2000 YAMAHA DT125R brake light

EAU00009
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9 GIVE SAFETY THE RIGHT OF WAY..................1-1
DESCRIPTION....................................................2-1
Left view............................................................2-1
Right view.........................................................2-2
Controls/Instruments.........................................2-3
INSTRUMENT AND CONTROL FUNCTIONS....3-1
Main switch.......................................................3-1
Indicator lights...................................................3-1
Oil level indicator circuit check..........................3-2
Speedometer....................................................3-3
Tachometer.......................................................3-3
Engine temperature gauge...............................3-4
Handlebar switches..........................................3-4
Clutch lever.......................................................3-5
Shift pedal.........................................................3-5
Front brake lever...............................................3-6
Rear brake pedal..............................................3-6
Fuel tank cap....................................................3-6
Fuel (except for Switzerland and Austria).........3-7
Fuel (for Switzerland and Austria)....................3-7
Catalyzer (for Switzerland and Austria)............3-8
Two-stroke engine oil........................................3-9
Fuel cock..........................................................3-9
Starter (choke) Ò
1Ó.........................................3-10Kick starter......................................................3-11
Steering lock...................................................3-11
Seat................................................................3-12
Helmet holder.................................................3-12
Rear shock absorber adjustment....................3-13
Rear carrier.....................................................3-14
Note on handling of the Yamaha Energy
Induction System (Y.E.I.S.).............................3-14
Y.P.V.S.
(Yamaha Power Valve System)......................3-15
Sidestand........................................................3-15
Sidestand switch operation check..................3-16
PRE-OPERATION CHECKS...............................4-1
Pre-operation check list....................................4-1
OPERATION AND IMPORTANT RIDING
POINTS................................................................5-1
Starting the engine............................................5-1
Starting a warm engine.....................................5-3
Shifting..............................................................5-4
Recommended shift points
(for Switzerland only)........................................5-4
Tips for reducing fuel consumption...................5-5
Engine break-in.................................................5-5
Parking..............................................................5-6
123
45
3MB-9-E7 12/27/00 2:52 PM Page 5

PERIODIC MAINTENANCE AND MINOR
REPAIR................................................................6-1
Tool kit..............................................................6-1
Periodic maintenance and lubrication chart......6-3
Cowling removal and installation......................6-6
Cowling A..........................................................6-6
Cowling B..........................................................6-7
Cowling C.........................................................6-8
Panel removal and installation..........................6-8
Panel D.............................................................6-9
Panel E.............................................................6-9
Spark plug.......................................................6-10
Transmission oil..............................................6-11
Cooling system...............................................6-12
Changing the coolant......................................6-13
Air filter............................................................6-15
Carburetor adjustment....................................6-16
Idle speed adjustment.....................................6-17
Throttle cable free play adjustment.................6-17
Tires................................................................6-18
Wheels............................................................6-20
Clutch lever free play adjustment...................6-21
Front brake lever free play adjustment...........6-21
Rear brake pedal height adjustment...............6-22
Brake light switch adjustment.........................6-23
Checking the front and rear brake pads.........6-23Inspecting the brake fluid level.......................6-24
Brake fluid replacement..................................6-25
Drive chain slack check..................................6-25
Drive chain slack adjustment..........................6-26
Drive chain lubrication....................................6-26
Cable inspection and lubrication.....................6-27
Throttle cable and grip lubrication...................6-27
Autolube pump adjustment.............................6-28
Brake and shift pedal lubrication.....................6-28
Brake and clutch lever lubrication...................6-28
Sidestand lubrication......................................6-29
Front fork inspection.......................................6-29
Steering inspection.........................................6-30
Wheel bearings...............................................6-30
Battery............................................................6-31
Fuse replacement...........................................6-33
Headlight bulb replacement............................6-33
Turn signal light bulb replacement..................6-35
Tail/brake light bulb replacement....................6-35
Supporting the motorcycle..............................6-36
Front wheel removal.......................................6-36
Front wheel installation...................................6-37
Rear wheel removal........................................6-38
Rear wheel installation....................................6-39
Troubleshooting..............................................6-39
Troubleshooting chart.....................................6-40
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
6
3MB-9-E7 12/27/00 2:52 PM Page 6

4-2
PRE-OPERATION CHECKS
1
2
34
5
6
7
8
9
ITEMCHECKSPAGE
Brake and shift pedal shafts9Check for smooth operation.
6-28 9Lubricate if necessary.
Brake and clutch lever pivots9Check for smooth operation.
9Lubricate if necessary.
Sidestand pivot9Check for smooth operation.
6-29
9Lubricate if necessary.
Chassis fasteners9Make sure that all nuts, bolts and screws are properly tightened.
Ñ
9Tighten if necessary.
Fuel tank9Check fuel level.
3-6 ~ 3-8
9Fill with fuel if necessary.
Lights, signals and
9Check for proper operation.6-33 ~ 6-35
switches
Battery9Check fluid level.
6-31 ~ 6-32
9Fill with distilled water if necessary.
NOTE:
Pre-operation checks should be made each time the motorcycle is used. Such an inspection can be accomplished in a
very short time; and the added safety it assures is more than worth the time involved.wIf any item in the Pre-Operation Check is not working properly, have it inspected and repaired before operating
the motorcycle.
3MB-9-E7 12/27/00 2:52 PM Page 30

