Page 49 of 87
L
6-11
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
1. Air filter case cover
2. Tab
3. Holder
4. Air filter
5. Slide the air filter case cover so as
to unhook the tab on the rear of
the cover from the holder on the
frame. Then lift the air filter case
cover upward without removing it.
6. Pull out the air filter element and
tap it lightly to remove most of the
dust and dirt. Blow out the remain-
ing dirt with compressed air as
shown. If the air filter element is
damaged, replace it.7. Reassemble by reversing the re-
moval procedure.
EC000082
CAUTION:
lMake sure the air filter is prop-
erly seated in the air filter case.
lThe engine should never be run
without the air filter installed.
Excessive piston and/or cylin-
der wear may result.
Page 50 of 87
R
6-12
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
1. Washer
2. Rubber damper
3. Spacer
EW000131
Make sure that the fuel hoses and
vacuum hose are properly connect-
ed, in place and not pinched. If a
hose is damaged, be sure to replace
it.
EC000086
CAUTION:
When reinstalling the fuel tank hold-
ing bolts, make sure that the wash-
ers, damper rubbers and spacers
are positioned properly.
EAU00630
Carburetor adjustment
The carburetors are important parts of
the engine and require very sophisti-
cated adjustment. Most adjustments
should be left to a Yamaha dealer who
has the professional knowledge and
experience to do so. However, the idle
speed may be adjusted by the owner
as part of routine maintenance.
EC000095
CAUTION:
The carburetors were set at the
Yamaha factory after many tests. If
they are changed, poor engine per-
formance and damage may result.
Page 51 of 87
L
6-13
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
EAU01168
Idle speed adjustment
NOTE:
A diagnostic tachometer must be used
for this procedure.
1. Attach the tachometer. Start the
engine and warm it up for a few
minutes at approximately 1,000 to
2,000 r/min. Occasionally rev the
engine to 4,000 to 5,000 r/min.
The engine is warm when it quick-
ly responds to the throttle.
1. Throttle stop screw
2. Set the idle to the specified engine
speed by adjusting the throttle
stop screw. Turn the screw in di-
rectiona
to increase engine
speed and in direction b
to de-
crease engine speed.
NOTE:
If the specified idle speed cannot be
obtained by performing the above ad-
justment, consult a Yamaha dealer.Standard idle speed:
1,150 ~ 1,250 r/min
a. Free play
EAU00635
Throttle cable free play
inspection
There should be a free play of 3 ~
5 mm at the throttle grip. If the free play
is incorrect, ask a Yamaha dealer to
make this adjustment.
Page 52 of 87
R
6-14
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
EAU00637
Valve clearance adjustment
The correct valve clearance changes
with use, resulting in improper fuel/air
supply or engine noise. To prevent this,
the valve clearance must be adjusted
regularly. This adjustment however,
should be left to a professional
Yamaha service technician.
EAU00647
Tires
To ensure maximum performance,
long service, and safe operation, note
the following:
Tire air pressure
Always check and adjust the tire pres-
sure before operating the motorcycle.
EW000082
Tire inflation pressure should be
checked and adjusted when the
temperature of the tire equals the
ambient air temperature. Tire infla-
tion pressure must be adjusted ac-
cording to total weight of cargo,
rider, passenger, and accessories
(fairing, saddlebags, etc. if approved
for this model), and vehicle speed.
Maximum load*220 kg (except for CH, A)
218 kg (for CH, A)
Cold tire pressure Front Rear
Up to 90 kg200 kPa
(2.00 kg/cm
2,
2.00 bar)225 kPa
(2.25 kg/cm2,
2.25 bar)
90 kg load ~
Maximum load*200 kPa
(2.00 kg/cm
2,
2.00 bar)250 kPa
(2.50 kg/cm2,
2.50 bar)
* Load is the total weight of cargo, rider, passenger
and accessories.
Page 53 of 87
L
6-15
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
EW000083
Proper loading of your motorcycle
is important for several characteris-
tics of your motorcycle, such as
handling, braking, performance and
safety. Do not carry loosely packed
items that can shift. Securely pack
your heaviest items close to the
center of the motorcycle, and dis-
tribute the weight evenly from side
to side. Properly adjust the suspen-
sion for your load, and check the
condition and pressure of your tires.
