2000 SUZUKI SWIFT service

9-56 BODY SERVICE
“A” : Apply sealant
“B” : Smooth out sealant with a brush
“C” : Wipe off excess sealant after application

BODY SERVICE 9-57
“A” : Apply sealant
“B” : Apply sealant so that top of flange covered up certainly

9-58 BODY SERVICE
UNDER COATING APPLICATION AREAS
“A” :Apply undercoating (PCV, 400 µm or more)“C” : Apply anti-chip coat (300 µm or more)
“B” : Apply anti-chip coat (100 µm or more)“D” : Do not apply undercoating

BODY SERVICE 9-59
“A” : Apply undercoating (PCV, 400 µm or more)
“B” : Apply undercoating (PCV, 600 µm or more)
“C” : Do not apply undercoating

9-60 BODY SERVICE
ANTI-CORROSION COMPOUND APPLICATION AREA
“A” : Apply rust proof wax (hot wax 50 µm or more)
“B” : Apply rust proof wax (low viscosity wax 10 µm or more)
“C” : Apply rust proof wax (high viscosity wax 50 µm or more)

BODY SERVICE 9-61
PLASTIC PARTS FINISHING
Paintable plastic parts are ABS plastic parts.
Painting
Rigid or hand ABS plastic needs no primer coating.
General acrylic lacquers can be painted properly over hard ABS plastic in terms of adherence.
1) Use cleaning solvent for paint finish to wash each part.
2) Apply conventional acrylic color lacquer to part surface.
3) Follow lacquer directions for required drying time. (Proper drying temperature range is 60 – 70 °C (140 – 158
°F)).
Reference
Plastic parts employ not only ABS (Acrylonitrile Butadiene Styrene) plastic but also polypropylene, vinyl, or the
like plastic. Burning test method to identify ABS plastic is described below.
1) Use a sharp blade to cut off a plastic sliver from the part at its hidden backside.
2) Hold sliver with pincers and set it on fire.
3) Carefully observe condition of the burning plastic.
4) ABS plastic must raise readily distinguishable back smoke while burning with its residue suspended in air
temporarily.
5) Polypropylene must raise no readily distinguishable smoke while burning.
REQUIRED SERVICE MATERIAL
Material Recommended SUZUKI product Use
Lithium grease SUZUKI SUPER GREASE A
(99000-25010)Window regulator
Door hinge
Sealant SUZUKI BOND No. 1215
(99000-31110)Hood hinge
Door hinge

9-62 BODY SERVICE

RESTRAINT SYSTEM 10-1
6F1
6F2
6G
6H
6K
7A
7A1
7B1
7C1
7D
7E
7F
8A
8B
8C
8D
8E
9
10
10A
10B
SECTION 10
RESTRAINT SYSTEM
CONTENTS
GENERAL DESCRIPTION .............................. 10-2
SYSTEM SPECIFICATION .......................... 10-3
SEAT BELT PRETENSIONER
(IF EQUIPPED) ............................................ 10-3
DIAGNOSIS ..................................................... 10-3
INSPECTION AND REPAIR REQUIRED
AFTER ACCIDENT ...................................... 10-3
ON-VEHICLE SERVICE .................................. 10-4SERVICE PRECAUTIONS .......................... 10-4
SERVICE AND DIAGNOSIS .................... 10-4
DISABLING AIR BAG SYSTEM............... 10-4
ENABLING AIR BAG SYSTEM................ 10-4
HANDLING AND STORAGE ................... 10-4
DISPOSAL ............................................... 10-4
FRONT SEAT BELT .................................... 10-5
REAR SEAT BELT....................................... 10-8

WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System with seat belt pretensioner:
Service on or around the air bag system components or wiring must be performed only by an
authorized SUZUKI dealer. Please observe all WARNINGS and “Service Precautions” under “On-
Vehicle Service” in air bag system section before performing service on or around the air bag sys-
tem components or wiring. Failure to follow WARNINGS could result in unintentional activation of
the system or could render the system inoperative. Either of these two conditions may result in
severe injury.
The procedures in this section must be followed in the order listed to disable the air bag system
temporarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures
could result in possible activation of the air bag system, personal injury or otherwise unneeded air
bag system repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were
removed. If a fastener needs to be replaced, use the correct part number fastener for that application.
If the correct part number fastener is not available, a fastener of equal size and strength (or stronger)
may be used. Fasteners that are not reused, and those requiring thread-locking compound, will be
called out. The correct torque value must be used when installing fasteners that require it. If the above
procedures are not followed, parts or system damage could result.