6-5
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EAU03884
NOTE:
8The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
8Hydraulic brake service
9Regularly check and, if necessary, correct the brake fluid level.
9Every two years replace the internal components of the brake master cylinders and calipers, and change the
brake fluid.
9Replace the brake hoses every four years and if cracked or damaged.21
*Carburetor¥Check starter (choke) operation.
¥Adjust engine idling speed.ÖÖÖÖÖÖ
22*Autolube pump¥Check operation.
¥Bleed if necessary.ÖÖÖÖ
23Transmission oil¥Check oil level.ÖÖÖÖÖÖ
¥Change.ÖÖ
24*Cooling system¥Check coolant level and vehicle for coolant leakage.ÖÖÖÖÖ
¥Change.Every 3 years
25*Front and rear brake
switches¥Check operation.ÖÖÖÖÖÖ
26Moving parts and cables¥Lubricate.ÖÖÖÖÖ
27*Lights, signals and
switches¥Check operation.
¥Adjust headlight beam.ÖÖÖÖÖÖ NO.ITEMCHECK OR MAINTENANCE JOBODOMETER READING (´ 1,000 km)
ANNUAL
CHECK
16121824
3MB-9-E7 12/27/00 2:52 PM Page 41

6-23
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EAU00713
Brake light switch
adjustmentThe rear brake light switch is activat-
ed by the brake pedal and is properly
adjusted when the brake light comes
on just before braking takes effect.
To adjust the rear brake light switch,
hold the switch body so it does not
rotate while turning the adjusting nut.
Turn the adjusting nut in direction a
to make the brake light come on earli-
er.
Turn the adjusting nut in direction b
to make the brake light come on
later.
b
a 1
2
1.Brake light switch
2.Adjusting nut
EAU00717
Checking the front and rear
brake padsCheck the brake pads for damage
and wear. If the thickness is less than
the specified value, have a Yamaha
dealer replace the pads.
1
1.Wear limit: 0.8 mm FRONT
1
1.Wear limit: 0.8 mmREAR
3MB-9-E7 12/27/00 2:52 PM Page 59

6-35
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
1
2
3
1
2
3
1.Screw (´2)
2.Lens
3.Bulb 1.Screw
2.Lens
3.Bulb
EAU01095
Turn signal light bulb
replacement1.Remove the screw and the lens.
2.Remove the defective bulb by
pushing it inward and turning it
counterclockwise.
3.Install a new bulb by pushing it
inward and turning it clockwise.
4.Install the lens and tighten the
screw.
EAU01623*
Tail/brake light bulb
replacement1.Remove the screws and the
lens.
2.Remove the defective bulb by
pushing it inward and turning it
counterclockwise.
3.Install a new bulb by pushing it
inward and turning it clockwise.
4.Install the lens and tighten the
screws.
EC000108
cCDo not over-tighten the screws as
the lens may break.
3MB-9-E7 12/27/00 2:52 PM Page 71

7-2
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
67
8
9 8 8
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.
8 8
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.8 8
Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel bearings, swingarm
bearings, forks and brakes),
electric components (cou-
plers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
8 8
For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure they
do not leave any marks. If the
windshield is scratched, use a
quality plastic polishing com-
pound after washing.
After riding in the rain, near the seaor on salt-sprayed roadsSince sea salt or salt sprayed on the
roads in the winter are extremely cor-
rosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads. (Salt sprayed
in the winter may remain on the roads
well into spring.)
1.Clean your motorcycle with cold
water and soap after the engine
has cooled down.
ECA00012
cCDo not use warm water since it
increases the corrosive action of
the salt.2.Be sure to apply a corrosion pro-
tection spray on all (even
chrome- and nickel-plated) metal
surfaces to prevent corrosion.
3MB-9-E7 12/27/00 2:52 PM Page 79

SPECIFICATIONS
1
2
3
4
5
6
78
9
8-4 Battery
TypeGM3-3B
Voltage, capacity12 V, 3 AH
Headlight typeConventional incandescent bulb
Bulb voltage, wattage ´quantity
Headlight12 V, 45/40 W ´1
Tail / Brake light12 V, 5/21 W ´1
Front flasher light12 V, 21 W ´2
Rear flasher light12 V, 21 W ´2
Auxiliary light12 V, 4 W ´1
12 V, 3.4 W ´1 (GB only)
Meter light12 V, 3.4 W ´2
Neutral indicator light12 V, 3.4 W ´1
High beam indicator light12 V, 3.4 W ´1
Oil level indicator light12 V, 3.4 W ´1
Turn indicator light12 V, 3.4 W ´1
Fuse
Main10 A
3MB-9-E7 12/27/00 2:52 PM Page 86