2000 SUZUKI SWIFT Sensor

MANUAL TRANSMISSION 7A-1
6F1
6F2
6G
6H
6K
7A1
7B1
7C1
7A
7E
7F
8A
8B
8C
8D
8E
9
10
10A
10B
SECTION 7A
MANUAL TRANSMISSION
CONTENTS

GENERAL DESCRIPTION .............................. 7A-2
CONSTRUCTION AND SERVICING ........... 7A-2
TRANSMISSION FOR 2WD MODEL....... 7A-3
TRANSMISSION FOR 4WD MODEL....... 7A-4
DIAGNOSIS ..................................................... 7A-5
ON-VEHICLE SERVICE .................................. 7A-5
OIL CHANGE ............................................... 7A-6
DIFFERENTIAL SIDE OIL SEAL ................. 7A-6
GEAR SHIFT CONTROL LEVER AND
CABLE ......................................................... 7A-8
VEHICLE SPEED SENSOR (VSS) ............ 7A-10
UNIT REPAIR OVERHAUL ........................... 7A-11
TRANSMISSION UNIT............................... 7A-11
TRASMISSION CASE ................................ 7A-12
INPUT & COUNTER SHAFT...................... 7A-13
GEAR SHIFTER & DIFFERENTIAL ........... 7A-14
TRANSMISSION UNIT............................... 7A-16
UNIT DISASSEMBLY ................................ 7A-17
FIFTH GEARS........................................ 7A-17GEAR SHIFTER, INPUT SHAFT AND
COUNTER SHAFT................................. 7A-19
RIGHT CASE ......................................... 7A-20
SUB ASSEMBLY SERVICE ...................... 7A-21
RIGHT CASE ......................................... 7A-21
LEFT CASE............................................ 7A-21
INPUT SHAFT ASSEMBLY ................... 7A-22
COUNTER SHAFT ASSEMBLY ............ 7A-25
GEAR SHIFTER..................................... 7A-29
DIFFERENTIAL ASSEMBLY ................. 7A-30
UNIT ASSEMBLY ...................................... 7A-33
DIFFERENTIAL TO LEFT CASE ........... 7A-33
FIFTH GEARS ....................................... 7A-35
GEAR SHIFT AND SELECT SHAFT
ASSEMBLY ............................................ 7A-38
TIGHTENING TORQUE SPECIFICATION.... 7A-39
REQUIRED SERVICE MATERIAL................ 7A-40
SPECIAL TOOL ............................................ 7A-40

WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System :
• Service on and around the air bag system components or wiring must be performed only by an
authorized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under
“General Description” in air bag system section in order to confirm whether you are performing ser-
vice on or near the air bag system components or wiring. Please observe all WARNINGS and “Ser-
vice Precautions” under “On-Vehicle Service” in air bag system section before performing service
on or around the air bag system components or wiring. Failure to follow WARNINGS could result in
unintentional activation of the system or could render the system inoperative. Either of these two
conditions may result in severe injury.
 Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system
may be activated by reserve energy in the Sensing and Diagnostic Module (SDM).

MANUAL TRANSMISSION 7A-3
TRANSMISSION FOR 2WD MODEL
1. 5th speed sleeve & hub 8. Reverse idler gear 15. Countershaft 3rd gear
2. Input shaft 5th gear 9. Input shaft 16. Countershaft 2nd gear
3. Input shaft 4th gear 10. Right case 17. Low speed sleeve & hub
4. High speed sleeve & hub 11. Side cover 18. Countershaft 1st gear
5. Input shaft 3rd gear 12. Countershaft 5th gear 19. Final gear
6. Left case 13. Countershaft 4th gear 20. Differential case
7. Reverse gear shaft 14. Countershaft 21. Vehicle speed sensor

7A-4 MANUAL TRANSMISSION
TRANSMISSION FOR 4WD MODEL
1. 5th speed sleeve & hub 7. Reverse gear shaft 13. Countershaft 4th gear 19. Final gear
2. Input shaft 5th gear 8. Reverse idler gear 14. Countershaft 20. Differential case
3. Input shaft 4th gear 9. Input shaft 15. Countershaft 3rd gear 21. Vehicle speed sensor
4. High speed sleeve & hub 10. Right case 16. Countershaft 2nd gear 22. Transfer assembly
5. Input shaft 3rd gear 11. Side cover 17. Low speed sleeve & hub
6. Left case 12. Countershaft 5th gear 18. Countershaft 1st gear

7A-10 MANUAL TRANSMISSION
VEHICLE SPEED SENSOR (VSS)
REMOVAL
1) Disconnect negative cable at battery.
2) Disconnect VSS coupler (1).
3) Remove VSS.
INSTALLATION
1) Check O-ring (1) and VSS surface for their flawlessness,
apply grease to O-ring and then install VSS to transmission.
Grease 99000-25010
2) Connect negative cable at battery.
3) Connect VSS coupler (1).

