2000 SUZUKI SWIFT automatic transmission

AUTOMATIC TRANSMISSION (4 A/T) 7B-25
[INTERMITTENT TROUBLES] and [NOTES ON SYSTEM CIR-
CUIT INSPECTION]
Refer to Section 0A.
DTC CHECK
[Check DTC with SUZUKI scan tool]
1) Turn ignition switch OFF.
2) After setting cartridge, connect SUZUKI scan tool to data link
connector (DLC) (1) located on underside of instrument
panel at driver’s seat side.
Special tool
(A) : 09931-76011 (SUZUKI scan tool)
(B) : Mass storage cartridge
(C) : 09931-76030 (16/14 pin DLC cable)
3) Turn ignition switch ON.
4) Read DTC according to instructions displayed on SUZUKI
scan tool and print it or write it down. Refer to SUZUKI scan
tool operator’s manual for further details.
5) After completing the check, turn ignition switch OFF and dis-
connect SUZUKI scan tool from data link connector (DLC)
(1).
[Check DTC without SUZUKI scan tool]
1) Turn ignition switch ON and make sure that O/D OFF lamp is
OFF in combination meter (O/D off switch OFF).
2) Turn ignition switch OFF.
3) Pull out clip (3) and remove glove box (2) from instrument
panel (1).

7B-26 AUTOMATIC TRANSMISSION (4 A/T)
4) Using service wire, ground diagnosis switch terminal (2) of
monitor connector No.2 (1).
5) Turn ignition switch ON.
6) Read DTC from flashing pattern of O/D OFF lamp.
7) After completing the DTC check, turn ignition switch OFF
and disconnect service wire from monitor connector No.2
(1).
3. Ground terminal
1
2
3

AUTOMATIC TRANSMISSION (4 A/T) 7B-27
DTC CLEARANCE
[Clear DTC with SUZUKI scan tool]
1) Turn ignition switch OFF.
2) After setting cartridge to scan tool, connect it to data link
connector (DLC) (1) located on underside of instrument
panel at driver’s seat side.
Special tool
(A) : 09931-76011 (SUZUKI scan tool)
(B) : Mass storage cartridge
(C) : 09931-76030 (16/14 pin DLC cable)
3) Turn ignition switch ON.
4) Erase DTC according to instructions displayed on scan tool.
Refer to SUZUKI scan tool operator’s manual for further
details.
5) After completing the clearance, turn ignition switch OFF and
disconnect scan tool from data link connector (DLC) (1).
[Clear DTC without SUZUKI scan tool]
1) Turn ignition switch ON.
2) Using service wire, ground diagnosis switch terminal (2) of
monitor connector No.2 (1) five times within 10 seconds.
3) Perform “DTC check” and confirm that only DTC12 (normal
DTC) is displayed. If not, repeat step 1) and 2) and check
again.
3. Ground terminal
1
2
3

7B-28 AUTOMATIC TRANSMISSION (4 A/T)
DTC TABLE
DTC NO.
“O/D OFF” Lamp
Flashing Pattern of DTC
(Not using scan tool)DETECTING ITEMSMIL
Using
scan toolNot using
scan toolVehicle
equipped
with
immobi-
lizer indi-
cator lampVehicle
equipped
without
immobi-
lizer indi-
cator lamp
–12 Normal––
P0715 14Input/Turbine speed sensor circuit
malfunction1 driving
cycleNot
applicable
P0730 18 Incorrect gear ratio2 driving
cyclesNot
applicable
P075321
Shift solenoid-A (No.1) electrical1 driving
cycleNot
applicable
22
P075823
Shift solenoid-B (No.2) electrical1 driving
cycleNot
applicable
24
P0763 43 Shift solenoid-C (No.3) electrical1 driving
cycleNot
applicable
P0768 45 Shift solenoid-D (No.4) electrical1 driving
cycleNot
applicable
P0773 48 Shift solenoid-E (No.5) electrical1 driving
cycleNot
applicable
P074325
Torque converter clutch (lock-up)
system electrical1 driving
cycleNot
applicable
26

