
cable from the front wheel.
1. Speedometer cable
1
2. Loosen the front wheel axle
pinch bolt, then the wheel axle.
3. Lift the front wheel off the ground
according to the procedure on
page 6-37.
4. Pull the wheel axle out, and then
remove the wheel.
ECA00048
cC
Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
1. Front wheel axle pinch bolt
2. Wheel axle
1 2
EAU01394
To install the front wheel
1. Install the speedometer gear unit
into the wheel hub so that the
projections mesh with the slots.
2. Lift the wheel up between the
fork legs.
NOTE:
Make sure that there is enough
space between the brake pads
before inserting the brake disc and
that the slot in the speedometer gear
unit fits over the retainer on the fork
leg.
5JX-9-E0 4/9/0 4:11 AM Page 66

1
2
3
4
5
6
7
8
9
6-39
PERIODIC MAINTENANCE AND MINOR REPAIR
3. Insert the wheel axle.
4. Lower the front wheel so that it is
on the ground.
5. Push down hard on the handle-
bar several times to check for
proper fork operation.
6. Tighten the wheel axle to the
specified torque.
Tightening torque:
Wheel axle:
59 Nm (5.9 m·kg)
7. Install the front wheel axle pinch
bolt, and then tighten it to the
specified torque.
8. Connect the speedometer cable.
EAU03189
Rear wheel
To remove the rear wheelEW000122
w
8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so that there is no danger
of it falling over.
1. Loosen the axle nut and the
brake torque rod nut at the brake
shoe plate.
1. Axle nut
1
Tightening torque:
Front wheel axle pinch bolt:
20 Nm (2.0 m·kg)
5JX-9-E0 4/9/0 4:11 AM Page 67

6-40
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
2. Lift the rear wheel off the ground
according to the procedure on
page 6-37.
3. Disconnect the brake torque rod
from the brake shoe plate by
removing the nut and the bolt.
4. Remove the brake pedal free
play adjusting nut, and then dis-
connect the brake rod at the
brake camshaft lever.
1. Brake torque rod
2. Brake torque rod nut
3. Brake rod
4. Brake pedal free play adjusting nut
1
2
34
5. Loosen the locknut and the drive
chain adjusting nut on both ends
of the swingarm.
6. Remove the axle nut, and then
pull the wheel axle out.
7. Push the wheel forward, and
then remove the drive chain from
the rear sprocket.
NOTE:
The drive chain does not need to be
disassembled in order to remove and
install the wheel.
8. Remove the wheel.
1. Wheel axle
2. Drive chain adjusting nut
3. Locknut
312
EAU03190
To install the rear wheel
1. Insert the wheel axle from the
left-hand side, and then install
the drive chain onto the rear
sprocket.
2. Install the axle nut, and then
lower the rear wheel so that it is
on the ground.
3. Install the brake rod onto the
brake camshaft lever, and then
install the brake pedal free play
adjusting nut onto the brake rod.
4. Connect the brake torque rod to
the brake shoe plate by installing
the bolt and the nut, and then
tighten the bolt to the specified
torque.
5. Adjust the drive chain slack.
(See page 6-26 for drive chain
slack adjustment procedures.) Tightening torque:
Brake torque rod bolt:
23 Nm (2.3 m·kg)
5JX-9-E0 4/9/0 4:11 AM Page 68

1
2
3
4
5
6
7
8
9
7-1
EAU03224*
MOTORCYCLE CARE AND STORAGE
Care
While the open design of a motorcy-
cle reveals the attractiveness of the
technology, it also makes it more vul-
nerable. Rust and corrosion can
develop even if high-quality compo-
nents are used. A rusty exhaust pipe
may go unnoticed on a car, however,
it detracts from the overall appear-
ance of a motorcycle. Frequent and
proper care does not only comply
with the terms of the warranty, but it
will also keep your motorcycle looking
good, extend its life and optimize its
performance.Before cleaning
1. Cover the muffler outlets with
plastic bags after the engine has
cooled down.
2. Make sure that all caps and cov-
ers as well as all electrical cou-
plers and connectors, including
the spark plug caps, are tightly
installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets,
sprockets, the drive chain and
wheel axles. Always rinse the dirt
and degreaser off with water.CleaningECA00010
cC
8Avoid using strong acidic
wheel cleaners, especially on
spoked wheels. If such prod-
ucts are used on hard-to-
remove dirt, do not leave the
cleaner on the affected area
any longer than instructed.
Also, thoroughly rinse the area
off with water, immediately dry
it, and then apply a corrosion
protection spray.
8Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.
5JX-9-E0 4/9/0 4:11 AM Page 71