MANUAL TRANSMISSION 7A-15
[A] : GEAR SHIFTER 12. Reverse gear shift arm 25. Reverse gear shift lever bolt
: Apply thread lock 99000-32110 to all around
thread part of bolt.
[B] : DIFFERENTIAL 13. 5th gear shift fork 26. 5th gear shift fork plug
: Apply thread lock 99000-32110 to all around
thread part of plug.
1. Gear shift & select shaft 14. Side gear washer 27. Guide case
2. 5th & reverse gear shift cam 15. Differential side pinion gear 28. Select lever shaft bush
: Apply grease 99000-25010 to whole area of
bush.
3. Gear shift interlock plate 16. Differential side gear 29. Select lever boss
: Apply grease 99000-25010 to internal and exter-
nal diameter
4. Gear shift & select lever 17. Side gear washer 30. Final gear bolt
: Apply thread lock 99000-32110 to all around
thread part of bolt
5. Shift cable lever 18. Differential side oil seal
: Apply grease 99000- 25010 to oil
seal lip.31. Differential pinion shaft
6. Select cable lever 19. Differential side bearing 32. Differential pinion shaft pin
7. Low speed gear shift shaft 20. Speed sensor ring Tightening torque
8. High speed gear shift shaft 21. Differential case Do not reuse.
9. 5th & reverse gear shift shaft 22. Final gear Apply transmission oil.
10. Reverse gear shift lever 23. 5th to reverse interlock guide bolt
: Apply sealant 99000-31110 to bolt
thread.
11. 5th & reverse gear shift guide
shaft24. Gear shift interlock bolt
: Apply sealant 99000-31110 to bolt
thread.

7A-30 MANUAL TRANSMISSION
2) Insert each gear shift shaft into case and check that it moves
smoothly. If it doesn’t, correct by using oilstone, reamer or
the like.
5th & Reverse Gear Shifter
1) Disassemble component parts by using special tool and
hammer.
Special tool
(A) : 09922-85811
2) Replace or correct parts as required and assemble shafts
making sure that component parts are in proper order as
shown in figure.
DIFFERENTIAL ASSEMBLY
DISASSEMBLY
1) Using special tools, remove right bearing (1) and sensor
rotor (2).
Special tool
(A) : 09913-60910
(B) : 09925-88210
2) Remove left bearing in the same manner.
3) Support differential case with soft jawed vise and remove
final gear bolts then take out final gear. NOTE:
 Distinguish reverse gear shift arm spring (Blue) (2)
from low speed locating spring (Yellow).
 Install 2 steel balls (3) in reverse gear shift arm (1) with-
out fail.
 Drive in spring pin for reverse shift arm facing slit A
toward front.
1. Reverse gear shift arm 6. 5th & reverse gear shift yoke
2. Reverse gear shift arm spring (Blue) 7. 5th & reverse gear shift guide shaft
3. Steel ball 8. 5th gear side
4. Spring pin A: Face pin slit toward 5thn gear side
5. 5th & reverse gear shift shaft

7A-32 MANUAL TRANSMISSION
3) Drive in new differential pinion shaft pin (2) till the depth from
differential case (3) surface is about 1 mm (0.04 in.).
4) Press-fit new sensor rotor (1) with groove (4) side downward
as shown by using special tools and copper hammer.
Special tool
(A) : 09913-75510
(B) : 09940-54910
5) Press-fit left bearing by using special tools and copper ham-
mer.
6) Support differential assembly (1) as illustrated so as to left
bearing (2) is floating, and then press-fit right bearing (3) like
left bearing in Step 5).
Special tool
(C) : 09951-76010
(D) : 09951-16060
7) Hold differential assembly with soft jawed vise (3), install final
gear (2) as shown in figure and then tighten bolts (1) with
thread lock cement applied to specified torque.
“A” : Thread lock cement 99000-32110
Tightening torque
Final gear bolts (a) : 90 N·m (9.0 kg-m, 65.0 lb-ft)
NOTE:
Make sure to install final gear in correct installing direc-
tion.
CAUTION:
Use of any other bolts than specified ones is prohibited.
4. Groove

MANUAL TRANSMISSION 7A-41
09923-74510 09923-78210 09924-74510 09925-18011
Bearing remover Bearing installer Installer attachment Bearing installer
09925-68210 09925-78210 09925-88210 09925-98221
Bearing outer race
installerSpring pin remover 6 mm Bearing puller attachment Bearing installer
09927-76010 09930-30104 09940-53111 09940-54910
Gear holder Sliding shaft Bearing installer Sensor rotor installer
09941-64511 09951-16060 09951-76010
Bearing remover Bush remover Bearing installer