AUTOMATIC TRANSMISSION (4 A/T) 7B-29
P0741 29Torque converter clutch (lock-up)
solenoid performance or stuck off2 driving
cyclesNot
applicable
P0720 31Output shaft speed sensor circuit
malfunction1 driving
cycleNot
applicable
P170032
Throttle position signal input mal-
function1 driving
cycleNot
applicable
33
P0705 34Transmission range sensor circuit
malfunction1 driving
cycleNot
applicable
P0725 35Engine speed input circuit malfunc-
tion2 driving
cyclesNot
applicable
P071036
Transmission temperature sensor
circuit malfunction2 driving
cyclesNot
applicable
38
P1709 51Engine coolant temperature signal
circuit1 driving
cycleNot
applicable
P0702
52Transmission control system elec-
trical1 driving
cycleNot
applicable
P1702 Internal malfunction of TCMDTC NO.
“O/D OFF” Lamp
Flashing Pattern of DTC
(Not using scan tool)DETECTING ITEMSMIL
Using
scan toolNot using
scan toolVehicle
equipped
with
immobi-
lizer indi-
cator lampVehicle
equipped
without
immobi-
lizer indi-
cator lamp

7B-30 AUTOMATIC TRANSMISSION (4 A/T)
TCM POWER AND GROUND CIRCUIT CHECK
1. Battery 4. Circuit fuse (IG) 7. TCM
2. Main fuse 5. Ground
3. Ignition switch 6. A/T relay
DTC DETECTING CONDITION
Automatic transmission doesn’t shift to 1st gear at vehicle start in “D” range.
Step Action Yes No
1 Check voltage between terminal “C44-2” of
TCM coupler and body ground with ignition
switch ON.
Is it 10 – 14 V?Go to Step 2. YEL/BLK wire open or
faulty
A/T relay.
2 Check voltage between terminal “C44-15” of
TCM coupler and body ground with ignition
switch ON.
Is it about 0 V?Poor “C44-2” or “C44-15”
connection.
If all above are OK,
replace known-good TCM
and recheck.“BLK” wire open.

AUTOMATIC TRANSMISSION (4 A/T) 7B-31
DTC P0715 (DTC NO.14) INPUT/TURBINE SPEED SENSOR CIRCUIT MALFUNCTION
1. Input shaft speed sensor 2. TCM coupler (viewed from harness side) 3. TCM
DTC DETECTING CONDITION
Input shaft speed sensor signal voltage too high or too low.
Step Action Yes No
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC
FLOW TABLE” performed?Go to Step 2. Go to “AUTOMATIC
TRANSMISSION DIAG-
NOSTIC FLOW TABLE”.
2 1) Turn ignition switch OFF and disconnect output shaft
speed sensor – input shaft speed sensor coupler.
2) Measure resistance between terminals of the discon-
nected sensor side coupler.
Is it 160–200 Ω
?
(See figure.)Go to Step 3. Replace input shaft speed
sensor.
3 1) Connect output shaft speed sensor - input shaft
speed sensor coupler then disconnect TCM couplers.
2) Measure resistance between terminal “C43-7” and
“C43-15” of disconnected harness side coupler.
Is it 160–200 Ω
?Go to Step 4.“BLU/YEL” or “RED/WHT”
wire open or shorted each
other.
4 1) Turn ignition switch OFF and connect input shaft
speed sensor coupler then disconnect TCM couplers.
2) Measure resistance between terminal “C43-7” (of dis-
connected harness side coupler) and body ground
then terminal “C43-15” (of disconnected harness side
coupler) and body ground.
Are they about 0 Ω
?
(See figure.)Short in
between “BLU/
YEL” wire and
ground or “RED/
WHT” wire and
ground.Poor connection of termi-
nal “C43-7” or “C43-15” of
TCM.
If all the above are in
good condition, substitute
a known-good TCM and
recheck.

7B-32 AUTOMATIC TRANSMISSION (4 A/T)
Figure for Step 2
Figure for Step 4
1. Output shaft speed sensor - Input shaft speed sensor coupler
2. Input shaft speed sensor terminal