NEVER OVERLOAD YOUR MOTOR-
CYCLE. Make sure the total weight
of the cargo, rider, passenger, and
accessories (fairing, saddlebags,
etc. if approved for this model) does
not exceed the maximum load of the
motorcycle. Operation of an over-
loaded motorcycle could cause tire
damage, an accident, or even injury.
a. Tread depth
1. Side wall
Tire inspection
Always check the tires before operating
the motorcycle. If center tread depth
reaches the limit as shown, if the tire
has a nail or glass fragments in it, or if
the side wall is cracked, contact a
Yamaha dealer immediately and have
the tire replaced.
NOTE:
These limits may be different by regula-
tion from country to country. If so, con-
form to the limits specified by the
regulations of your own country.
FRONT
Manufacturer Size Type
Bridgestone 3.00-19 49S L303A
Dunlop 3.00-19 49S F14G
REAR
Manufacturer Size Type
Bridgestone 140/90-15 M/C 70S G508
Dunlop 140/90-15 M/C 70S K425
Minimum tire tread depth
(front and rear)1.6 mm
Page 54 of 87
R
6-16
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
EAU00681
lOperating the motorcycle with
excessively worn tires decrease
riding stability and can lead to
loss of control. Have excessive-
ly worn tires replaced by a
Yamaha dealer immediately.
Brakes, tires, and related wheel
parts replacement should be
left to a Yamaha Service Techni-
cian.
lPatching a punctured tube is
not recommended. If it is abso-
lutely necessary to do so, use
great care and replace the tube
as soon as possible with a good
quality replacement.
EAU00685
Wheels
To ensure maximum performance,
long service, and safe operation, note
the following:
lAlways inspect the wheels before
a ride. Check for cracks, bends or
warpage of the wheel. Be sure the
spokes are tight and undamaged.
If any abnormal condition exists in
a wheel, consult a Yamaha dealer.
Do not attempt even small repairs
to the wheel. If a wheel is de-
formed or cracked, it must be re-
placed.
lTires and wheels should be bal-
anced whenever either one is
changed or replaced. Failure to
have a wheel balanced can result
in poor performance, adverse han-
dling characteristics, and short-
ened tire life.
lRide at moderate speeds after
changing a tire since the tire sur-
face must first be broken in for it to
develop its optimal characteristics.
Page 55 of 87
L
6-17
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
1. Locknut
2. Adjusting bolt
c. Free play
EAU00694
Clutch lever free play
adjustment
The clutch lever free play should be ad-
justed to 10 ~ 15 mm.
1. Loosen the locknut at the clutch le-
ver.
2. Turn the adjusting bolt at the
clutch lever in direction a
to in-
crease free play or in direction b
to decrease free play.
3. Tighten the locknut at the clutch
lever.
1. Locknut
2. Adjusting nut
If the specified free play cannot be ob-
tained, proceed with the following steps.
4. Loosen the locknut at the clutch le-
ver.
5. Turn the adjusting bolt at the
clutch lever in direction a
to loos-
en the cable.
6. Loosen the locknut at the crank-
case side.
7. Turn the adjusting nut at the
crankcase in direction a
to in-
crease free play or in direction b
to decrease free play.
8. Tighten the locknut at the crank-
case and the clutch lever.
1. Adjusting bolt
2. Locknut
c. Free play
EAU00696
Front brake lever free play
adjustment
The free play at the front brake lever
should be 2 ~ 5 mm.
1. Loosen the locknut.
2. Turn the adjusting bolt in direction
a
to increase free play or in direc-
tionb
to decrease free play.
3. After adjusting, tighten the locknut.
Page 56 of 87
R
6-18
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
EW000099
lCheck the brake lever free play.
Be sure the brake is working
properly.
lA soft or spongy feeling in the
brake lever can indicate the
presence of air in the brake sys-
tem. This air must be removed
by bleeding the brake system
before the motorcycle is operat-
ed. Air in the system will cause
greatly diminished braking ca-
pability and can result in loss of
control and an accident. Have a
Yamaha dealer inspect and
bleed the system if necessary.
1. Footrest
2. Pedal height
a. Free play
EAU00711
Rear brake pedal height and
free play adjustment
EW000104
It is advisable to have a Yamaha
dealer make this adjustment.
The brake pedal height should be ad-
justed before adjusting the brake pedal
free play.
Pedal height
The brake pedal should be positioned
approximately 38 mm above the top of
the footrest.
1. Adjusting bolt
2. Locknut
1. Loosen the locknut.
2. Turn the adjusting bolt in direction
a
to raise pedal height or in direc-
tionb
to lower pedal height.
3. Tighten the locknut.
EW000105
After adjusting the pedal height ad-
just brake pedal free play.
