6-25
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EC000096
cC
Too little chain slack will overload
the engine and other vital parts.
Keep the slack within the specified
limits.
4. Tighten the wheel axle nut to
the specified torque.
5. Adjust the brake pedal free
play.
EW000103
w
Check the operation of the brake
light after adjusting the rear brake.
EAU01106*Drive chain lubrication
The chain consists of many parts
which work with each other. If the
chain is not maintained properly, it
will wear out quickly. Therefore,
the chain must be serviced regular-
ly. This service is especially neces-
sary when riding in dusty areas.
The drive chain should be lubri-
cated every 500 km. First, remove
all dirt and mud from the chain
with a brush or cloth. Then, spray
any of the many brands of spray-
type chain lubricant between
both rows of side plates and on
all center rollers.
To clean the chain thoroughly,
remove it from the motorcycle,
dip it in solvent, and clean out as
much dirt as possible. Then, take
the chain out of the solvent to
dry it, and immediately lubricate
it to prevent it from rusting.
EC000097
cC
Be sure to oil the chain after wash-
ing the motorcycle or riding in the
rain.
Tightening torque:
Wheel axle nut:
90 Nm (9.0 m·kg)
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 55
6-36
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU01495Front wheel installation
1. Install the speedometer gear
unit housing into the wheel
hub. Make sure the projections
are meshed into the slots.
2. Lift up the wheel between the
front fork legs. Make sure that
there is enough gap between
the brake pads before inserting
the brake disc and that the slot
in the speedometer gear unit
housing fits over the stopper
on the front fork outer tube.3. Install the wheel axle and axle
nut. Then, let the motorcycle
down.
4. Tighten the axle nut to the
specified torque.
5. Install the speedometer cable.EAU01496Rear wheel removalEW000122
w
8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so there is no danger of it
falling over.
1. Loosen the wheel axle nut.
2. Remove the brake adjusting
nut and brake rod from the
brake cam lever.
1. Wheel axle nut
2. Chain adjusting plate
3. Brake adjusting nut
4. Brake rod
21
a
b
34
Tightening torque:
Axle nut:
90 Nm (9.0 m·kg)
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 66
6-37
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9 3. Turn the chain adjusting plates
on each side fully in direction
b.
4. Elevate the rear wheel.
5. Remove the axle nut.
6. Pull out the rear axle.
7. Push the wheel forward and
remove the drive chain.
8. Remove the wheel assembly.
EAU01497Rear wheel installation
1. Install the wheel assembly and
insert the axle from the left-
hand side. Be sure that the
chain adjusting plates are
installed with the punched side
outward and the slot in the
brake shoe plate fits over the
stopper on the swingarm.
2. Install and adjust the drive
chain. (See page 6-24 for
details about adjusting the
drive chain slack.)
3. Install the axle nut and let the
motorcycle down.4. Tighten the axle nut to the
specified torque.
5. Insert the brake rod into the
brake cam lever and install the
brake pedal free play adjusting
nut.
6. Adjust the rear brake pedal
free play. (See page 6-20.)EW000103
w
Check the operation of the brake
light after adjusting the rear brake.
Tightening torque:
Axle nut:
90 Nm (9.0 m·kg)
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 67
